Table of Contents
Advertisement
Quick Links
2-IN-1 NAILER/STAPLER KIT
MODEL H2912/H2913
INSTRUCTION MANUAL
Model H2913
Model H2912
COPYRIGHT © JANUARY, 2002 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN
Advertisement
Table of Contents
Related Manuals for Grizzly H2912
Summary of Contents for Grizzly H2912
-
Page 1: Instruction Manual
Model H2912 COPYRIGHT © JANUARY, 2002 BY GRIZZLY INDUSTRIAL, INC. 1821 VALENCIA ST., BELLINGHAM, WA 98227 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN TAIWAN... -
Page 2: Safety Instructions For Power Tools
For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progres- sion of symbols is described below. - Page 3 14. DO NOT OVERREACH. Keep proper footing and balance at all times. H2912/H2913 2-IN-1 NAILER/STAPLER 15. MAINTAIN TOOLS WITH CARE. 16. DISCONNECT TOOLS before ser- 17. REDUCE THE RISK OF UNINTEN- 18.
- Page 4 Always pay attention nailer/stapler is pointed. Use this tool with respect and caution to lessen the possibility of operator or bystander injury. Ignoring this warning may result in serious personal injury. H2912/H2913 2-IN-1 NAILER/STAPLER nailer/stapler dis- direction...
- Page 5 Commentary We are proud to offer the Grizzly Model H2912/H2913 2-IN-1 Nailer/Stapler. This model is part of a growing Grizzly family of fine power tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoy- able operation and proof of Grizzly’s com-...
-
Page 6: Compressed Air System
Compressed Air System The Model H2912/H2913 is designed to be operated at 60-100 psi. Do not exceed the maximum operating pressure for your model. Before you use your new nailer/stapler, install the ⁄ " quick connect fitting that comes with the nailer/stapler. Install a female ⁄... -
Page 7: Operation
Figure 2. Make sure that the pointed ends of the nails/sta- plers point in the same direction as the Model H2912/H2913 nose and the nails/staples rest in the slot at the bot- tom of the magazine. - Page 8 Always disconnect air from the nail- er/stapler whenever clearing a jam! To clear a jam from the magazine: To clear a jam from the discharge area: H2912/H2913 2-IN-1 NAILER/STAPLER Disconnect the nailer/stapler from the air supply! Open the magazine cover and pull the magazine all the way back.
- Page 9 As mentioned before, the best option is to install a filter/lubricator/regulator unit such as the Grizzly Model H2333 in your air line. Figure 5. Lubricating the nailer/stapler via air inlet. H2912/H2913 2-IN-1 NAILER/STAPLER...
-
Page 10: Replacing Pistons/O-Rings
Replacing Pistons/O-Rings If you use your nailer/stapler day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a pis- ton or piston shaft becomes worn out. To... - Page 11 H2912 PART BREAKDOWN H2912/H2913 2-IN-1 NAILER/STAPLER...
- Page 12 PH2912052 SHAFT PH2912053 LINER PH2912054 SET SCREW PH2912055 MAGAZINE STAPLE GUIDE UNIT PH2912056A END CORE ASBLY. PH2912057A PH2912058 CAP SCREW PH2912059 ROLLED PIN PH2912060 PUSHER PH2912061 SLIDE BLOCK PH2912062 SPRING PH2912063 ROD PH2912064 SET BLOCK PH2909065 TAIL COVER H2912/H2913 2-IN-1 NAILER/STAPLER...
- Page 13 H2913 PART BREAKDOWN H2912/H2913 2-IN-1 NAILER/STAPLER...
- Page 14 PH2913055 MAGAZINE PH2913056 BRACKET PH2913057 CAP SCREW PH2913058 SHAFT PH2913059 SET SCREW STAPLE GUIDE UNIT PH2913060A END CORE ASSY. PH2913061A PH2913062 CAP SCREW PH2913063 PUSHER PH2913064 SLIDE BLOCK PH2913065 SPRING PH2913066 ROD PH2913067 SET BLOCK PH2913068 TAIL COVER H2912/H2913 2-IN-1 NAILER/STAPLER...
-
Page 15: Troubleshooting
Tool runs slowly or has a loss of power. Fasteners frequently jam the tool. Tool does not fire. H2912/H2913 2-IN-1 NAILER/STAPLER CAUSE 1. O-rings in trigger valve housing are damaged. 1. Loose screws in housing. 2. Damaged O-ring. -
Page 16: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. -
Page 17: Warranty Card
14. Do you think your purchase represents good value? 15. Would you recommend Grizzly to a friend? 16. Would you allow us to use your name as a refer- ence for Grizzly customers in your area? Note: We never use names more than three times. 17.Comments:________________________________... - Page 18 Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT X Place Stamp Here...