Table of Contents
Advertisement
Weekly Timer Program built into the Iris Plus Control Panel
Weekly time programmer built into panel
Using the weekly time programmer built into the central panel
it is possible to set 3 ignition programmes:
• Pr02 with settable on and off times;
• Pr02 with settable on and off times;
• Pr03 with settable on and off times.
It is possible to enable one or more of the three settings on
each day of the week (day1 = Monday, day2 = Tuesday...
day7 = Sunday).
When on standby, the display alternates between showing the
ignition mode (P1, P2, P3 or a temperature) and the clock.
Refer to page 10 for each of the buttons to press.
Setting the clock
1. Hold the MENU key down for about two seconds until IP
appears then release, tS appears.
2. Press the MENU key three times until Prog appears.
3. Press the "-" key until SEt appears.
4. Press the MENU key until the clock appears. It may be
changed with the "-" key, which decreases the time by
one minute each time it is pressed, and with the "+" key,
which increases it by 15 minutes each time it is pressed.
5. Once the time is set, confirm with the MENU key.
6. The day number appears (dAY1=Monday,
dAY2=Tuesday... dAY7=Sunday), which can be changed
with the "-" and "+" keys.
7. Confirm with the MENU key. Prog appears.
8. Press the 0/1 key to quit clock setting.
Enabling programmes
1. Hold the MENU key down for about two seconds until IP
appears then release, tS appears.
2. Press the MENU key three times until Prog appears.
3. Press the "+" key until ProF appears.
Note: PrON will be displayed if programming has previously been enabled.
If so you can exit thie section by pressing O/1 and proceed to setting
program section.
4. Press the MENU key until OFF appears.
5. Press the "+ " or "–" key until PrOn appears.
6. Confirm with the MENU key. Prog appears.
7. Press the O/1 key to return to standby.
8. The pellet fire is now in PrOn mode and will accept timed
on and off commands.
Setting a program (e.g. Pr01)
1. Hold the MENU key down for about two seconds until IP
appears then release, tS appears.
2. Press the MENU key three times until Prog appears.
3. Press the "+" key twice until Pr 1 appears.
4. Press the MENU key until OnP1 appears together with the
"on time". It may be changed with the "+" and "–" keys in
ten-minute intervals.
5. Press the MENU key to confirm. OfP1 appears together
with the off time. This may be changed with the "+" and
"-" keys in ten-minute intervals.
6. Press MENU to confirm. "oFd1" appears (which means
program 1 is not enabled on day 1, Monday). This may be
changed into Ond1 (which means program 1 is enabled
on day 1, Monday) using the "+" and "-" keys.
7. Press MENU to move to the second day, and so on until
the desired day or days are selected then toggle on or off
as required. So for example you could program the pellet
fire to turn on at 4pm and off at 6pm Monday to Friday
with Program 1 then turning on at 8am and off at 10am
Saturday and Sunday with program 2.
8. Press the MENU key again and Prog appears.
9. To quit programming press the 0/1 key.
On and off times may be set for Pr 2 and Pr 3 in a similar way,
and it can be decided which days they are enabled on.
Note: You can override the pre-programmed settings if need be.
Note: Automatic cleaning .. every 20 minutes the combustion fan will
speed up for 10 seconds to blow excess ash from the burn pot.
PAGE 11
Hide quick links:
Advertisement
Table of Contents
