Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Heartway Medical Products S9
Summary of Contents for Heartway Medical Products S9
- Page 1 USERS MANUAL HEARTWAY MEDICAL PRODUCTS CO., LTD. Part no:70030170...
-
Page 2: Table Of Contents
CONTENTS 1. Techni cal S peci fi cat i on ……………........... …………… . 3 2. S a f et y In s t r u c t i o n … … …… … …… ……… … …… … …… … . … … …… … …… .. 4 ~ 6 3. -
Page 3: Techni Cal S Peci Fi Cat I On
TECHNICAL SPECIFICATIONS... -
Page 4: Safety Instruction
SAFETY INSTRUCTION OPERATION OF SCOOTER To prevent injury to yourself or others, always ensure that the power is switched off when getting on or off of the scooter. Always check that the drive wheels are engaged (drive mode) before driving. Engage Free Wheel (Fig.1) - Page 5 Emergency Brake (Optional) General Always use a seat belt, and keep your feet on the scooter all the time. Do not over load the scooter with it’s maximum weight capacity of 135kg (300 lbs) Do not attempt to lift or move a power scooter by any of its removable parts. Personal injury and damage to the power chair may result.
- Page 6 The United States Food and drug Administration (FDA) suggests that the following statement be incorporated to the user’s manual for all power scooter like the S9. Power wheelchairs and motorized scooters (in this section, both will be referred to as powered wheelchairs) may as...
- Page 7 ENVIRONMENTAL CONDITIONS Environmental conditions may affect the safety and performance of your power scooter. Water and extreme temperatures are the main elements that can cause damage and affect performance. A) Rain, Sleet and Snow If exposed to water, your power scooter is susceptible to damage to electronic or mechanical components.
-
Page 8: Warranty
WARRANTY Quality/ Warranty Declaration Products are to be fit for purpose and of excellent quality and performance. For valid warranty claims Heartway will, at their discretion, replace/ repair/ refund items mutually agreed to be defective. Heartway’s warranty as following: (1) Frame: two year limited warranty (2) Electronic Components and Charger: one year limited warranty. -
Page 9: Assembly Instruction
ASSEMBLY INSTRUCTION It is very easy to assemble your S9 scooter. Please follow the procedure below. 1. Tiller Positioning Press down the lever, fold the tiller up to vertical position and let it lock into your preferred position. (See Fig 4 & 5) (Fig.4) -
Page 10: Adjustment For Seating Comfort
3. Installing the Batteries Remove three screws as shown on Fig.7 and take off the cover. Connect both battery cables probably (﹢/ ﹣ pole ,Red is positive, black is negative) Connected (Fig.7) (Fig.8) ADJUSTMENTS FOR SEATING COMFORT A. Armrest Position Adjustment Turn the round plate and adjust to your position. - Page 11 B. Seat Rotation and Position Adjustment B-1: Seat Rotation Adjustment → Press the seat swivel lever downward. → Rotate your seat by clockwise or counter-clockwise direction. (Fig.10) (Fig.11) B-2: Seat Position Adjustment → Push the seat adjust lever upwards. → slide your seat backward or forward to your desired position →...
-
Page 12: Control Panel Layout
OPERATION AND CONTROL PANEL 1. Control Panel Layout LCD（Liquid Crystal Display）Power Scooter Control Panel, TN Type LCD Screen Indications Indications Right Indicator Left Indicator Headlight Position Light Parking Indicator Warning Indicator Left Indicator control Right Indicator control SET button Parking lamp control Position Light control MODE button High / Low speed control... -
Page 13: Function
2. Functions 2-1 Function Descriptions SPECIFICATION FUNCTION “C” / “F” modes Temperature Hour / Minute display and setting Clock ODO (99999 max), TRIP (999.9 max) Odometer Sum of distance and time Trip Meter 7 Segment display (2 1/2 digits +1 decimal) Speedometer “km/h”... -
Page 14: B U T T O N S & I N D I C A T O R
2-2 Buttons & Indicators ITEM DESCRIPTION Function & Adjustment Buttons: Left-Indicator (Green) Right- Indicator (Green) LED Indicators Position Light (Amber) Headlight (Blue) Warning Indicator (Red) Parking Indicator (Red) LCD Backlight Illumination: 700 mcd min (Orange color) CON1: 20PIN Connecter 3. Usage Conditions ITEM SPECIFICATION DC 24 V... -
Page 15: C H A R A C T E R I S T I C
4. Characteristics Test General Characteristic Performance Test (20 5℃) Hardware Circuit: ITEM SPECIFICATION RESULT (n = ) Lowest Operation Voltage 16V max Dynamic: 200 mA max (backlight and all of LED illuminated) Consuming Current = 24.0V) Static: 5 mA max (Key Off status) 5. -
Page 16: Clock
ITEM DESCRIPTIONS Press for more than 2 seconds to enter Setting Mode Setting-Mode, and the backlight illuminates in the meantime. (Unit Switch) to switch C / F. When “C” or “F” flashing, press Under Setting-Mode, when 1) idle for more than 20 seconds, Exit 2) press for more than 2 seconds,... -
Page 17: O D O M E T E
DESCRIPTIONS ITEM Press for longer than 2 seconds to enter Setting-Mode, the backlight illuminates in the meantime. 1) When “Hour” digit is flashing, press to increase the number, and into “Min” setting mode. then press Setting Mode 2) When “Min” digit is flashing, press to increase the number, then (Time Switch) back to “Hour”... - Page 18 DESCRIPTIONS ITEM Press switching to『ODO』mode km/h ODO Mode Display Range:00000~99999 When the total distance ran to 99999km or 62149mile (99999÷1.609mile), the digits will be reset to zero “00000”. Press switching to『TRIP』mode TRIP Mode Display Range:0.0~999.9 When the distance goes to 999.9, the counter will stop, please press for 3 seconds to reset to zero “0.0”.
-
Page 19: S P E E D O M E T E
5-4. Speedometer DESCRIPTIONS ITEM OptoCoupler sensor detects the signal and then converts into a speed value. Operation Features When drive shaft runs at 2100 rpm, speedometer will display “60km/h”. +15~20% Tolerance 0.0 ~ 30.0 Display Rate：0.5 Digits range Press for longer than 2 seconds to enter Setting-Mode, backlight illuminates in the meantime. - Page 20 DESCRIPTIONS ITEM to enter 『SPEED』mode Press km/h 「km/h」means the speed is counted as kilometer. 「mph」means the speed is counted as mile. When SPEED was set on “km/h” or “mph”, even the waiting screen is not SPEED mode, LCD will switch to SPEED mode when WIP (accelerator) is Working Mode acting, and back to previous waiting screen automatically once WIP (accelerator) stopped.
-
Page 21: Hi Gh/ Lo W S P E Ed & Tu Rn Ind I C At Or
5-5. High/Low Speed & Turn Indicators DESCRIPTIONS ITEM Press to switch High / Low speed. (*Control signals: TRN, with memory storage) Operation Features Take exterior turn-switch as determinant signal (*Control signals: TRN) High Speed: Symbols of Status Low Speed: Turn Status: (Flashing) Flicker Frequency... -
Page 22: Power Indication
5-6. Power Indication DESCRIPTIONS ITEM Remaining Scale Bar Capacity (%) Battery Remaining Capacity is f and icon lashing Warning LED is flashing Flicker 2 seconds Frequency The scale status only decrease, won’t increase. When the remaining capacity was less than 30%, warning sound (“Bi-Bi” - two Operation short sounds) act at 1 second intervals. - Page 23 DESCRIPTIONS ITEM Remaining Scale Bar Capacity (%) Charge Indication Increase 0.5 second Frequency Scale status only decrease, won’t increase. Take the PIN3(CH3) of charger as the determinant signal, when CH3 is grounded (L), Operation LCD will enter Charging-Mode, not limited by “KEY ON” or “KEY OFF”. Character ...
- Page 24 5-7. Headlight DESCRIPTIONS ITEM Take exterior headlight switch as determinant signal. Operation Feature Press button to switch on/off LED LCD backlights will be turned on/off when headlight switching on/off. When motor is resting, power modulate down to 30% (Headlight) Power Saving Mode ...
-
Page 25: Headli Ght & Position Li Ght
5-9. Brake and Reversing Light DESCRIPTIONS ITEM Take exterior WIP / RBK / Headlight / Back-up lamps switch as determinant Operation Feature signal. Judge to be “Brake” or “Handbrake” state, when WIP (accelerator) signal changed from actuated to neural position, and will recover automatically Control Mode after 3 seconds (Brake-Light Mode). -
Page 26: Direction Indicators
5-10. Direction Indicators and Parking Light DESCRIPTIONS ITEM Operation Take exterior left-right direction indicators and parking lamp switch as the determinant signal. Feature (Control Mode) Left-direction lamp Press button once, the left-indicator start to flash, and the warning sound act simultaneously, then press button again to switch off the indicator. -
Page 27: Malfunction Messages
5-11. Malfunction Messages DESCRIPTIONS ITEM Take the connector pin (KEY) of controller as determinant signal, then converts Operation Feature it into digital code. When the controller send out an error message, warning indicator start flashing with controller signal at same time, the “Error message code” will show on LCD screen. -
Page 28: Power-On-Self-Test
5-12. Power-On-Self-Test DESCRIPTIONS ITEM When scooter power on, the control panel will take a self-test first; the backlight Initial Status and all LCD segments will be tuned on for 3 seconds, then switch automatically to the default working mode. When press buttons, the LCD backlight will illuminate LCD Backlight and turn off automatically if the button doesn’t be operated for longer than 5...