Table of Contents
Advertisement
Remote menu operation
An optional remote plug is available to enable operating
the camera mode and set buttons by remote control.
Confirm the plug is properly wired as indicated in the
figure and connect it to the rear panel Remote connector.
Do not connect anything to the unused Pins.
9
1
8
2
10
7
12
11
3
4
6
5
Remote plug(option)
External key switch connections for remote operation
Keep the distance between the remote plug and
external key switches to less than about 2 meters.
Disconnect the remote plug from the camera Remote
connector when not using the key switches.
Specifications
NTSC
1.Color system
1/2-inch progressive scan frame
2.Pickup element
interline CCD( with on-chip microlenses )
Total pixels
680(H)
Effective pixels
658(H)
Scanning area
6.58(H)
Sell size
10.0(H)
2:1 interlace
3.Scanning system
Hor. 15.734kHz
4.Scanning frequency
Ver. 59.94Hz
internal
5.Sync system
KP-DE500：VBS1.0Vp-p/75Ω
6. Video signal output
KP-E500：VS1.0Vp-p/75Ω
Digital processing ( input 10 bits )
7. Signal processing
8. S/N( Y signal )
More than 50dB
(AGC,enhancer and gamma OFF)
9. Resolution( Y signal at center )
10.Minimum illumination
KP-DE500
0.009 lx ( Color, F1.4, AGC ON, SENS UP OFF, 50IRE )
0.0005 lx( Monochrome, F1.4, AGC ON, SENS UP OFF, 50IRE )
0.00015lx(Color 64 time accumulation, F1.4, AGC ON, 50IRE)
0.000008lx
(Monochrome 64 time accumulation, F1.4, AGC ON, 50IRE)
33
UP
SET
DOWN
500(V)
×
489(V)
×
4.89(V)mm
×
10.0(V)μm
×
Hor. ：480 lines
Ver. ：350 lines
NOTE
Be sure to switch off the camera power before
connecting or disconnecting the remote plug.
Pin
Signal
Not connected
1
Serial data input
2
Serial data output
3
Up key
4
Down key
5
Not connected
6
Not connected
7
Set key
8
Not connected
9
GND
10
Not connected
11
Not connected
12
Remote operation with RS-232C
Signals 2, 3 and 10 can be used for control by personal
computer. Consult dealer for retailed information.
KP-E500
0.0003 lx
(Monochrome, F1.4, AGC ON, SENS UP OFF, 50IRE )
0.000005 lx
(Monochrome 64 time accumulation, F1.4, AGC ON, 50IRE)
11. Sensitivity setting
12. Electronic shutter speeds
Selectable in 7 steps & AES
( Factory setting is 1/60 )
1/60,1/100,1/125,1/250,1/500,1/1000,1/2000
AES:From 1/60 second to 1/2000 second
13. Integration multiple [SENS UP] setting
：Automatic or Manual (fixed) ( Factory setting is OFF )
Automatic : 2,4,6,8,10,12,16,32,64 times
Manual : 2,4,6,8,10,12,16,32,64,88,128 times
14. Backlight compensation
15.Auto-iris lens outputs
Video signal
Input type lens
Iris control voltage input
(galvanometer)
Abbrev.
Remarks
N.C.
Do not connect
Tx
Connect to RS-232C
data terminal
Rx
Connect to RS-232C
data terminal
UP
Key switch connection
DOWN
Key switch connection
N.C.
Do not connect
N.C.
Do not connect
SET
Key switch connection
N.C.
Do not connect
GND
Connect to RS-232C
ground
N.C.
Do not connect
N.C.
Do not connect
AGC OFF/ON(Factory setting is1/60)
Manual Gain Adjustable at AGC OFF
Limit Gain Adjustable at AGC ON
ON/OFFswitchable
Sensing area:selectable from 9 areas
Luminance signal
1.0Vp-p/high impedance
Power supply 12V DC 40mA
Coupling coil impedance
Damper:1150Ω±10%
Drive:190Ω±10%
32
Advertisement
Table of Contents
