Assembly And Setup; Pro Upright Bike Assembly And Setup - Star Trac Pro Upright Bike Owner's Manual

A
SSEMBLY AND

PRO UPRIGHT BIKE ASSEMBLY AND SETUP

Use the following procedures to unpack and assemble your STAR TRAC PRO UPRIGHT BIKE.
U
NPACKING
Open the shipping carton, remove all parts from the carton and foam inserts, and verify that the following parts are included in
your shipment:
Description
Bike Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Display Console Assembly . . . . . . . . . . . . . . . . . . . . . . . 1
Seat Post Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Front Foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Rear Foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pedals (set of two) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Screw, Button Head, M10 X 30 . . . . . . . . . . . . . . . . . . . 8
Take time now to enter your Pro Bike serial number in the space below. If parts are missing, or if you have any operational ques-
tions, please call Star Trac's Service Department at (800) 503-1221; have your serial number ready.
Serial No. ___________________________
A
SSEMBLY
1. Install the Front Foot
The front foot assembly has wheels attached to the front
NOTE :
edge. Be sure the wheels face forward when installing the front
foot assembly.
Stand the bike frame upright and place the front foot assembly
under the frame, aligning the holes in the foot with the holes in the
frame.
Using the 6mm hex wrench and four M10 X 30 button head screws,
secure the front foot assembly to the frame. Tighten all four screws
securely.
2. Install the Rear Foot
NOTE: Be sure the rear foot assembly is positioned with the curved
edge facing forward (similar to the front foot).
Lift up the rear of the bike frame and place the rear foot assembly
in position under the frame, aligning the holes in the foot with the
holes in the frame.
Using the 6mm hex wrench and four M10 X 30 button head screws,
secure the rear foot assembly to the frame. Tighten all four screws
securely.
STAR TRAC PRO BIKES O
S
ETUP
Qty.
' G
WNER S UIDE
Description
Screw, Flat Head, M6 X 16 . . . . . . . . . . . . . . . . . . . . . . . 4
Screw, Socket Head, M6 X 10 . . . . . . . . . . . . . . . . . . . . . 1
Screw, Socket Head, M4 X 20 . . . . . . . . . . . . . . . . . . . . . 2
Wrench, Hex, 6mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Wrench, Hex, 4mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Multi-end Wrench, 10mm, 12mm, 15mm . . . . . . . . . . . . 1
Wrench, Hex, 3mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Qty.
Step 1
Step 2
11