Table of Contents
Advertisement
This barbecue is intended for use with LP cylinders equipped with a QCC-1 / OPD valve (Quick
IMPORTANT:
Connect Coupling Type 1 with Overfill Prevention Device) .
Purging and filling of LP-Gas cylinders must be performed by personnel who have been thor-
WARNING
oughly trained in accepted LP-Gas industry procedures. Failure to follow this instruction may
result in explosion, fire, severe personal injury, or death.
ALL NEW CYLINDERS MUST BE PURGED
BEFORE THE FIRST FILLING.
A)
Turn heat control knobs and Gas Cylinder valve to
"OFF" position.
B)
Propane cylinder equipped with QCC-1 valve (Figure 1)
is equipped with a right-handed thread. Turn black
plastic nut counter-clockwise to loosen.
QCC-1 CYLINDER VALVE
BLACK COUPLING NUT
Turn Clockwise to connect
REGULATOR
New Style QCC-1 OPD Connection
C)
Remove cylinder from Grill. Have cylinder filled by your
local Propane gas dealer.
D)
Some Propane Cylinders have a bleed-off valve (Fig. 1).
This bleed-off valve should be inspected for leaks after
each refilling of the tank. Turn clockwise to reseal.
E)
Fasten full Propane tank to Grill and connect QCC-1 fit-
ting to tank valve (Figure 1) by turning clockwise.
F)
With heat control knobs still at "OFF" position, turn on
Cylinder valve.
USING SOAP SOLUTION, TEST THE GAS CONNECTION
FOR LEAKS. (See Page 1 for information on mixing and
applying soap solution.) If bubbles appear, there is a leak;
tighten or correct gas connections as necessary. After check-
ing for leaks, turn valve off.
Gas Barbecue Assembly Instructions
1. Remove unit from carton carefully, ensuring drip tray
does not fall out.
2. Check barbecue for damage.
3. Check that proper orifices are installed in the valves.
IMPORTANT: The Turbo STS Barbecue is supplied from the
factory setup for Natural Gas and fitted with Natural Gas
Orifices (see Figure 2).
FILLING OR REFILLING THE PROPANE GAS CYLINDER
PRESSURE
RELIEF VALVE
BLEED-OFF
VALVE
Turn Clockwise
to Reseal
Figure 1
Figure 2
Main Burners
If you are going to use this barbecue with Propane, it
MUST be converted to operate on Propane gas by a
Barbeques Galore Technician or a qualified gas plumber.
A company supplied Propane Conversion Kit must be used
to convert the barbecue to the correct gas.
Conversion Procedure:
3a. Remove all the existing Natural
Gas Orifices.
3b. Locate
the
Orifices and install them into
the barbecue as shown in
Figure 3a.
3c. Place the new Propane Rating Label over the existing
label on the right hand side of the barbecue frame.
3d. Connect the barbecue to an appropriate regulated
Propane Gas supply.
The Natural Gas orifice has a substantially larger hole
size than the Propane orifice and is easily distinguishable. If
you have to change them, use a wrench to undo the orifice
from the valve (see Figure 3a) and install the correct orifice
making sure they are wrench tight. Do not over-tighten.
Repeat for the other orifices.
NOTE: Ensure barbecue is connected to the appropriate
regulated gas supply determined by the orifices. Failure
to use the appropriate gas regulator voids all warranties.
Conversion Procedure
for Rotis Burner:
(Rotis models only)
Remove Access Panel and
replace existing Natural Gas
Orifices #52 with the Propane
Gas Orifices #62.
This Gas Grill must be connected to an
appropriate REGULATED gas supply - refer to
Safety Information.
- 4 -
#50
#57
PROPANE:
NATURAL:
Propane
Gas
Valve
Figure 3b
Orifice
Orifice
Figure 3a
Rotis Burner
Hide quick links:
Advertisement
Table of Contents
