Harman  TL2.6 Owner's Manual
Harman  TL2.6 Owner's Manual

Harman TL2.6 Owner's Manual

Non-catalytic, top load, wood burning room heater
Hide thumbs Also See for Harman TL2.6:

Advertisement

Owner's Manual

Installation and Operation

Model:
TL2.6
Non-Catalytic, Top Load,
Wood Burning Room Heater
Item #1-90-857000- Pedestal
# 1-90-858000 - Leg
Important operating and
maintenance instructions
included.
WaRNINg
PLEasE REad THIs ENTIRE MaNuaL
BEfORE INsTaLLaTION aNd usE Of THIs
WOOd-BuRNINg ROOM HEaTER.
f a I L u R E
INsTRuCTIONs COuLd REsuLT IN
PROPERTy daMagE, BOdILy INjuRy OR
EvEN dEaTH.
dO NOT sTORE OR usE gasOLINE OR OTHER
fLaMMaBLE vaPORs aNd LIquIds IN THE
vICINITy Of THIs OR aNy OTHER aPPLIaNCE.
• dO NOT OvERfIRE - If aNy ExTERNaL PaRT
sTaRTs TO gLOW, yOu aRE OvERfIRINg. CLOsE
aIR CONTROLs. OvERfIRINg WILL vOId yOuR
WaRRaNTy.
• COMPLy WITH aLL MINIMuM CLEaRaNCEs TO
COMBusTIBLEs as sPECIfIEd. faILuRE TO
COMPLy May CausE a HOusE fIRE.
CauTION
TEsTEd aNd aPPROvEd fOR usE WITH dRy,
sEasONEd CORdWOOd ONLy. dO NOT BuRN WET
OR gREEN WOOd. BuRNINg aNy OTHER TyPE Of
fuEL WILL vOId yOuR WaRRaNTy.
www.harmanstoves.com
dO NOT dIsCaRd THIs MaNuaL
Read, understand and
follow these instructions
for safe installation and
operation.
T O
f O L L O W
T H E s E
NOTICE
Leave this manual with
party responsible for use
and operation.
HOT, WILL CausE BuRNs.
dO NOT TOuCH gLass uNTIL IT Is COOLEd
NEvER aLLOW CHILdREN TO TOuCH gLass
kEEP CHILdREN aWay
CaREfuLLy suPERvIsE CHILdREN IN saME ROOM
as fIREPLaCE.
aLERT CHILdREN aNd aduLTs TO HazaRds Of HIgH
TEMPERaTuREs.
HIgH TEMPERaTuREs May IgNITE CLOTHINg OR
OTHER fLaMMaBLE MaTERIaLs.
kEEP CLOTHINg, fuRNITuRE, dRaPERIEs aNd OTHER
fLaMMaBLE MaTERIaLs aWay.
CHECk BuILdINg COdEs PRIOR TO INsTaLLaTION.
INsTaLLaTION MusT COMPLy WITH LOCaL, REgIONaL, sTaTE
aNd NaTIONaL COdEs aNd REguLaTIONs.
CONsuLT LOCaL BuILdINg, fIRE OffICIaLs OR auTHORITIEs
HavINg juRIsdICTION aBOuT REsTRICTIONs, INsTaLLaTION
INsPECTION, aNd PERMITs.
3-90-08570
WaRNINg
HOT suRfaCEs!
gLass aNd OTHER suRfaCEs aRE HOT
duRINg OPERaTION aNd COOL dOWN.
CauTION
Rev: #6
September, 2011

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Harman TL2.6 and is the answer not in the manual?

Questions and answers

Summary of Contents for Harman Harman TL2.6

  • Page 1: Installation And Operation

    Owner's Manual Installation and Operation Model: TL2.6 Non-Catalytic, Top Load, Wood Burning Room Heater Item #1-90-857000- Pedestal # 1-90-858000 - Leg NOTICE dO NOT dIsCaRd THIs MaNuaL • • • Important operating and Read, understand and Leave this manual with maintenance instructions follow these instructions party responsible for use...
  • Page 2 TL2.6 Woodburning stove Hearth & Home Technologies welcomes you to our tradition of excellence! By choosing a Harman appliance, you have become part of our commitment to meeting the heating needs of consumers with the most distinctive, powerful and responsible home heating products available. With it's durable steel-body construction, the TL2.6 features a heating capacity of 1800 to 2200 ft².
  • Page 3: Table Of Contents

    TL2.6 Woodburning stove TaBLE Of CONTENTs section 1: Listing and Code approvals section 8: Operating Instructions A. Appliance Certifications A. Fuel Specifications B. Mobile Home Approval B. General Operating Information C. Glass Specifications C. Burning as a Fireplace D. Electrical Rating D.
  • Page 4: Section 1: Listing And Code Approvals

    TL2.6 Woodburning stove Section 1 - Listing and Code Approvals a. appliance Certification E. BTu & Efficiency specifications Model: TL2.6 Woodburning Stove Particulate Emissions 3.7g/hr Avg Laboratory: OMNI-Test Laboratories, Inc. Rating: Report No. 135-S-30-2 *BTU Input: 11,300 - 32,700 / hr Type: Solid Fuel Room Heater / Wood Heating Capacity:...
  • Page 5: Section 2: Special Warnings And Notes

    TL2.6 Woodburning stove Section 2 - Special Warnings and Notes Carbon monoxide, referred to as CO, is a colorless, CO detectors are very sensitive and may sound an alarm odorless gas that is produced during combustion of wood for fumes other than CO or CO from sources other than and other fuels.
  • Page 6: Considerations

    TL2.6 Woodburning stove Section 3 - Getting Started a. design, Installation & Location B. fire safety Considerations Maintain the designated clearances to combustibles. Insulation must not touch the chimney. You must 1. appliance Location maintain the designated air space around the chim- Consideration must be given to safety, convenience, ney.
  • Page 7: Component Locator

    TL2.6 Woodburning stove C. Component Locations Top Load Door Top Load Opening Bypass Damper Control Handle Front Load Door Front Load Door Latch Air Control Ash Door Ash Door Latch d. flue direction Conversion The TL2.6 features a convertible flue collar for rear or top vent. Follow these instructions for changing the direction. First, remove both side shields by removing 2 tek screws each, and loosen 1/4-20 bolts with a 3/8"...
  • Page 8: Pre-Use Checklist

    TL2.6 Woodburning stove E. Pre- use Check List Place the appliance in a location near the WaRNINg final installation and follow the procedures below: INsPECT aPPLIaNCE aNd COMPONENTs fOR daMagE. daMagEd PaRTs May Open the appliance and remove all articles IMPaIR safE OPERaTION.
  • Page 9: Section 4: Dimensions & Clearances

    (185mm) 9.29" air kit Outside (236mm) air kit Weight 525 lbs The Harman TL2.6 meets the U.S. Environmental Flue Size 6 inch Protection Agency’s emission limits for wood heaters sold after July 1, 1990. Log Length Recommended 18" Average Emissions 3.7 Grams Per Hr.
  • Page 10: Clearances To Combustibles

    TL2.6 Woodburning stove B. Clearances To Combustibles vertical venting Configuration Location single-wall Pipe double-wall Pipe unit to side Wall 17" / 432 mm 15" / 381 mm unit to Back Wall 17" / 432 mm 15" / 381 mm vent Pipe to side Wall 27"...
  • Page 11 TL2.6 Woodburning stove CLEaRaNCE TO COMBusTIBLEs: Horizontal venting Configuration Location single-wall Pipe unit to side Wall 15" / 381 mm unit to Back Wall 15" / 381 mm vent Pipe to side Wall 25" / 635 mm Corner Installation Corner to adjacent Wall 14.5"...
  • Page 12: Floor Protection

    TL2.6 Woodburning stove C. floor Protection Requirements daNgER: The appliance pedestal or legs may not be removed for installation. Minimum Size floor protection (USA) is 50.6" Deep By 32.5" Wide. floor Protection Inches Millimeters Requirements Sides- USA /CANADA * Front- USA /CANADA * Rear- USA Rear- CANADA * Floor protection dimensions for the front and sides...
  • Page 13: Section 5: Chimneys And Venting

    TL2.6 Woodburning stove The Chimney Connector shall Not Pass Through an attic or Roof Section 5 - Chimneys and Venting space, Closet or similar Concealed space, a floor or Ceiling. a. draft space, closet or other concealed space, or through a floor or ceiling.
  • Page 14: The Chimney

    TL2.6 Woodburning stove Closest Non-combustible cover, one Combustible Minimum 2" (50mm) side only. If two covers are Material Clearance to Brick Hole with a minimum used, each must be mounted clearance of 18" (450 on non-combustible spacers Minimum 12" mm) between connector Liner at least 7/8"...
  • Page 15 TL2.6 Woodburning stove 1. Existing Masonry Chimneys If you plan on using a pre-existing masonry chimney, have it thoroughly inspected and cleaned. Any faults which make the chimney unsafe and unusable must be repaired prior to use. These can include improper height, structural defects, blockages, inadequate clearance to combustibles, unsealed openings into other rooms of the house, signs of creosote or smoke...
  • Page 16: Factory Built Chimney

    TL2.6 Woodburning stove Standard Ceiling Installation with Cathedral Ceiling Installation with Factory Built Chimney Factory Built Chimney Chimney Cap Storm Collar Chimney Sections Chimney Cap Roof Flashing Roof Radiation Roof Factory-Built Shield Radiation Metal Chimney Shield Attic Sealed Storm Collar Radiation Roof Flashing Shield...
  • Page 17 TL2.6 Woodburning stove Chimney Breach Fireplace Conversion with Non-Combustible Wall Minimum Clearance to Unprotected Ceiling 16" Chimney Connector Sealed at Thimble Flue Liner with Required Air Space Three Sheet Metal Airtight Screws per Joint of insulated Chimney Connector Clean-out Mantel and Trim Protection Damper Closed and Sealed with...
  • Page 18 TL2.6 Woodburning stove TL2.6 to Flue Fireplace Conversion (Minimum NFPA 211 Liner Connection) Flue Liner with Required Airtight Air Space insulated Clean-Out Stainless Steel Chimney Connector Must Extend to Flue Liner Minimum 8" Masonry Thickness in Front of Smoke Chamber Use Damper Adapter or Seal with Non-Combustible Material...
  • Page 19 TL2.6 Woodburning stove Full Relining Fireplace Conversion: Freestanding Appliance UL1777 Stainless Steel Liner System or Other approved lining system Follow liner manufacturer's instructions on insulation and support UL1777 Insulated Stainless Steel Flex Liner or Other Approved Lining System in Offsets. Listed Fireplace Trim Protection for Reduced Clearance Damper Plate Removed or Fastened...
  • Page 20 TL2.6 Woodburning stove Chimney Breach Fireplace Conversion with Combustible Wall Minimum Clearance from Chimney Connector to Unprotected Ceiling 16"** Flue Liner with Required Air Space Listed or Approved Thimble Assembly Combustible Wall 1" Clearance for Complexity Exterior Chimney or 2" Clearance for Interior Chimney Sheetrock Airtight...
  • Page 21: Mobile Home Installation

    TL2.6 Woodburning stove Section 6 - Mobile Homes a. Mobile Home Installation NOTE: The top sections of the chimney must be removable to allow a maximum clearance of 13.5 feet Mobile home approval - u.s. only. (411cm) from ground level for transportation purposes. dO NOT INsTaLL IN a MOBILE HOME IN CaNada.
  • Page 22: Section 7: Appliance Set-Up

    TL2.6 Woodburning stove Section 7 - Appliance Set-Up a. Outside air attachment B. Leveling the appliance Parts and Supplies Needed: Kit #1-10-856082, 1 Use metal shims for leveling with the pedestal base. piece of metal flexible pipe, 4" X needed length. 1 When the leg option is chosen, each leg has a Rodent Screen, and aluminum tape.
  • Page 23: Optional Blower Kit

    TL2.6 Woodburning stove d. Optional Blower Installation E. Brushed stainless Trim kit Option use ONLy Blower Part #1-00-856002 With This appliance. The optional blower kit installs easily to the rear of the TL2.6. First, remove the air jacket shield from the rear of the stove.
  • Page 24: Section 8: Operating Instructions

    TL2.6 Woodburning stove Section 8 - Operating Instructions B. general Operating Information CauTION: approved for use with wood fuel only. The use of any other fuel will void the product 1. draft Before you install and/or operate your warranty and may cause damage to the appliance wood stove, please read the entire contents of this and/or your home.
  • Page 25: Burning As A Fireplace

    TL2.6 Woodburning stove 3. grates d. The Combustion Process The unique grate system consists of one flat bottom grate, and two front andirons. The bottom grate has Combustion within the appliance is precisely slots which allow the ash to fall into the ash pan by controlled and is best explained in two parts.
  • Page 26: User Controls

    TL2.6 Woodburning stove E. user Controls For low burn, slide the air control to the left. For medium burns, use notches 1 to 2. Maximum heat is Two important controls - the damper bypass handle attained with the air control all the way to the right. Do and the air control lever regulate the operation and not burn the stove continuously at the maximum setting.
  • Page 27 TL2.6 Woodburning stove Providing you have the charcoal bed described, dIsPOsaL Of asHEs; close the bypass damper by pulling the handle toward ashes should be placed in a steel container with the front of the stove. This will begin the highly efficient a tight fitting lid.
  • Page 28: Section 9: Service & Maintenance

    TL2.6 Woodburning stove Section 9 - Serviceand Maintenance solid fuel burning space heaters must be cleaned regularly, as soot, ash and creosote may accumulate. Creosote- formation and Need for seasonal cleaning Removal; At least once per year, the stove, venting connectors and chimney should be thoroughly When wood is burned slowly, it produces tar cleaned.
  • Page 29: General Maintenance Procedures

    TL2.6 Woodburning stove B. general Maintenance Procedures 2. door glass • frequency: As needed / Weekly 1. ash Removal • By: User • frequency: As needed / Every day or two • By: User Whenever the view of the fire is obstructed, or weekly, clean the glass using a soft cloth dampened with Wear Leather gloves To Prevent skin Burns! standard household glass cleaner.
  • Page 30 TL2.6 Woodburning stove 3. firebox 5. Chimney Connector • frequency: As necessary / Yearly • frequency: As necessary / Yearly • By: User • By: Qualified Service Technician / User Cleaning the firebox and internal heat exchange At the end of the burn season, brush and clean surfaces is recommended to maintain thermal all sections of chimney connector pipe.
  • Page 31: Section 10: Reference Materials

    TL2.6 Woodburning stove Section 10 - reference Materials Save These Instructions 3-90-08570 Dry Seasoned Wood Only!
  • Page 32: Service Parts Listing(Pedestal)

    TL2.6 W/Pedestal service Parts Beginning Manufacturing date: sept 2011 Wood stove Ending Manufacturing date: active 1-90-857000-1 Part number list on following page. 01/12...
  • Page 33 TL2.6 W/Pedestal service Parts Beginning Manufacturing date: sept 2011 Ending Manufacturing date: active IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement stocked parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer. at depot ITEM dEsCRIPTION...
  • Page 34: Service Parts

    TL2.6 W/Pedestal service Parts Beginning Manufacturing date: sept 2011 Ending Manufacturing date: active IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement stocked parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer. at depot ITEM dEsCRIPTION...
  • Page 35: Service Parts Listing (Legs)

    TL2.6 w/Legs service Parts Beginning Manufacturing date: sept 2011 Wood stove Ending Manufacturing date: active 1-90-858000-1 Part number list on following page. 01/12...
  • Page 36 TL2.6 w/Legs service Parts Beginning Manufacturing date: sept 2011 Ending Manufacturing date: active IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement stocked parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer. at depot ITEM dEsCRIPTION...
  • Page 37 TL2.6 w/Legs service Parts Beginning Manufacturing date: sept 2011 Ending Manufacturing date: active IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement stocked parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer. at depot ITEM dEsCRIPTION...
  • Page 38: Epa Hang Tag

    Manufactured by: HeartH & HoMe tecHnologies, inc. Model: tl2.6 u.s. enviroMental Protection agency Meets EPA particulate matter (smoke) control requirements for noncatalytic wood heaters built on or after July 1, 1990. sMoKe grams Per Hour efficiency 100% Wood heaters with higher efficiencies cost less to operate. Heat outPut 11,300 to 32,700 btu use this to choose the right size appliance for your needs.
  • Page 39: Warranty Policy

    Hearth & Home Technologies Inc. LIMITED LIFETIME WARRANTY Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer. WARRANTY COVERAGE: HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance...
  • Page 40 WARRANTY CONDITIONS: • This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of HHT authorized dealers is available on the HHT branded websites. • This warranty is only valid while the HHT appliance remains at the site of original installation. •...
  • Page 41 TL2.6 Woodburning stove service & Maintenance Log Date Of Service Performed By Description Of Service Dry Seasoned Wood Only! 3-90-08570 Save These Instructions...
  • Page 44 At Harman, we build each product to a standard, not a price. This powerful heating appliance boasts uncompromising attention to detail and helps preserve our planet by using environmentally responsible fuels. (Signature of Boxer) Your premium quality hearth product designed and assembled by the experienced and skilled members at Harman in Halifax, PA, USA.

Table of Contents