Step 9, Position Water Line And Housing Wiring; Step 10 Install Drain Hose To Dishwasher Drain Port - Monogram ZBD6920D00SS Installation Instructions Manual

Installation Instructions
STEP 7 INSTALL POWER CORD
Skipthis step if dishwasherwill be permanently connectedto
the houseelectricalsystem.
Inthis stepyouwill needthejunction boxcoverand the #10 x 1/2"
hexheadscrewfrom the screwkitset asidein Step1.
Thepowercordand connections mustcomplywith the National
Electrical C ode, S ection 422and/or localcodesand ordinances.
Maximumpowercordlengthis 6 feet.PowerCordKitWX09×709Z0,
available for purchase from an authorized GEAppliance Dealer,
meetstheserequirements.
j Black
Figure N --_
• Installstrain reliefinjunction box bracket.
• Insertpowercordthroughstrain reliefand tighten.
• Makesureblack,white and greendishwasher w iresare threaded
throughsmallholeinjunction boxbracket.
• Connectlike-colored dishwasher a nd powercordwires.If power
cordwiresare notcolorcoded,connectthe ribbedpowercord
wireto the white dishwasher w ire,the smoothpowercordwire
to the blackdishwasher w ire and the groundto the green
dishwasher w ire. UseUL-listed wire nutsof appropriatesize.
• Install j unction boxcoverset asidein StepZ,using#10 hexhead
screw.Besurewiresare not pinchedunderthe cover.
STEP 8 INSTALL 90 ° ELBOW
• Wrap90° elbowwith threadsealtape.
• Installa 90° elbowontothe water valve.
Front of Dishwasher
90 ° EIbow_
Bracket
_Fill Hose
Figure O
Thread Seal Tape
• Do notovertighten90° elbow,water valvebracketcouldbend
or water valvefitting couldbreak.
• Position the end of the elbowto face the rear of the dishwasher.
STEP 9 I POSITION WATER LINE AND
HOUSING WIRING
• Position water
supply
line and house wiring on the floor
of the enclosure to avoid interference with base of
dishwasher and components under dishwasher.
Line
Figure P Wiring
STEP 10 INSTALL DRAIN HOSE TO
DISHWASHER DRAIN PORT
In this step you will need the drain hose and clamp set
aside in Step 1.
• Stand the dishwasher upright.
• Place drain hose clamp over 1-3/16" inside diameter
end of drain hose with the clamp screw positioned
on the bottom of the hose.
IMPORTANT-
Prevent drain hosedamage and
possible leaks. Becareful not to nick or cut the drain hose.
• Push the end of the drain hose over the drain pump
outlet being careful not to disturb the check valve.
Refer to Figure O.
• Seat the drain hose end against the hose stops on
the pump outlet.
• Position hose clamp against the front lip of the drain
hose and tighten clamp.
NOTE:Drain hose
supplied with
dishwasher is
approximately 78"
long. If a longer hose
is needed, a 120"
long hose (10 feet),
may be purchased
from an authorized
GE appliance dealer.
The 10' long hose is
part number GPFIOL
Pum Hose Stops
Outlet
Tip for leak-free
connections:
• Insert hose against
stop on pump.
Hose Clam
• Position clamp
against front lip of drain hose.
• Tighten clamp to at least 15 inch-pounds of torque.
Tip for quiet drain pump operation:
Position hose clamp with clamp screw on the bottom side
of the hose.This will prevent the clamp from coming in
contact with the rear brace. Clamp contact with the rear
brace could create noise when the drain pump is running.