For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progres- sion of symbols is described below.
Page 3
14. DO NOT OVERREACH. Keep proper footing and balance at all times. H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER 15. MAINTAIN TOOLS WITH CARE. 16. DISCONNECT TOOLS before ser- 17. REDUCE THE RISK OF UNINTEN- 18.
Page 4
Use this tool with respect and caution to lessen the possibility of operator or bystander injury. Ignoring this warn- ing may result in serious personal injury. H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER wear American National...
Page 5
We are pleased to provide this manual with the Model H2910. It was written to encourage safety considerations and guide you through general operating pro- cedures and maintenance. This manual represents our effort to produce the best documentation possible.
Compressed Air System The Model H2910 is designed to be oper- ated at 60-100 psi. Do not exceed the maximum operating pressure for your model. Before you use your new nailer, install the ⁄ " quick connect fitting that comes with the nailer.
Figure 2. Loading the nailer. H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER OPERATION Push the magazine cover forward until the magazine latch locks in place.
The jammed nail should now be visi- ble; remove it from the discharge area with needle nose pliers. Replace the nails. Push the magazine closed and snap the quick release latch back into operating position. H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER...
Page 9
As mentioned before, the best option is to install a filter/lubricator/regulator unit such as the Grizzly Model H2333 in your air line. Figure 5. Lubricating the nailer via air inlet. H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER...
Replace the rear cap assembly and tighten the 4 cap screws. 12. For more assistance, or to install a complete O-ring set, refer to the appropriate breakdown diagram in the back of this manual. H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER...
Page 11
H2910 PART BREAKDOWN H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER...
Page 12
PH2910048 CAP SCREW PH2910049 MAGAZINE PH2910050 NAIL GUIDE LINER PH2910051 SPRING PH2910052 PUSHER PH2910053 SET SCREW PH2910054 MAGAZINE COVER PH2910055 ROLLED PIN PH2910056 STOPPER PH2910057 MAGAZINE COVER PH2910059 SPRING H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER DESCRIPTION BUMP FIRE SWITCH...
Tool runs slowly or has a loss of power. Fasteners frequently jam the tool. Tool does not fire. H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER CAUSE 1. O-rings in trigger valve housing are damaged. 1. Loose screws in housing. 2. Damaged O-ring.
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance.
14. Do you think your purchase represents good value? 15. Would you recommend Grizzly to a friend? 16. Would you allow us to use your name as a refer- ence for Grizzly customers in your area? Note: We never use names more than three times. 17.Comments:________________________________...
Page 16
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT X Place Stamp Here...