imagistics im7520 User Manual

Copy operations

Table of Contents

Quick Links

Download this manual

www.imagistics.com

im7520

im6020

User's Guide

Copy Operations

Table of Contents

Chapters

Table of Contents

Troubleshooting

Summary of Contents for imagistics im7520

Page 1 User's Guide Copy Operations...
Page 2 Replacing Toner Cartridges and Staples and Emptying Dust Boxes...
Page 3: Replacing The Toner Cartridge
“Toner Cartridge needs to be replaced.” appears. When the message“Replace the toner” appears, the machine is stopped. When the toner is empty, the warning message shown below appears and copies can no longer be made. im7520/im6020...
Page 4 When the toner is empty, the screen shown below appears. Touch to display the message enlarged. 7 WARNING Handling toner and the toner cartridges Do not throw toner or the toner cartridge into a fire. Toner expelled from the fire may cause burns. im7520/im6020...
Page 5 To replace the toner cartridge Open the toner cartridge door. Pull out the cartridge holder. While pulling the toner- cartridge-securing lever toward you, pull the car- tridge holder out toward you as far as possible. im7520/im6020...
Page 6 The toner within the toner cartridge may have become com- pacted. If it has, be sure to shake the toner cartridge until the toner is mostly broken up before in- stalling the cartridge. Remove the cover from the toner cartridge. im7520/im6020...
Page 7 With the label at the end of the toner cartridge facing up, insert the bot- tom of the cartridge into the slot in the cartridge holder. Return the cartridge holder to its original po- sition, and then close the toner cartridge door. im7520/im6020...
Page 8: Replacing The Staples
Replacing Toner Cartridges and Staples and Emptying Dust Boxes Replacing the Staples When finisher 9202/9204 is installed and is about to run out of staples, the message shown below appears. Display in Enlarge Display Mode im7520/im6020...
Page 9 “Replace Staple Cartridge 1” or “Replace Staple Cartridge 2” ap- pears. To replace the staple cartridge for finisher 9202 Open the finisher door. Pull out the stacker unit. – Hold the stacker unit handle, and then slowly pull out the stacker unit as far as possible. im7520/im6020...
Page 10 Install the new staple cartridge. – Push up the staple cartridge, and then check that the car- tridge is securely in- stalled. Return the stacker unit to its original position. im7520/im6020...
Page 11 Replacing Toner Cartridges and Staples and Emptying Dust Boxes Close the finisher door. 9-10 im7520/im6020...
Page 12 Replacing Toner Cartridges and Staples and Emptying Dust Boxes To replace the staple cartridge for finisher 9204 Open the finisher door. Pull out the stacker unit. – Hold the stacker unit handle, and then slowly pull out the stacker unit as far as possible. im7520/im6020 9-11...
Page 13 While lifting the lever on the staple car- tridge, pull the car- tridge toward you to remove it. – Remove the staple cartridge by guiding it along the rails. Remove the empty car- tridge case from the sta- ple cartridge. 9-12 im7520/im6020...
Page 14 Install the staple cartridge. – Place the staple car- tridge on the rails, and then guide it back to its original position. – Push down the sta- ple cartridge, and then check that the cartridge is securely installed. im7520/im6020 9-13...
Page 15 Replacing Toner Cartridges and Staples and Emptying Dust Boxes Return the stacker unit to its original position. Close the finisher door. Reminder Do not remove the remaining staples, otherwise the machine will not be able staple after the cartridge is replaced. 9-14 im7520/im6020...
Page 16: Emptying The Dust Boxes
Emptying the Dust Boxes To empty the dust box of the punch kit If the punch dust box in punch kit im9220010 installed on finisher 9202/9204 becomes full, the message shown below appears. Display in Enlarge Display Mode im7520/im6020 9-15...
Page 17 Replacing Toner Cartridges and Staples and Emptying Dust Boxes Open the finisher door. Pull out the punch dust box. Empty the punch dust box. 9-16 im7520/im6020...
Page 18 Close the finisher door. To empty the dust box of the Z-folding unit If the punch dust box in Z-folding unit 9263 installed on finisher 92029202/ 9204 becomes full, the message shown below appears. im7520/im6020 9-17...
Page 19 Replacing Toner Cartridges and Staples and Emptying Dust Boxes Display in Enlarge Display Mode Open the finisher door. 9-18 im7520/im6020...
Page 20 Replacing Toner Cartridges and Staples and Emptying Dust Boxes Pull out the punch dust box. Empty the punch dust box. Install the punch dust box into its original posi- tion. im7520/im6020 9-19...
Page 21 Replacing Toner Cartridges and Staples and Emptying Dust Boxes Close the finisher door. 9-20 im7520/im6020...
Page 22 Care of the Machine...
Page 23: Care Of The Machine
Reminder Be sure to turn off the machine (set the power switch to “o”) before cleaning it. Never use solvents, such as benzene or thinner, to clean the main body. 10-2 im7520/im6020...
Page 24 Never use solvents, such as benzene or thinner, to clean the original glass. Left Partition Glass Clean the left partition glass by wiping it with a soft, dry cloth. Reminder Never use solvents, such as benzene or thinner, to clean the left partition glass. im7520/im6020 10-3...
Page 25: Adf Platen Guide Cover
ADF platen guide cover Clean the ADF platen guide cover by wiping it with a soft, dry cloth. Reminder Never use solvents, such as benzene or thinner, to clean the ADF platen guide cover. 10-4 im7520/im6020...
Page 26 Care of the Machine Paper Take-Up Roller Clean the paper take-up rollers by wiping them with a soft, dry cloth. Reminder Never use solvents, such as benzene or thinner, to clean the paper take- up roller. im7520/im6020 10-5...
Page 27 % To print the list of counters, touch [Print], select the paper size, and then press the [Start] key. Touch [Close]. The Basic screen appears again. Note The list of counters can be displayed even while the machine is copying or printing. 10-6 im7520/im6020...
Page 28 Care of the Machine 10.3 When the Message “Preventive maintenance time.” Appears If the message “Preventive maintenance time.” appears, contact your tech- nical representative and request a periodic maintenance inspection. im7520/im6020 10-7...
Page 30 Managing Jobs (Job List)
Page 31: Overview Of The Job List Screen
- From the Job List screen, the following tabs for various specific functions can be displayed. – Print: Lists print jobs for copying and computer printing – Scan: Lists scanner transmission jobs – RX: User Box Lists print jobs saved in boxes 11-2 im7520/im6020...
Page 32: Active Jobs
- The function of each button in the Job List screens is described below. A selected button indicates which job list is currently displayed. [Held Jobs], [Active Jobs], [Increase Priority], [Delete], and [Check Job] appear in the Current Jobs list on the Print tab. im7520/im6020 11-3...
Page 33 [Scan] Displays the Scan tab of the Job List screen. For more details, refer to the Network scanner volume of the im7520/im6020 User’s Guide. [RX/User Box] Displays the RX/User Box tab of the Job List screen. For more details, refer to the Facsimile Operations of the im7520/im6020 User’s Guide.
Page 34 Displays the number of pages in the original. # of Sets Displays the specified number of pages to be printed. Result (Job History list only) Displays the result of the operation (Job Complete, Error Cleared, Deleted by User, Mode cancelled from conflict) im7520/im6020 11-5...
Page 35: Performing Operations On Jobs
] until the desired job is displayed. – If an incorrect job was selected, select a different job or touch the button for the selected job again to deselect it. A message requesting confirmation to delete the job appears. 11-6 im7520/im6020...
Page 36 The screen that was displayed before [Job List] was touched appears again. Note If user authentication settings have been applied and the machine is set so that jobs cannot be deleted by other users, the job is not deleted. im7520/im6020 11-7...
Page 37: Job Details
To finish checking the settings, touch [Close] or [Exit], or press the [Re- set] key. – To return to the Job List screen, touch [Close]. – To return to the Basic screen, touch [Exit] or press the [Reset] key. 11-8 im7520/im6020...
Page 38: Job History
Name, Time Stored, # of pgs., # of Sets, Output Tray, File Name Displayed only for jobs in the Current Jobs list Displayed only for jobs in the Job History list Displayed only for Current Jobs transmitted to multiple recipients im7520/im6020 11-9...
Page 39 To return to the Job List screen, touch [Close]. – To return to the Basic screen, touch [Exit] or press the [Reset] key. Detail To delete a queued job or job being performed, touch [Delete] in the Check Detail screen. 11-10 im7520/im6020...
Page 40 “To print a stored job” on page 11-15. To give priority for output to a job, touch [Increase Priority] in the Active Jobs list. For more details, refer to “To increase priority for printing” on page 11-18. im7520/im6020 11-11...
Page 41 Deleted Jobs: Displays only jobs that were deleted before they were finished – Finished Jobs: Displays only jobs that were correctly completed – Active Jobs: Displays all jobs The history of jobs of the selected type is displayed. 11-12 im7520/im6020...
Page 42 If an incorrect job was selected, touch the button for the selected job again to deselect it. How is the printing of a sample copy stopped? % Touch [Stop]. Touch [OK]. – After the single sample copy is printed, check the print result. im7520/im6020 11-13...
Page 43 To exit the Release Held Job screen and return to the Active Jobs list in the Current Jobs list, touch [Cancel]. Detail To change the settings, touch [Change setting] in the Release Held Job screen. For details, refer to “To print a stored job” below. 11-14 im7520/im6020...
Page 44 To quit removing a stored job, touch [Cancel]. – To change the specified copy settings, continue with step 4. – To continue without changing the specified copy settings, skip to step 8. Touch [Normal Print]. [Change Setting] appears. im7520/im6020 11-15...
Page 45 The screen for the selected copy setting appears. Can the copy settings be changed? % The following copy settings can be specified after a sample copy is printed. # of Sets, 1-Sided/2-Sided, Finishing, Folding, Page Margin, Stamp/Overlay, Cover Mode, Insert Sheet, Chapters 11-16 im7520/im6020...
Page 46 11-13. In the Release Held Job screen, touch [OK]. The stored job appears in the Active Jobs list and is printed. How is the removal of a job from the Held Jobs list stopped? % Touch [Cancel]. im7520/im6020 11-17...
Page 47 If the job to be given priority is not displayed, touch [ ] and [ until the desired job is displayed. – If an incorrect job was selected, select a different job or touch the button for the selected job again to deselect it. 11-18 im7520/im6020...
Page 48 Managing Jobs (Job List) The selected job moves to the top of the list and printing of the job be- gins. How is the changing of the output priority stopped? % Touch [Cancel]. im7520/im6020 11-19...
Page 50 Utility...
Page 51: Overview Of Utility Mode
12-11 sonal User Box User Setting [1] System Set- [1] Language p. 12-14 p. 12-14 ting ( Selection [2] Measurement Unit Setting [3] Paper Tray [1] Paper Type Paper Type Setting Paper Size [2] Auto Tray Select Setting 12-2 im7520/im6020...
Page 52 [1] Sub Screen p. 12-19 ting ( Display ON/OFF [2] Scan Basic Default Tab Screen Default Seeing Program Default Address Book Default Index Address Type Symbol Display [4] Copy Screen Copy Operat- ing Screen [3] Initial Setting p. 12-20 im7520/im6020 12-3...
Page 53 Original Direction Spool Print Jobs in HDD before RIP A4/A3 ↔ LTR/ LGR Auto Switch Banner Setting Admin. Number Text Density [2] Paper Paper Tray Setting Default Paper Size 2-Sided Print Bind Direction Staple Hole-Punch Banner Paper Tray 12-4 im7520/im6020...
Page 54: Job Settings
[4] Select Time for Power Save [5] Password for Non-Business Hours [6] Restrict User [1] Restrict Access to Access Saved Program Jobs [2] Delete Saved Program Jobs [3] Restrict Access Changing Job to Job Settings Priority Deleting Other User’s Jobs im7520/im6020 12-5...
Page 55 [5] Punch Resist Loop Size [4] Z-Fold Posi- [1] 1st Z-Folded tion Adjustment Position [2] 2nd Z-Fold- ed Position [5] Tri-Fold Position [6] 2 Position Staple [7] Cover Sheet Tray Size [6] Scanner [1] Leading Edge Adjustment*** Adjustment*** [2] Centering*** 12-6 im7520/im6020...
Page 56 12-32 [2] FTP [3] SMB [4] User Box [2] Group [3] Program [4] Subject/ [1] Subject Text (for E-mail) [2] Text [3] User Box [1] Public/Per- sonal User Box [4] One-Touch [1] Address Registration List Book List im7520/im6020 12-7...
Page 57 [4] IPP Setting [5] FTP Setting [6] SMB Setting [7] AppleTalk Setting [8] LDAP [1] Enabling Setting LDAP [2] Setting Up LDAP [9] E-Mail [1] E-Mail TX Setting (SMTP) [2] E-Mail RX (POP) [0] Detail [1] Device Setting Setting 12-8 im7520/im6020...
Page 58 [8] System [1] IS OpenAPI Access Setting Connection Setting p. 12-37 Port No. Authentication [9] Security Set- [1] Administra- p. 12-37 ting ( tor Password [2] User Box Admin. Setting [3] Administrator Security Level [4] Security Password Details Rules im7520/im6020 12-9...
Page 59 [9] Security Set- [4] Security Print Data (Cont.) ting (Cont.) Details (Cont.) Capture [5] HDD Setting [1] Check HDD Capacity [2] Delete Un- used User Box [3] Delete Secure Print Documents [5] Overwrite All Data [6] HDD Lock Password 12-10 im7520/im6020...
Page 60: Selecting A Destination Register
Registration]. One-Touch Registration Parameter Description Address Book Register recipients for scanning. For details, refer to the Network Scanner Operations of the im7520/im6020 User’s Group Guide. Program Subject/Text (for E-mail) Note If user authentication has been set to “ON”, [1 One-Touch Registration] does not appear when no user has logged on.
Page 61 Touch [1 One-Touch Registration]. – An item can also be selected by pressing the key in the keypad for the number beside the desired button. For “One-Touch Registration” press the [1] key in the keypad. The One-Touch Registration screen appears. 12-12 im7520/im6020...
Page 62 To quit specifying the Utility mode setting, touch [Exit] in the sub display area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode by touching [Close] in each screen until the screen for the Copy, Scan or Box mode appears. im7520/im6020 12-13...
Page 63: Specifying User Settings
• Standard Size 2: Select when loading paper of the following sizes: A4 w , A5 v, F4. • Custom Size: Select when using cus- tom-sized paper. • Oversized Paper: Select when paper larger than a standard size is being used. 12-14 im7520/im6020...
Page 64 Tray 1/ Tray 2/ Tray 3/ lists, such as the sales counter Tray 4/ Bypass tray/ LCT Note To load paper of a different size into the tray 1 and 2 and the LCT, contact your technical representative. im7520/im6020 12-15...
Page 65: Reset Setting
(However, even if “OFF” is selected, the destination is cleared.) 12-16 im7520/im6020...
Page 66: Administrator Setting Screen
[Power Save Setting] appears only if the “Administrator Security Level” parameter (displayed from the Administrator Setting screen) is set to “Level 1” or “Level 2”. Detail For details on the “Administrator Security Level” parameter, refer to “Se- curity Setting” on page 12-37. im7520/im6020 12-17...
Page 67 Daylight Savings Time Setting Description Settings (Default set- tings are underlined.) Specify whether or not the machine’s internal clock observes day- ON/ OFF light saving time, and set the daylight saving time. 1 to 150 minutes: 60 minutes 12-18 im7520/im6020...
Page 68: Display Setting
A list of the jobs that are being performed is displayed. Scan Basic Screen Default Setting Parameter Description Default Tab Specify settings for scanning. For details, refer to the Network Scan- ner Operations of the im7520/im6020 User’s Guide. Program Default Address Book Default In- Address Type Symbol Display Copy Screen...
Page 69 To change the default settings for Scan mode , press the [Scan] key, en- ter Utility mode, and then select a setting for this parameter. Detail For details on the default settings and the factory default settings, refer to “Automatically Canceling the Settings (Automatic Panel Reset)” on page 2-27. 12-20 im7520/im6020...
Page 70: Copier Setting
• Default Tray: The paper tray set as the default is se- lected. Select Tray for Insert Select the default paper tray loaded with Tray1/ Tray2/ Tray3/ Sheet paper for the cover pages and Insert Tray4/ Bypass tray/ LCT/ sheets. im7520/im6020 12-21...
Page 71 [Print Jobs During Copy Operation] appear only if the “Administrator Se- curity Level” parameter (displayed from the Administrator Setting screen) is set to “Level 2”. Detail For details on the “Administrator Security Level” parameter, refer to “Se- curity Setting” on page 12-37. 12-22 im7520/im6020...
Page 72: Scanner Setting
Parameter Description Black Compression Specify settings for scanning. For details, refer to the Network Scan- Level ner Operations of the im7520/im6020 User’s Guide. Printer Setting Parameter Description Basic Setting Specify settings for printing. For details, refer to the im6020020 Us- er’s Guide.
Page 73 Touch [2 User Setting]. – An item can also be selected by pressing the key in the keypad for the number beside the desired button. For “2 User Setting”, press the [2] key in the keypad. The User Setting screen appears. 12-24 im7520/im6020...
Page 74 To quit specifying the User mode setting, touch [Exit] in the sub display area or press the [Utility/Counter] key. Otherwise, cancel the User mode by touching [Close] in each screen until the screen for the Copy, Scan or Box mode appears. im7520/im6020 12-25...
Page 75: Specifying Administrator Settings
Specify settings for printing. For details, refer to the im6020020 Us- tings er’s Guide. Exit Tray Setting Select the copy exit tray for each type of Copy: Main Tray/ Sub job (copies, printouts and reports). Tray Printer: Main Tray/ Sub Tray Reports Print: Main Tray/ Sub Tray 12-26 im7520/im6020...
Page 76 Password for Non-Busi- Select whether or not the machine can ON/ OFF ness Hours be used after a password is entered when the machine has been turned off by the weekly timer. im7520/im6020 12-27...
Page 77 Jobs Register- Select whether or not to allow registered Allow/ Restrict ing and recipients to be changed. Changing Addresses Changing Select whether or not to allow stored Allow/ Restrict Zoom zoom ratios to be changed. Ratio 12-28 im7520/im6020...
Page 78: Expert Adjustment
2nd-Side Size Adjust- The 2nd-side size can be adjusted for Tray 1 to 4, Bypass, LCT ment each tray. key: No Selection/ – – – 0.1%/ 0.2%/ 0.3% im7520/im6020 12-29...
Page 79 • Corner Staple & Fold (9204) Cover Adjust the cover sheet tray size if the pa- — Sheet Tray per cannot be detected correctly or if Size one side of the cover sheet feeder is ad- justed. (9262) 12-30 im7520/im6020...
Page 80 Original Glass Original Size Detect Specify the paper standards for AB series/ Inch series/ detecting paper from the original A series/ Full size glass. ADF Original Size Detect Specify the paper standards for detecting paper in the ADF. im7520/im6020 12-31...
Page 81: Administrator/Machine Setting
Specify settings for using the boxes. For details, refer to the Box Op- erations of the im7520/im6020 User’s Guide. One-Touch Registration For details, refer to the Network Scanner Operations, Facsimile Op- List erations and Box Operations of the im7520/im6020 User’s Guide. 12-32 im7520/im6020...
Page 82: Authentication Method
Counters Assigned for Users ”parameters are not available if “User Au- thentication” is set to “OFF” and “Account Track” is set to “OFF”. When “# of Counters Assigned for Users” is set to “50”, 950 accounts can be registered. im7520/im6020 12-33...
Page 83 If printing is permitted, prints are counted for public us- ers. Counter List Description The user and account track counters can be printed. Detail [Counter List] does not appear if “Public User Access” is set to “OFF” and “Account Track” is set to “OFF”. 12-34 im7520/im6020...
Page 84: Network Setting
Utility Network Setting Parameter Description Network Setting Specify settings for using the network. For details, refer to the Net- work Scanner Operations of the im7520/im6020 User’s Guide. TCP/IP Setting NetWare Set IPP Setting FTP Setting SMB Setting AppleTalk Setting LDAP Setting...
Page 85 [Tri-Fold Printed Side Selection] is available only if optional finisher 9204 is installed. Printer Setting Parameter Description Local I/F Timeout Specify settings for printing. For details, refer to the im6020020 Us- er’s Guide. Note [7 Printer Setting] appears only if optional printer controller im6020020 is installed. 12-36 im7520/im6020...
Page 86: System Connection
The administrator password used to specify the Administrator mode 12345678 settings can be changed. User Box Admin. Setting Description Specify settings for using boxes. For details, refer to the Box Operations of the im7520/im6020 User’s Guide. Administrator Security Level Description Settings (Default set- tings are underlined.)
Page 87 HDD Setting Parameter Description Check HDD Capacity Specify settings for using boxes. For details, refer to the Box Oper- ations of the im7520/im6020 User’s Guide. Delete Unused User Box Delete Secure Print Doc- uments Overwrite All Data HDD Lock Password...
Page 88 Utility/Counter Touch [3 Administrator Setting]. – An item can also be selected by pressing the key in the keypad for the number beside the desired button. For “Administrator Setting”, press the [3] key in the keypad. im7520/im6020 12-39...
Page 89 For details on typing in text, refer to “Entering Text” on page 13-2. The Administrator Setting screen appears. Note To quit specifying the Utility mode setting, touch [Exit] in the sub display area or press the [Utility/Counter] key. Otherwise, touch [Close] in each screen until the desired screen appears. 12-40 im7520/im6020...
Page 90: Adjusting The Printer
Touch [3 Printer Adjustment]. The Printer Adjustment screen appears. Touch [1 Leading Edge Adjustment]. The Leading Edge Adjustment screen appears. Touch the button for the paper type to be set. Touch [Test Copy]. The Test Copy screen appears. im7520/im6020 12-41...
Page 91 Repeat steps 7 through 11 until the desired print results are achieved. Touch [OK]. – To cancel changes to the settings, touch [Cancel]. The print position is adjusted. Note Enter the value by mm using the keypad. Refer to the conversion rate be- low. 1 in. = 25.4 mm 12-42 im7520/im6020...
Page 92 Touch [3 Printer Adjustment]. The Printer Adjustment screen appears. Touch [2 Centering]. The Centering screen appears. Touch [Test Copy]. The Test Copy screen appears. Press the [Start] key. A test pattern is printed. Touch [Close]. The Centering screen appears. im7520/im6020 12-43...
Page 93 Repeat steps 6 through 10 until the desired print results are achieved. Touch [OK]. – To cancel changes to the settings, touch [Cancel]. The print position is adjusted. Note Enter the value by mm using the keypad. Refer to the conversion rate be- low. 1 in. = 25.4 mm 12-44 im7520/im6020...
Page 94: Adjusting The Finisher
Touch [7 Expert Adjustment]. The Expert Adjustment screen appears. Touch [5 Finisher Adjustment]. The Finisher Adjustment screen appears. Touch [1 Center Staple Position]. The Center Staple Position screen appears. Touch the button for the paper size to be set. im7520/im6020 12-45...
Page 95 12.8 mm). – To scroll through the values quickly, touch [+] or [–] continuous- Repeat steps 6 through 11 until the desired print results are achieved. Touch [OK]. – To cancel changes to the settings, touch [Cancel] . 12-46 im7520/im6020...
Page 96 The Expert Adjustment screen appears. Touch [5 Finisher Adjustment]. The Finisher Adjustment screen appears. Touch [2 Half-Fold Position]. The Half-Fold Position screen appears. Touch the button for the paper size to be set. Touch [Test Copy]. The Test Copy screen appears. im7520/im6020 12-47...
Page 97 0.1 mm and 12.8 mm). – To scroll through the values quickly, touch [+] or [–] continuous- Repeat steps 6 through 11 until the desired print results achieved. Touch [OK]. – To cancel changes to the settings, touch [Cancel] . 12-48 im7520/im6020...
Page 98 Touch [7 Expert Adjustment]. The Expert Adjustment screen appears. Touch [5 Finisher Adjustment]. The Finisher Adjustment screen appears. Touch [3 Punch Adjustment]. The Punch Adjustment screen appears. Touch [1 Punch Vertical Position]. The Punch Vertical Position screen appears. im7520/im6020 12-49...
Page 99 Check the sample copy for the punch positions and for the center of the paper. If the desire print results are not achieved, change the adjustment val- – If the punch positions are too far above the center of the paper, touch [+] (between 0.1 mm and 5.0 mm). 12-50 im7520/im6020...
Page 100 Enter the value by mm using the keypad. Refer to the conversion rate be- low. 1 in. = 25.4 mm When im9220010 and 9263 are installed, adjustments can be made using both the “Punch Adjustment” and “Z-Fold Position Adjustment” param- eters. Contact your technical representative. im7520/im6020 12-51...
Page 101 Touch [7 Expert Adjustment]. The Expert Adjustment screen appears. Touch [5 Finisher Adjustment]. The Finisher Adjustment screen appears. Touch [3 Punch Adjustment]. The Punch Adjustment screen appears. Touch [2 Punch Horizontal Position]. The Punch Horizontal Position screen appears. 12-52 im7520/im6020...
Page 102 Check the punch positions in the sample copy. If the desire print results are not achieved, change the adjustment val- – If the punch positions are too far on the right side of the paper, touch [+] (between 0.1 mm and 5.0 mm). im7520/im6020 12-53...
Page 103 Enter the value by mm using the keypad. Refer to the conversion rate be- low. 1 in. = 25.4 mm When im9220010 and 9263 are installed, adjustments can be made using both the “Punch Adjustment” and “Z-Fold Position Adjustment” param- eters. Contact your technical representative. 12-54 im7520/im6020...
Page 104 Touch [7 Expert Adjustment]. The Expert Adjustment screen appears. Touch [5 Finisher Adjustment]. The Finisher Adjustment screen appears. Touch [3 Punch Adjustment]. The Punch Adjustment screen appears. Touch [3 Punch Unit Vert. Position]. The Punch Unit Vert. Position screen appears. im7520/im6020 12-55...
Page 105 Check the sample copy for the punch positions and for the center of the paper. If the desire print results are not achieved, change the adjustment val- – If the punch positions are too far above the center of the paper, touch [+] (between 0.1 mm and 5.0 mm). 12-56 im7520/im6020...
Page 106 Enter the value by mm using the keypad. Refer to the conversion rate be- low. 1 in. = 25.4 mm When im9220010 and 9263 are installed, adjustments can be made using both the “Punch Adjustment” and “Z-Fold Position Adjustment” param- eters. Contact your technical representative. im7520/im6020 12-57...
Page 107 Touch [7 Expert Adjustment]. The Expert Adjustment screen appears. Touch [5 Finisher Adjustment]. The Finisher Adjustment screen appears. Touch [3 Punch Adjustment]. The Punch Adjustment screen appears. Touch [4 Punch Unit Hor. Position]. The Punch Unit Hor. Position screen appears. 12-58 im7520/im6020...
Page 108 Check the punch positions in the sample copy. If the desire print results are not achieved, change the adjustment val- – If the punch positions are too far on the right side of the paper, touch [+] (between 0.1 mm and 5.0 mm). im7520/im6020 12-59...
Page 109 Enter the value by mm using the keypad. Refer to the conversion rate be- low. 1 in. = 25.4 mm When im9220010 and 9263 are installed, adjustments can be made using both the “Punch Adjustment” and “Z-Fold Position Adjustment” param- eters. Contact your technical representative. 12-60 im7520/im6020...
Page 110 Touch [7 Expert Adjustment]. The Expert Adjustment screen appears. Touch [5 Finisher Adjustment]. The Finisher Adjustment screen appears. Touch [3 Punch Adjustment]. The Punch Adjustment screen appears. Touch [5 Punch Resist Loop Size]. The Punch Regist Loop Size screen appears. im7520/im6020 12-61...
Page 111 If the positions of the punched holes are not aligned on the paper, touch [+] and [–] to increase or decrease the adjustment (between –16.0 mm and 16.0 mm). If the adjustment value is large, the edge of the paper may become folded. 12-62 im7520/im6020...
Page 112 Touch [1 System Setting]. The System Setting screen appears. Touch [7 Expert Adjustment]. The Expert Adjustment screen appears. Touch [5 Finisher Adjustment]. The Finisher Adjustment screen appears. Touch [4 Z-Fold Position Adjustment]. The Z-Fold Position Adjustment screen appears. im7520/im6020 12-63...
Page 113 Touch [Test Copy]. The Test Copy screen appears. Press the [Start] key. The sample copy is printed. Touch [Close]. The 1st Z-Folded Position or 2nd Z-Folded Position screen appears again. Check the folding positions in the sample copy. 12-64 im7520/im6020...
Page 114 [+] (between 0.1 mm and 12.7 mm). 1st Z-Folded Position 2nd Z-Folded Position – If the folding position is too far on the right side of the paper, touch [–] (between –0.1 mm and –12.8 mm). 1st Z-Folded Position 2nd Z-Folded Position im7520/im6020 12-65...
Page 115 Display the Administrator Setting screen. Touch [1 System Setting]. The System Setting screen appears. Touch [7 Expert Adjustment]. The Expert Adjustment screen appears. Touch [5 Finisher Adjustment]. The Finisher Adjustment screen appears. Touch [5 Tri-Fold Position]. The Tri-Fold Position screen appears. 12-66 im7520/im6020...
Page 116 Check the folding positions in the sample copy. If the desire print results are not achieved, change the adjustment val- – If the folding position is too far on the right side of the paper, touch [+] (between 0.1 mm and 12.7 mm). im7520/im6020 12-67...
Page 117 0 [6 2 Position Staple] appears only if finisher 9204 is installed. Display the Administrator Setting screen. Touch [1 System Setting]. The System Setting screen appears. Touch [7 Expert Adjustment]. The Expert Adjustment screen appears. Touch [5 Finisher Adjustment]. The Finisher Adjustment screen appears. 12-68 im7520/im6020...
Page 118 Repeat steps 6 through 11 until the desired print results are achieved. Touch [OK]. – To cancel changes to the settings, touch [Cancel]. Note Enter the value by mm using the keypad. Refer to the conversion rate be- low. 1 in. = 25.4 mm im7520/im6020 12-69...
Page 119: Cover Sheet Tray Size
Load A4 w -size paper into the selected paper tray. Press the [Start] key. – Adjust the cover sheet feeder tray. To adjust the other paper tray , repeat steps 6 through 8. Touch [Close]. – The Finisher Adjustment screen appears again. 12-70 im7520/im6020...
Page 120: Authentication Method
Limits on the number of pages printed – Management of personal boxes by each owner – Delete and restrict jobs of other users - Account track – Counters for printing/scanning from each account – Limits on the number of pages printed im7520/im6020 12-71...
Page 121 (each user) and on each depart- ment (each account). Note The account track and user authentication settings can be specified sep- arately. Check the differences between these features, and then specify the appropriate settings. 12-72 im7520/im6020...
Page 122 This setup is used when the machine is used by multiple employees with each employee performing multiple duties, which are to be totaled separate- ly. With this setup, totals can be maintained on each employee (each user) and on each duty of the employee (each account). im7520/im6020 12-73...
Page 123 To cancel user authentication, touch [OFF]. – To use the user authentication function from an external server, touch [ON (External Server)], and then select the server type. – To use the user authentication function of this machine, touch [ON (MFP)]. 12-74 im7520/im6020...
Page 124 MFP: This machine can be used only with user authentication. – To require all information to be entered for user authentication and account tracking each time that the machine is used, touch [Do Not Synchronize]. im7520/im6020 12-75...
Page 125 If no password is speci- fied, authentication will fail. Do not differentiate between uppercase and lowercase letters in the user name for the external server. Since the im7520/im6020 cannot differenti- ate between uppercase and lowercase letters, the operation may not be performed correctly.
Page 126 PageScope Data Administrator. For details, refer to the User’s Guide for PageScope Data Administrator. If user authentication is changed from external server authentication to machine authentication, the data is not cleared. To cancel changes to the settings, touch [Cancel]. im7520/im6020 12-77...
Page 127: Default Settings
Touch [2 User Authentication Setting]. The User Authentication Setting screen appears. Can [2 User Authentication Setting] be selected? % [2 User Authentication Setting] is not available if “User Authentica- tion” on the General Settings screen is set to “OFF”. 12-78 im7520/im6020...
Page 128 To permit the operation to be performed, touch [Allow]. – To prohibit the operation to be performed, touch [Restrict]. Touch [OK]. The default function permissions are set. Note To limit machine use by authorized users, specify settings in the User Registration screen. im7520/im6020 12-79...
Page 129 The User Authentication/Account Track screen appears. Touch [2 User Authentication Setting]. The User Authentication Setting screen appears. Touch [2 User Registration]. The User Registration screen appears. Touch the button for the desired user. The User Registration screen for the selected user appears. 12-80 im7520/im6020...
Page 130 Type in the password (up to 64 characters), and then touch [OK]. A screen for retyping the password appears. Retype the password specified in step 9, and then touch [OK]. The user password is set. Touch [E-Mail Address]. The E-Mail Address screen appears. im7520/im6020 12-81...
Page 131 At this time, do not turn off the machine with the main power switch. Touch [OK]. The maximum number of prints allowed are set. Touch [Function Permission]. The Function Permission screen appears. 12-82 im7520/im6020...
Page 132 The functions are selected in the following order: Copy → Scan → Box. – If no operation is permitted, user authentication cannot be per- formed. Touch [OK]. The function permissions are set. Touch [OK]. – To erase the current user, touch [Cancel]. im7520/im6020 12-83...
Page 133 To check the counter Display the Administrator Setting screen. – For details on displaying the Administrator Setting screen, refer to “Displaying the Administrator Setting Screen” on page 12-39. Touch [4 User Authentication/Account Track]. The User Authentication/Account Track screen appears. 12-84 im7520/im6020...
Page 134 User Counter screen for the current user. A confirmation mes- sage appears, asking whether the counter should be cleared. To clear the counters for the current user, touch [Yes]. The maximum number allowed is not cleared. Touch [Close]. im7520/im6020 12-85...
Page 135: Account Track Setting
For details on displaying the Administrator Setting screen, refer to “Displaying the Administrator Setting Screen” on page 12-39. Touch [4 User Authentication/Account Track]. The User Authentication/Account Track screen appears. Touch [3 Account Track Setting]. The Account Track Setting screen appears. Touch [1 Account Track Registration]. 12-86 im7520/im6020...
Page 136 Touch the button for the desired account. The Account Track Registration screen appears. If “Account Name & Password” was selected: If “Password Only” was selected: How is the selected account information deleted? % Touch [Delete]. Touch [Account Name]. The Account Name screen appears. im7520/im6020 12-87...
Page 137 A password that repeats the same character (for example, “11111111”) A password containing less than 8 characters A screen for retyping the password appears. Retype the password specified in step 9, and then touch [OK]. The account password is set. 12-88 im7520/im6020...
Page 138 At this time, do not turn off the machine with the main power switch. Touch [OK]. The maximum number of prints allowed is set. Touch [OK]. – To cancel changes to the settings, touch [Cancel]. im7520/im6020 12-89...
Page 139 - Large Size: Shows the total number of printouts made on large-sized pa- Scan - Total: Shows the total number of pages scanned/the total number of pag- es printed - Large Size: Shows the total number of large-sized pages scanned/the to- tal number of pages printed 12-90 im7520/im6020...
Page 140 Account Track Counter screen for the current account. A confirmation message appears, asking whether the counter should be cleared. To clear the counters for the current account, touch [Yes]. The maximum number allowed is not cleared. Touch [Close]. im7520/im6020 12-91...
Page 141: Password Rules
Limitations on the number of Limitations on registering/changing characters 8 alphanumeric characters (case- • A password that consists of a repetition of the same sensitive) character cannot be registered. • The same password as one before being changed can- not be registered. 12-92 im7520/im6020...
Page 142 Use the user password/account password when user authentication/ac- count track settings have been applied. For details on the “User Box Password”, “ID for the confidential docu- ment” and “Password for the confidential document”, refer to the im7520/im6020 User’s Guide [Box Operations]. im7520/im6020 12-93...
Page 144 Appendix...
Page 145: Entering Text
The keypad can also be used to type in numbers. Any of the following keyboards may appear. Example Password input screen: Screen for entering the name of a custom paper size: 13-2 im7520/im6020...
Page 146 Appendix Touching [Shift] switches the keyboard display between lowercase letters (numbers) and uppercase letters (symbols). im7520/im6020 13-3...
Page 147: Available Characters
To change a character in the entered text, touch [←] and [→] to move the cursor to the character to be changed, touch [Delete], and then type in the desired letter or number. List of Available Characters Alphanumeric characters / (Space) symbols 13-4 im7520/im6020...
Page 148: Function Combination Table
Appendix 13.2 Function Combination Table Function Combination Table im7520/im6020 13-5...
Page 149 Appendix 13-6 im7520/im6020...
Page 150 Appendix im7520/im6020 13-7...
Page 151 Appendix 13-8 im7520/im6020...
Page 152 Appendix im7520/im6020 13-9...
Page 153 Appendix 13-10 im7520/im6020...
Page 154 If the cover sheet is thick paper and the paper for the body text is plain paper while using the “Cover Mode” function, a Staple setting can also be selected. In any other case, the settings cannot be combined, the setting specified first is given priority, and a warning message appears. im7520/im6020 13-11...
Page 155 A setting under “Back Cover” cannot be combined with the “Booklet” function or “Half Fold” or “Fold & Staple” settings. The “Booklet” function or “Half Fold” or “Fold & Staple” settings are given priority. (If the “Booklet” function or “Half Fold” or “Fold & Staple” settings were specified first, a warning message appears.) 13-12 im7520/im6020...
Page 156 Index...
Page 157: Table Of Contents
Automatic tray switching ....7-7 Cover mode ........8-12 Available characters ...... 13-4 Cover pages ......8-12 8-16 Cover sheet feeder control panel Basic screen ........2-17 ............2-11 Cover sheet feeder PI-501 BM tray (Finisher) ......2-9 ........2-7 2-11 14-2 im7520/im6020...
Page 158 Job history ........11-12 Job list ........... 11-2 Fax key .......... 2-14 Job settings ........11-8 Features ......... x-15 Feeding documents ......3-7 Finisher adjustment ..... 12-45 Key counter ........2-7 Finisher FS-504 ....2-7 Key repeat start/interval time ..4-23 im7520/im6020 14-3...
Page 159 Power plug ........1-5 Mode memory key ......2-15 Power save key ......2-14 Multi-page document scanning ..3-13 Power source ......... 1-16 Preset zoom ratios ......3-32 Preventive maintenance time ..10-7 Negative/positive reverse ....8-28 Printer adjustment ....... 12-41 14-4 im7520/im6020...
Page 160 Set numbering ....... 8-88 Touch panel adjustment ....4-35 Set range ........8-43 Tray 1 ........2-3 2-39 Set zoom ratios ......3-37 Tray 2 ........2-3 2-39 Shift tray SF-601 .... 2-7 2-13 Tray 3 ........2-3 2-41 im7520/im6020 14-5...
Page 161 Utility/Counter key ......2-15 Watermark ........8-92 Weekly timer ........2-31 Working table ........2-3 Z-fold position adjustment ..12-63 Z-folding unit ZU-602 ..2-7 2-12 Zoom minimal setting ....3-31 Zoom ratio setting ....3-33 3-38 Zoom settings ........ 3-29 14-6 im7520/im6020...
Page 162 Trumbull, CT 06611 ® Imagistics International Ltd. Field House, Station Approach Harlow, Essex CM20 2TX ©Imagistics International Inc. 2005 Printed in China The information contained in this manual is subject to change without notice to incorporate improvements made to the products listed in this manual.
Page 163 Additional Copy Operations...
Page 164: Copy Settings
Additional Copy Operations Additional Copy Operations Checking the Copy Settings (Mode Check) From the Mode Check screens, the current copy settings can be checked and changed if desired. To check the settings Press the [Mode Check] key. Mode Check im7520/im6020...
Page 165 Additional Copy Operations The Mode Check screen appears. im7520/im6020...
Page 166 Touch [←Back] or [Fwd.→] until the button for the function to be changed is displayed. Touch the button for the setting that you wish to change. The screen for specifying the setting appears. Follow the appropriate procedure to change the setting. im7520/im6020...
Page 167: Proof Copy
Touch [Change Setting] in the screen that appeared when the sample copy is printed. – Before printing a large number of copies, a single proof copy can first be printed so that it can be checked. This prevents copy errors from occurring. im7520/im6020...
Page 168 Why is the button for the setting that I wish to change not dis- played? The copy setting cannot be changed. % If the copy settings cannot be changed, stop printing the proof copy. Then, press the [Reset] key to cancel the copy settings, and then specify the desired settings. im7520/im6020...
Page 169 To stop the proof copy while scanning or printing, perform the op- eration described in “Stopping Scanning/Printing” on page 3-74. – If multiple copies have been specified, another sample copy can be printed. Touch [Print]. – The remaining copies begin to be printed. im7520/im6020...
Page 170: Interrupting A Copy Job
Why is the [Interrupt] key not available? % The [Interrupt] key cannot be pressed while an original is being scanned. Select the desired copy settings. Press the [Start] key. Printing begins for the job that was interrupted. im7520/im6020...
Page 171 The indicator on the [Interrupt] key goes off, and Interrupt mode is can- celed. The settings return to those specified before printing was interrupted. Note If the interrupting job is cancelled, printing for the interrupted job auto- matically restarts. im7520/im6020...
Page 172 The Program Name screen appears. Why is [Program Registration] not available? % If 30 copy programs have been registered, delete an unnecessary copy program. For details on deleting copy programs, refer to “To delete a copy program” on page 4-13. 4-10 im7520/im6020...
Page 173 How is a job deleted? % Touch the button for the desired copy program, and then touch [Del.]. In the screen that appears, requesting confirmation to delete the copy program, touch [Yes] to delete the selected copy program. im7520/im6020 4-11...
Page 174 For details, refer to “System Setting” on page 12-26. To stop registering the program, press the [Reset] key or the [Mode Mem- ory] key. No matter which screen is displayed, the registration is cancelled. Otherwise, continue to touch [Cancel] until the Basic screen is displayed. 4-12 im7520/im6020...
Page 175 In the Recall Copy Program screen, touch the button for the copy pro- gram to be deleted. Touch [Del.]. A message appears, requesting confirmation to delete the copy pro- gram. Touch [Yes]. The Recall Copy Program screen appears again. The copy settings registered in the copy program are erased. im7520/im6020 4-13...
Page 176 The Recall Copy Pro- gram screen appears. Touch the button for the copy program registered with the desired copy settings. – If the copy settings in the selected copy program are not to be checked, skip to step 8. 4-14 im7520/im6020...
Page 177 If [OK] is touched with no copy program selected, the Basic screen appears again without a copy program recalled. The selected copy program is recalled and the Basic screen appears again. Press the [Start] key. Copying begins with the recalled copy settings. im7520/im6020 4-15...
Page 178 Additional Copy Operations Note To stop recalling the copy program, press the [Reset] key or the [Mode Memory] key, or touch [Cancel]. The copy settings cannot be changed from the Mode Check screens. 4-16 im7520/im6020...
Page 179 Touch [Exit] to quit the Help mode and return to the screen that was dis- played before the [Help] key was pressed. The [Fax] key is currently not available. im7520/im6020 4-17...
Page 180 The items displayed in the Help menu for the [Name and function of each part] differ depending on the options that are installed. To display the next screen higher in the menu structure, touch [ Help screens (3rd level) (Example: [Copy], then [Basic]) 4-18 im7520/im6020...
Page 181 Press the key in the keypad for the number of the desired item in the Function Map screen. To return to the Help Menu screen, touch [ ] in the Help screen dis- played by selecting an item in a Function Map screen. im7520/im6020 4-19...
Page 182 [Start], [Stop], [C] (clear), [Interrupt], [Proof Copy], [Access], [Mode Mem- ory], [Enlarge Display], [Mode Check] With the Basic screen displayed, press the [Help] key. Help The Main Help Menu screen appears. Touch [Copy] or press the [1] key in the keypad. 4-20 im7520/im6020...
Page 183 Touch the button for the desired information or press the key in the keypad for the number to the left of the desired information to display the corresponding Help screen. After checking the Help information, touch [Exit] or press the [Help] key. The Basic screen appears again. im7520/im6020 4-21...
Page 184 To return to the upper level Help Menu screen, touch [ ] in the Help screen displayed by selecting an item in a Function Map. The screen that was displayed before the [Help] key was pressed ap- pears again. 4-22 im7520/im6020...
Page 185: Accessibility Mode
The factory default setting for “Time To Start” is 0.8 second and the setting for “Interval” is 0.3 second. 0 The settings specified for the “Key Repeat Start/Interval Time” function are only applied in the Enlarge Display mode. Display the Accessibility Setting screen. (To display the screen, refer to page 4-23) im7520/im6020 4-23...
Page 186 – To extend the time, touch [+].To reduce the time, touch [–]. – Both settings can be set between 0.1 and 3.0 seconds in 0.1-sec- ond intervals. – To cancel changes to the settings, touch [Cancel]. 4-24 im7520/im6020...
Page 187 For details on the Enlarge Display mode, refer to the Enlarge Display Operations of the User’s Guide. Detail To return to the Basic screen from the Accessibility Setting screen, press the [Accessibility] key or the [Reset] key. im7520/im6020 4-25...
Page 188: Enlarge Display Timer Setting
0 The “Enlarge Display Timer Setting” function is available only in Enlarge Display mode. Display the Accessibility Setting screen. (To display the screen, refer to page 4-23) Touch [Enlarge Display Timer Setting] or press the [2] key in the key- pad. 4-26 im7520/im6020...
Page 189 With the Enlarge Display mode in Copy mode, the function and setting names and the illustrations are displayed at a larger size so that they can be seen more easily. For details on the Enlarge Display mode, refer to the [Enlarge Display Operations] of the User’s Guide. im7520/im6020 4-27...
Page 190: Message Display Time
The factory default setting is “3 sec.”. Display the Accessibility Setting screen. (To display the screen, refer to page 4-23) Touch [Message Display Time] or press the [3] key in the keypad. The Message Display Time screen appears. 4-28 im7520/im6020...
Page 191 Select whether messages are displayed for 3 seconds or for 5 sec- onds. – To cancel changes to the settings, touch [Cancel]. Touch [OK]. The Accessibility Setting screen appears again. Touch [Close] or press the [Accessibility] key. The Basic screen appears again. im7520/im6020 4-29...
Page 192 The factory default setting for “Accept Sound Setting” is “ON”. Display the Accessibility Setting screen. (To display the screen, refer to page 4-23) Touch [Sound Setting] or press the [4] key in the keypad. The Sound Setting screen appears. 4-30 im7520/im6020...
Page 193 Select the desired setting for “Accept Sound Setting”. – To produce a sound, touch [ON]. To not produce a sound, touch [OFF]. – To cancel changes to the settings, touch [Cancel]. Touch [OK]. The Sound Setting screen appears again. im7520/im6020 4-31...
Page 194 Additional Copy Operations Touch [OK]. The Accessibility Setting screen appears again. Touch [Close] or press the [Accessibility] key. The Basic screen appears again. 4-32 im7520/im6020...
Page 195 Display the Accessibility Setting screen. (To display the screen, refer to page 4-23) Touch [Sound Setting] or press the [4] key in the keypad. The Sound Setting screen appears. Touch [Touch Panel Volume Adjust] or press the [2] key in the keypad. im7520/im6020 4-33...
Page 196 The volume can be set in 16 levels (between 0 and 16). – To cancel changes to the settings, touch [Cancel]. Touch [OK]. The Sound Setting screen appears again. Touch [OK]. The Accessibility Setting screen appears again. Touch [Close] or press the [Accessibility] key. The Basic screen appears again. 4-34 im7520/im6020...
Page 197: Touch Panel Adjustment
The Touch Panel Adjust- ment screen appears. Why does the ma- chine not respond when [Touch Panel Adj.] is touched? The touch sensors are not aligned on the touch panel. % Press the [5] key in the keypad. im7520/im6020 4-35...
Page 198 Touch [Close] or press the [Accessibility] key. The Basic screen appears again. Note If the touch panel cannot be adjusted, contact the technical representa- tive. Detail To cancel the touch panel adjustment, press the [Stop] key or the [Reset] key. 4-36 im7520/im6020...
Page 199 Troubleshooting...
Page 200: Malfunction Detected
(call technical representative screen) The phone number and fax number for the usual technical representative ap- pears in the center of the call technical representative screen. Display in Enlarge Display Mode If a malfunction occurs, the screen shown below appears. im7520/im6020...
Page 201 To call the technical representative Write down the malfunction code (for example, C-0001) in the call tech- nical representative screen. Turn off the sub power switch. Use the main power switch to turn off the ma- chine. im7520/im6020...
Page 202 Center is automatically notified of the malfunction code. After the message “Malfunction was detected. CS Remote Care has called the Service Center.” appears, turn off the sub power switch and the main power switch, and then unplug the machine from the electrical outlet. im7520/im6020...
Page 203: Misfeed
The illustration above shows all “o” and arrows displayed; however, nor- mally, all marks will not appear. Error codes may appear in the illustration description area of the JAM lo- cation display screen. For details, contact your technical representative. im7520/im6020...
Page 204: Jam Location Display Screen
Clear the paper misfeed according to the instructions that appear in the screen. – When removing misfeed paper, be careful that the paper does not tear and remain in the machine. – Do not touch or scratch the surface of the drum. im7520/im6020...
Page 205 Parts in the fusing unit on the left side inside the machine are extremely hot. In order to reduce the risk of burns, do not touch any part in this unit when clearing paper misfeeds. im7520/im6020...
Page 206: Replenish Paper
Into the Tray 1 or 2” on page 2-39, “Loading Paper Into the Tray 3 or 4” on page 2-41, “Loading Paper Into the Bypass Tray” on page 2-44, and “Loading Paper Into the LCT (9208/9209)” on page 2-48. im7520/im6020...
Page 207 This message appears when the memory becomes full and scanning stops while scanning in Copy mode. To print all pages that have been scanned, touch [Print]. To delete the job for the scanned pages, touch [Delete]. Display in Enlarge Display Mode im7520/im6020...
Page 208 Check the number of pages counted for the document, and then adjust the number of pages in the job to be queued. Display in Enlarge Display Mode 5-10 im7520/im6020...
Page 209: Simple Troubleshooting
(See p. 2-39, p. 2-41, p. 2-44 and p. 2-48.) Was the document not Position the document so that it is pressed close enough pressed closely against the original against the original glass? glass. (See p. 3-9.) im7520/im6020 5-11...
Page 210 The printed page is Was paper that curls easily Remove the paper from the paper curled. (as with recycled paper) tray, turn it over, and then load it used? again. Replace the paper with paper that is not damp. 5-12 im7520/im6020...
Page 211 Securely close the ADF. Is the document one that Replace the document with one that does not meet the specifica- meets the specifications. (See tions? p. 7-33.) Is the document correctly Position the document correctly. loaded? (See p. 3-7.) im7520/im6020 5-13...
Page 212 (when im9220010/9263 is installed on 9202/ 9204) If any message other than those listed above appears, perform the operation described in the message. If the problem is not corrected after the described operation is performed, contact your technical representative. 5-14 im7520/im6020...
Page 213: Messages
Since the toner has run out, Replace the toner cartridge. tridge. the machine is unable to make copies. Stapler empty. Replace The staples have run out. Replace the staple cartridge. (See Staple Cartridge or can- p. 9-7.) cel Staple mode. im7520/im6020 5-15...
Page 214 Representative. panel. If any message other than those listed above appears, perform the operation described in the message. If the problem is not corrected after the described operation is performed, contact your technical representative. 5-16 im7520/im6020...
Page 215 Specifications...
Page 216: Specifications
Tray 2: Normal paper: 1,000 sheets (20lb) Tray 3 and 4 (universal tray) Normal paper: 500 sheets (20lb) Bypass tray (universal tray): Normal paper: 100 sheets (20lb) Warm-up time im7520: About 5 minutes im6020: About 4 minutes and 30 seconds im7520/im6020...
Page 217 Leading edge/trailing edge: Less than 1/16 in. ± 1/16 in. (front side), 1/16 in. ± 1/16 in. (back side); Front edge/rear edge: Less than 1/16 in. ± 1/16 in. First copy im7520: 3.0 seconds or less im6020: 3.5 seconds or less Copy speed im7520: 75 ppm (8.5 ×...
Page 218 — — 8-1/2 × 11 v — — — — 8-1/2 × 14 w — 8-1/2 × 11 w — 5-1/2 × 8-1/2 v — 5-1/2 × 8-1/2 w — — — — — o: Possible —: Not possible im7520/im6020...
Page 219 92-1/2 lb There are four F4 (Foolscap) sizes: 8-1/4 × 13 w, 8-1/8 × 13-1/4 w, 8- 1/2 × 13 w and 8 × 13 w. Any one of these sizes can be selected. For details, contact your technical representative. im7520/im6020...
Page 220 Supplied from main body Dimensions 16-3/4 in. (W) × 25-3/4 in. (D) × 39 in. (H) Weight Approx.132-1/4 lb Consumables Staple cartridge Finisher 9204 Specifications Exit trays Main tray, sub tray, BM tray Settings Non-stapled, Offset, Staple, Booklet, Tri-Fold im7520/im6020...
Page 221 Normal paper (16 to 24 lb), Thick paper (24-1/4 to 34 lb) Paper sizes 2 holes: 11 × 17w to 5-1/2 × 8-1/2 w/v, 8-1/2 × 14 w and F4 3 holes: 11 × 17w and 8-1/2 × 11 w Power requirements Supplied from finisher im7520/im6020...
Page 222: Cover Sheet Feeder
20 in. (W) × 24-1/2 in. (D) × 8-3/4 in. (H) Weight Approx. 23-1/4 lb Shift Tray 9207 Specifications Paper types Normal paper (16 to 24 lb), thick paper (24-1/4 to 53-1/4 lb), thin paper (13-1/4 to 15-3/4 lb) Paper sizes 11× 17 w to 5-1/2 × 8-1/2 w/v im7520/im6020...
Page 223: Accessories
Power requirements Supplied from main body Power requirements 15-3/4 in. (W) × 23-1/2 in. (D) × 19 in. (H) Weight Approx. 33 lb Accessories Specifications im7520/im6020 CD-ROM Drum Developer Paper tray labels User’s Guides 1 each User’s Guide [Copy Opera- tions] User’s Guide [Enlarge Display...
Page 225 Copy Paper/Original...
Page 226: Copy Paper
5-1/2 × 8-1/2w/v, 8-1/2 × 14w and F4 Staple: 11 × 17w to 5-1/2 × 8-1/2w Punch:11 × 17w to 5-1/2 × 8-1/2w/v and 8-1/2 × 14w* Sub tray: “Sort” and “Group” settings: 11 × 17w to 5-1/2 × 8-1/2 w/v, 8-1/2 × 14w and F4 im7520/im6020...
Page 227: Paper Capacities
Tray 2 1,000 sheets — — (20 lb paper) Tray 3 and 4 500 sheets — — (20 lb paper) 9208 4,000 sheets — — (20 lb paper) 9209 4,000 sheets — — (20 lb paper) Double-sided copies — — im7520/im6020...
Page 228: Special Paper
Tab Paper Select this setting when tab paper is loaded. A paper tray with this setting is not automatically se- lected when the “Auto Paper Select” setting is spec- ified or when the paper trays are switched automatically. im7520/im6020...
Page 229 Trace Select this setting when trace paper is loaded. A paper tray with this setting is not automatically se- lected when the “Auto Paper Select” setting is spec- ified or when the paper trays are switched automatically. im7520/im6020...
Page 230: Paper Storage
Paper that has not been loaded should be kept wrapped or placed in a plastic bag and stored in a cool, dark location with little humidity. - Store the paper laying flat, not standing on its edge. Curled paper may cause paper misfeeds. - Keep paper out of the reach of children. im7520/im6020...
Page 231: Automatic Tray Switching
When a different paper tray is automatically selected, the next paper tray is chosen from the priority list specified using the “Auto Tray Select Setting” parameter of Utility mode. Detail To change the order in which the paper trays are selected, refer to “Sys- tem Setting” on page 12-14. im7520/im6020...
Page 232: Specifying The Paper Setting For The Bypass Tray
The size of the paper loaded into the bypass tray can be detected automat- ically. In the Basic screen, touch [Paper]. The Paper screen appears. Touch the button for the bypass tray, and then touch [Change Tray Set- tings]. im7520/im6020...
Page 233 Copy Paper/Original Touch [Auto Detect]. Touch [OK] twice. The Basic screen appears again. Note The factory default setting is “Auto Detect”. im7520/im6020...
Page 234: Standard Size Settings
The following procedure describes how to specify the setting for A4w paper loaded into the bypass tray. In the Basic screen, touch [Paper]. The Paper screen appears. Touch the button for the bypass tray, and then touch [Change Tray Set- tings]. 7-10 im7520/im6020...
Page 235 The Standard Size screen appears. Touch [A4w]. Touch [OK] three times. The Basic screen appears again. Reminder If paper other than the specified paper size is loaded, a paper misfeed may occur since the paper size is not automatically detected. im7520/im6020 7-11...
Page 236 In the Basic screen, touch [Paper]. The Paper screen appears. Touch the button for the bypass tray, and then touch [Change Tray Set- tings]. Touch [Custom Size]. The Custom Size screen appears. 7-12 im7520/im6020...
Page 237 % The names of the stored paper sizes “memory1” and “memory2” can be changed. For details on changing the names, refer to “To store a non-standard paper size (Custom Size settings Store)” on page 7-14. Touch [OK] three times. The Basic screen appears again. im7520/im6020 7-13...
Page 238: Custom Size Settings Store
Storing paper sizes that are used often allows the paper size to be quickly selected, without having to re-enter the setting. In the Basic screen, touch [Paper]. The Paper screen appears. Touch the button for the bypass tray, and then touch [Change Tray Set- tings]. Touch [Custom Size]. 7-14 im7520/im6020...
Page 239 % Touch [Custom Name], then type the new name into the Custom Name screen that appeared, and then touch [OK]. % Use the keyboard that appeared in the screen to type in the new name, and then touch [OK]. im7520/im6020 7-15...
Page 240: Entering Text
Copy Paper/Original % For details on typing in text, refer to “Entering Text” on page 13-2. Touch [OK] four times. The Basic screen appears again. 7-16 im7520/im6020...
Page 241 11 × 17-size original to be print- In the Basic screen, touch [Paper]. The Paper screen appears. Touch the button for the bypass tray, and then touch [Change Tray Set- tings]. im7520/im6020 7-17...
Page 242 Select the size of the paper to be loaded and image adjustment. – To select a paper size in centimeters, touch [Metric]. The list of pa- per sizes in centimeters appears. To change the size, touch [Change Size]. The Change Size screen for oversized paper appears. 7-18 im7520/im6020...
Page 243 The Basic screen appears again. Note The selected size button is programmed with the entered paper size, so that the paper size is available to be selected again without having to be typed in. In addition, the size can be changed. im7520/im6020 7-19...
Page 244 “Auto Paper Select” setting or the automatic tray switching feature. In the Basic screen, touch [Paper]. The Paper screen appears. Touch the button for the bypass tray, and then touch [Change Tray Set- tings]. 7-20 im7520/im6020...
Page 245 Touch [OK] twice. The Basic screen appears again. Reminder If overhead projector transparencies or thick paper is loaded into the by- pass tray, be sure to select the corresponding paper type, otherwise a paper misfeed may occur. im7520/im6020 7-21...
Page 246: Specifying Paper Settings For Paper Trays
– An item can also be selected by pressing the key in the keypad for the number beside the desired button. – For “2 User Setting”, press the [2] key in the keypad. The User Setting screen appears. 7-22 im7520/im6020...
Page 247 The System Setting screen appears. Touch [3 Paper Tray Setting]. The Paper Tray Setting screen appears. Note To change the paper size for paper loaded into the tray 1 and 2 and the LCT (9208/9209), contact your technical representative. im7520/im6020 7-23...
Page 248: Standard Size 1 Settings
For details on changing the paper size for the tray 3 and 4, refer to “Loading Paper of a Different Size Into Paper Trays” on page 2-51. The Paper Type screen appears. Touch the button for the tray 3, and then touch [Paper Size]. The Paper Size screen appears. 7-24 im7520/im6020...
Page 249: Standard Size 2 Settings
Paper Tray Setting screen” on page 7-22. – For details on changing the paper size for the tray 3 and 4, refer to “Loading Paper of a Different Size Into Paper Trays” on page 2-51. The Paper Type screen appears. im7520/im6020 7-25...
Page 250 Touch [Standard Size2]. – The Paper Size screen that appears differs depending on the paper size type that is selected. Buttons for the available paper sizes appear. Select the size of the paper to be loaded. Touch [OK]. 7-26 im7520/im6020...
Page 251 For details on changing the paper size for the tray 3 and 4, refer to “Loading Paper of a Different Size Into Paper Trays” on page 2-51. The Paper Type screen appears. Touch the button for the tray 3, and then touch [Paper Size]. The Paper Size screen appears. im7520/im6020 7-27...
Page 252 “Input Error” appears. Type a value within the allowable range. If the value was incorrectly entered, press the [C] (clear) key to erase the value, and then spec- ify the correct value. Touch [OK]. 7-28 im7520/im6020...
Page 253 For details on changing the paper size for the tray 3 and 4, refer to “Loading Paper of a Different Size Into Paper Trays” on page 2-51. The Paper Type screen appears. Touch the button for the tray 3, and then touch [Paper Size]. The Paper Size screen appears. im7520/im6020 7-29...
Page 254 “Input Error” appears. Type a value within the allowable range. If the value was incorrectly entered, press the [C] (clear) key to erase the value, and then spec- ify the correct value. Select the desired image position. Touch [OK]. 7-30 im7520/im6020...
Page 255 For details on displaying the Paper Tray Setting screen, refer to “To display the Paper Tray Setting screen” on page 7-22. The Paper Type screen appears. Touch the button for the tray 1, and then touch [Paper Type]. The Paper Type screen appears. im7520/im6020 7-31...
Page 256 Copy Paper/Original Select the type of paper to be loaded. Touch [OK]. 7-32 im7520/im6020...
Page 257: Originals
100 sheets (21-1/4 lb paper) For documents of mixed sizes Single-Sided Original Double-Sided Original Original paper type/ 13-1/4 lb to 53-1/4 lb Weight Original size Refer to “Mixed originals paper sizes”. Paper capacity 100 sheets (21-1/4 lb paper) im7520/im6020 7-33...
Page 258 4 lb, thin paper: 13-1/4 lb to 15-3/4 lb Original size 11 × 17, 8-1/2 × 14, 8-1/2 × 11w/v, 5-1/2 × 8-1/2w/v, A3, B4, A4, B5w/v, B6w Paper capacity 100 sheets (21-1/4 lb paper) Note Z-folded original can only be scanned using the ADF. 7-34 im7520/im6020...
Page 259 To copy original that cannot be positioned into the ADF, position them on the original glass. Original Glass Original Original type Sheets, books (spreads), three-dimensional objects Original size 11 × 17 w to 5-1/2 × 8-1/2 w/v A3 w to B6 w Maximum weight 15 lb im7520/im6020 7-35...
Page 260 - Do not place objects exceeding 15 lb on the original glass, otherwise the original glass may be damaged. - If a book is placed on the original glass, do not press it down extremely hard, otherwise the original glass may be damaged. 7-36 im7520/im6020...
Page 261 Application Functions...
Page 262: Application
E F G H E F G H E F G H Detail For details on loading overhead projector transparencies, refer to “Paper Types and Paper Capacities” on page 7-3, “Loading Paper Into the Bypass Tray” on page 2-44. im7520/im6020...
Page 263 Paper Into the Bypass Tray” on page 2-44. Select “OHP” for the paper in the bypass tray. Touch [Paper] in the Basic screen, touch the button for the bypass tray, touch [Change Tray Settings], and then touch [OHP]. Touch [OK]. The Paper screen appears. im7520/im6020...
Page 264 Tray 3 or 4” on page 2-41, and “Loading Paper Into the Bypass Tray” on page 2-44. Touch [Application]. The Application screen appears. Touch [Sheet/Cover/Chapter Insert]. – To cancel all settings for the Application functions, touch [Reset]. The Sheet/Cover/Chapter Insert screen appears. im7520/im6020...
Page 265 Select the paper tray loaded with the interleaf paper. – To cancel changes to the settings, touch [Cancel]. – To cancel the “OHP Interleave” function, touch [OFF]. Touch [OK] twice. If necessary, specify any other copy settings. Press the [Start] key. im7520/im6020...
Page 266: Insert Image
When specifying a page in a double-sided original, the front and back sides of one page are considered as two pages. Therefore, to specify the back side of the second page of the original, specify “4”. Insert original (one-sided) Insert original Insert images Insert original (double-sided) im7520/im6020...
Page 267 To cancel all settings for the Application functions, touch [Reset]. Reminder Position the original in order, starting with the first page. The copy will not be printed as desired if the original is position starting with the last page. im7520/im6020...
Page 268 Load the main original (the one that the other original will be inserted into) into the ADF. Touch [Application]. The Application screen appears. Touch [Sheet/Cover/Chapter Insert]. The Sheet/Cover/Chapter Insert screen appears. Touch [Insert Image]. The Insert Image screen (for specifying settings) appears. im7520/im6020...
Page 269 Touch [Select] to enter the specified pages and display the Insert Image screen (with the list of specified pages). What will happen if there are more insertion pages than the number of pages that are specified? % The remaining insertion pages are added at the end of the original. im7520/im6020...
Page 270 Press the [Start] key. Scanning of the original to be inserted begins. What should be done if there are multiple original to be inserted? % Repeat steps 11 and 12 until all original to be inserted are scanned. 8-10 im7520/im6020...
Page 271 Application Functions Touch [Finish]. Press the [Start] key. Printing begins. im7520/im6020 8-11...
Page 272: Cover Mode
Back (Blank) Paper for the back cover sheet is added after the last page of the copy. The same operation is performed with double-sided copying. REPORT REPORT Front copy,Back copy REPORT REPORT Front blank,Back blank 8-12 im7520/im6020...
Page 273 Use paper with the same size for the cover pages and for the main body of the original, and load them in the same orientation. Touch [Application]. The Application screen appears. Touch [Sheet/Cover/Chapter Insert]. – To cancel all settings for the Application functions, touch [Reset]. The Sheet/Cover/Chapter Insert screen appears. im7520/im6020 8-13...
Page 274 To cancel the “Cover Mode” function, touch [OFF]. Select the paper tray loaded with the paper for the cover pages. – Depending on the desired setting, touch [Front Cover Paper] or [Back Cover Paper]. The corresponding Cover Paper screen appears. 8-14 im7520/im6020...
Page 275 Instead, only blank pages will be in- serted. Touch [OK] three times. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. im7520/im6020 8-15...
Page 276: Insert Sheet
A blank page is inserted as the 12th page of the copy. “2 > 1” The front side of the 11th page of the original is copied as the 6th page of the copy and a blank page is inserted as the 7th page of the copy. 8-16 im7520/im6020...
Page 277 Separate Batches (“Separate Scan” Setting)” on page 3-11. To cancel all settings for the Application functions, touch [Reset]. Optional paper trays (F1 and F2) appear when optional cover sheet feed- er 9262 is installed; however, they cannot be set. im7520/im6020 8-17...
Page 278 Use paper with the same size for the cover pages and for the main body of the original, and load them in the same orientation. Touch [Application]. The Application screen appears. Touch [Sheet/Cover/Chapter Insert]. The Sheet/Cover/Chapter Insert screen appears. 8-18 im7520/im6020...
Page 279 To cancel the “Insert Sheet” function, Touch [OFF]. The Insert Paper screen appears. Touch the button for the paper tray loaded with the paper for the inser- tion. Touch [OK]. The Insert Sheet screen (for specifying settings) appears. im7520/im6020 8-19...
Page 280 If “Blank” was selected in step 9, paper from the paper tray speci- fied in step 7 is inserted after the specified page. – Touch [Select] to enter the specified pages and display the Insert Sheet screen (with the list of specified pages). 8-20 im7520/im6020...
Page 281 [C] (clear) key in the keypad to remove the page number. Touch [OK] twice. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. im7520/im6020 8-21...
Page 282: Chapters
When copying double-sided documents while using the “Chapters” function, each side of one page of the document is considered two separate pages. In addition, paper tray loaded with paper for specific pages can be specified. Single-sided original Final copy Double-sided original 8-22 im7520/im6020...
Page 283 For details on positioning the original, refer to “Positioning the Original” on page 3-7. For an original that exceeds 100 pages, refer to “Scanning the Original in Separate Batches (“Separate Scan” Setting)” on page 3-11. To cancel all settings for the Application functions, touch [Reset]. im7520/im6020 8-23...
Page 284 Application Functions To copy using the “Chapters” function Position the original to be copied. Touch [Application]. The Application screen appears. Touch [Sheet/Cover/Chapter Insert]. The Sheet/Cover/Chapter Insert screen appears. Touch [Chapters]. The Chapters screen (for specifying settings) appears. 8-24 im7520/im6020...
Page 285 To cancel changes to the copy settings,Touch [Cancel]. – To cancel the “Chapter” function, Touch [OFF]. Touch [Chapter Paper]. The Chapter Paper screen appears. Touch the button for the paper tray loaded with the paper for the chap- ter title pages. im7520/im6020 8-25...
Page 286 Touch [Select] to enter the specified pages and display the Chapter screen (with the list of specified pages). What will happen if the specified page number is greater than the number of pages in the original? % That page number is ignored. 8-26 im7520/im6020...
Page 287 [C] (clear) key in the keypad to remove the page number. Touch [OK], and then touch [OK] in the next screen that appears. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. im7520/im6020 8-27...
Page 288 For details on positioning the original, refer to “Positioning the Orig- inal” on page 3-7. For an original that exceeds 100 pages, refer and “Scanning the Origi- nal in Separate Batches (“Separate Scan” Setting)” on page 3-11. Touch [Application]. The Application screen appears. 8-28 im7520/im6020...
Page 289 To cancel the “Neg-/Pos. Reverse” function, Touch [Neg-/Pos. Re- verse] again to deselect it. – To cancel all settings for the Application functions, touch [Reset]. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. im7520/im6020 8-29...
Page 290: Book Copy
Front and Back Cover The front cover, separate copies of each page in the page spreads and the back cover are printed in the original page order. When “Separation” is selected 1>1 1>2 8-30 im7520/im6020...
Page 291: Application Functions
Application Functions When “Front Cover” is selected SURVEYOR’S REPORT SURVEYOR’S REPORT SURVEYOR’S REPORT When “Front and Back Cover” is selected SURVEYOR’S REPORT SURVEYOR’S REPORT SURVEYOR’S REPORT SURVEYOR’S REPORT im7520/im6020 8-31...
Page 292 What should be done if the front and back covers are also being copied? % Scan the front cover, then the back cover, and then scan the re- mainder of the original. Load the paper to be used into the desired paper tray. Touch [Application]. The Application screen appears. 8-32 im7520/im6020...
Page 293 The Book Scanning screen appears. Touch the button for the desired setting. – If necessary, touch [Erase] or [Center Erase] under “Book Erase”. – To cancel changes to the settings, touch [Cancel]. – To cancel the “Book Copy” function, touch [OFF]. im7520/im6020 8-33...
Page 294 What do the Book Erase functions do? % “Erase” and “Center Erase” can be used together. How are settings specified for the “Erase” function? % Refer to “Erasing Specified Areas of Copies (“Erase” Functions)” on page 8-69. In addition. 8-34 im7520/im6020...
Page 295 Touch [OK], and then touch [OK] in the next screen that appears. In the Basic screen, touch [Paper], and then select the paper tray load- ed with the paper. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. im7520/im6020 8-35...
Page 296 SURVEYOR’S REPORT Scanning begins. What should be done if there are multiple pages in the original? % Position the next page and repeat step 11 until all pages of the doc- ument are scanned. 8-36 im7520/im6020...
Page 297 Application Functions After all original pages have been scanned, touch [Finish]. Press the [Start] key. Printing begins. im7520/im6020 8-37...
Page 298: Image Repeat
If the entire image does not fit within the specified area, the remaining areas are left blank as margins. Without Margin The number of repeating copies of the image is automatically detect- ed to completely fill the page. 8-38 im7520/im6020...
Page 299 Application Functions “With Margin” setting Original “Without Margin” setting 2 Repeat Original 4 Repeat Original 8 Repeat Original im7520/im6020 8-39...
Page 300: Auto Original Size Detect
3-7. Load the paper to be used into the desired paper tray. Touch [Application]. The Application screen appears. Touch [Book Copy/Repeat]. – To cancel all settings for the Application functions, touch [Reset]. The Book Copy/Repeat screen appears. 8-40 im7520/im6020...
Page 301 To cancel the “Image Repeat” function, touch [OFF]. The scanning area is detected, and the size appears under “Scan Range”. Check the scanning size under “Scan Range”, touch [OK], and then touch [OK] in the next screen that appears. im7520/im6020 8-41...
Page 302 In the Basic screen, touch [Paper], and then select the paper tray load- ed with the paper. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. 8-42 im7520/im6020...
Page 303: Set Range
Position the original to be copied. Load the paper to be used into the desired paper tray. Touch [Application]. The Application screen appears. Touch [Book Copy/Repeat]. – To cancel all settings for the Application functions, touch [Reset]. The Book Copy/Repeat screen appears. im7520/im6020 8-43...
Page 304 Application Functions Touch [Image Repeat]. The Image Repeat screen appears. Select the layout method. – To cancel changes to the settings, touch [Cancel]. – To cancel the “Image Repeat” function, touch [OFF]. 8-44 im7520/im6020...
Page 305 If a value outside the allowable range is specified, the message “In- put Error” appears. If “Input Error” appeared or if the value was in- correctly entered, press the [C] (clear) key to erase the value, and then specify the correct value. Touch [OK] three times. im7520/im6020 8-45...
Page 306 For details, refer to “To repeat the image the specified number of times (“Repeat”)” on page 8-47. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. 8-46 im7520/im6020...
Page 307: Repeat
Position the original to be copied. Load the paper to be used into the desired paper tray. Touch [Application]. The Application screen appears. Touch [Book Copy/Repeat]. – To cancel all settings for the Application functions, touch [Reset]. The Book Copy/Repeat screen appears. im7520/im6020 8-47...
Page 308 Range Original Size Setting”. Touch [2/4/8 Repeat]. – For details on specifying the repeating conditions, refer to “Repeat- ing the Copy Image on a Sheet of Paper (“Image Repeat” Function)” on page 8-38. The 2/4/8 Repeat screen appears. 8-48 im7520/im6020...
Page 309 [–] and [+] to specify the dimensions, and then touch [OK]. – If a decimal value is displayed in the screen, use the keypad to type in the setting. For details on switching between decimal and frac- tion values, refer to “System Setting” on page 12-14. im7520/im6020 8-49...
Page 310 In the Basic screen, touch [Paper], and then select the paper tray load- ed with the paper. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. 8-50 im7520/im6020...
Page 311 With single-sided copies, the pages are printed on two sheets of paper. With double-sided copies, the pages are printed on the front and back sides of a single sheet of paper. Reminder Position the original into the ADF. im7520/im6020 8-51...
Page 312: Booklet Pagination
For a document that exceeds 100 pages, refer “Scanning the Orig- inal in Separate Batches (“Separate Scan” Setting)” on page 3-11. Touch [Application]. The Application screen appears. Touch [Book Copy/Repeat]. – To cancel all settings for the Application functions, touch [Reset]. The Book Copy/Repeat screen appears. 8-52 im7520/im6020...
Page 313 To cancel changes to the settings, touch [Cancel]. – To cancel the “Booklet Pagination” function, touch [OFF]. Touch [OK] twice. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. im7520/im6020 8-53...
Page 314 “Right” setting “Left” setting “Top” setting Detail If the positions of the staples or punched holes are different from the binding position, the positions of the staples or punched holes are given priority. 8-54 im7520/im6020...
Page 315: Page Margin
For details on positioning the original, refer to “Positioning the Orig- inal” on page 3-7. Touch [Application]. The Application screen appears. Touch [Page Margin]. – To cancel all settings for the Application functions, touch [Reset]. The Page Margin screen appears. Specify the position of the filing margin. im7520/im6020 8-55...
Page 316 How can the entered margin position be corrected? % Without changing the margin width, change the margin position. Touch [OK]. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. 8-56 im7520/im6020...
Page 317: Edit Margin Setting
Place the original on the original glass. – For details on positioning the original, refer to “Positioning the Orig- inal” on page 3-7. Touch [Application]. The Application screen appears. Touch [Page Margin]. The Page Margin screen appears. im7520/im6020 8-57...
Page 318 For a horizontal shift, touch [Left] or [Right] to specify the shift di- rection. For a vertical shift, touch [Top] or [Bottom] to specify the shift direction. Both a horizontal shift and a vertical shift can be specified together. 8-58 im7520/im6020...
Page 319 If a value outside the allowable range is specified, the message “Input Error” appears. If “Input Er- ror” appeared or if the distance was incorrectly entered, press the [C] (clear) key to erase the value, and then specify the correct value. im7520/im6020 8-59...
Page 320 Touch [OK] three times. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. 8-60 im7520/im6020...
Page 321: Image Adjustment Settings
Normally, copies are produced with the image erased from the area 1/8 in from the top, 1/6 in from the bottom, and 1/16 in on each side. If “Full Scan” is selected, the image is copied to the edges of the paper without erasing the areas mentioned above. im7520/im6020 8-61...
Page 322 Application Functions “ Centering” selected “No Rotate” selected Normal copy “Full Scan” selected 8-62 im7520/im6020...
Page 323 For details on positioning the original, refer to “Positioning the Orig- inal” on page 3-7. Touch [Application]. The Application screen appears. Touch [Image Adjustment]. – To cancel all settings for the Application functions, touch [Reset]. The Image Adjustment screen appears. im7520/im6020 8-63...
Page 324 If a value outside the allowable range is specified, the message “In- put Error” appears. If “Input Error” appeared or if the distance was incorrectly entered, press the [C] (clear) key to erase the value, and then specify the correct value. 8-64 im7520/im6020...
Page 325 For details on switching between decimal and fraction values, refer to “System Setting” on page 12-14. Touch [OK] twice. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. im7520/im6020 8-65...
Page 326 3-68. For an original that exceeds 100 pages, refer “Scanning the Original in Separate Batches (“Separate Scan” Setting)” on page 3-11. The binding margin width is automatically specified. The “1>2” Simplex/Duplex setting is automatically selected. 8-66 im7520/im6020...
Page 327 Original” on page 3-7. Load the paper to be used into the desired paper tray. Touch [Application]. The Application screen appears. Touch [Booklet Pagination]. – To cancel all settings for the Application functions, touch [Reset]. The Booklet screen appears. im7520/im6020 8-67...
Page 328 Application Functions Touch [Left Bind] or [Right Bind]. Touch [OK]. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. 8-68 im7520/im6020...
Page 329: Erase Functions
Unwanted areas on all four sides of the original are erased. Center Erase Shading that appears along the center of the original is erased. Non-Image Area Erase The size of the original is detected, and any area not part of the orig- inal is erased. im7520/im6020 8-69...
Page 330: Erase
For details on positioning the original, refer to “Positioning the Orig- inal” on page 3-7. Touch [Application]. The Application screen appears. Touch [Erase]. – To cancel all settings for the Application functions, touch [Reset]. The Erase screen appears. 8-70 im7520/im6020...
Page 331 To specify that no part of a side is to be erased, touch [None]. – Touch [↔] to switch between the integer and the fraction, touch[–] and [+] to specify the width to be erased, and then touch [OK]. im7520/im6020 8-71...
Page 332 Touch [OK], and then touch [OK] in the next screen that appears. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. 8-72 im7520/im6020...
Page 333: Center Erase
For details on positioning the original, refer to “Positioning the Orig- inal” on page 3-7. Touch [Application]. The Application screen appears. Touch [Erase]. – To cancel all settings for the Application functions, touch [Reset]. The Erase screen appears. im7520/im6020 8-73...
Page 334 – To cancel the “Center Erase” function, touch [OFF]. – To cancel changes to the settings, touch [Cancel]. Touch [OK] twice. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. 8-74 im7520/im6020...
Page 335: Non-Image Area Erase
Be sure to fully open the ADF before making copies, otherwise the copies will not be produced correctly. Touch [Application]. The Application screen appears. Touch [Erase]. – To cancel all settings for the Application functions, touch [Reset]. The Erase screen appears. im7520/im6020 8-75...
Page 336 If necessary, specify any other copy settings. – Be sure to fully open the ADF before making copies, otherwise the copies will not be produced correctly. Using the keypad, type in the desired number of copies. Press the [Start] key. 8-76 im7520/im6020...
Page 337 Print copies with one of the preset stamps, such as “URGENT” or “IMPORTANT”. (Refer to page 8-90.) Watermark Print copies with one of the preset text. (Refer to page 8-92.) If the HDD is not installed, “Set Numbering” function is not available. im7520/im6020 8-77...
Page 338 Application Functions ‘05/1/23 1:23PM Date/Time Page # Print Position URGENT 0001 0001 0001 0001 0001 0001 0001 0001 Built-in Stamp Set Numbering 8-78 im7520/im6020...
Page 339 For details on positioning the original, refer to “Positioning the Orig- inal” on page 3-7. Touch [Application]. The Application screen appears. Touch [Stamp/Overlay]. – To cancel all settings for the Application functions, touch [Reset]. The Stamp/Overlay screen appears. im7520/im6020 8-79...
Page 340 Application Functions Select the desired Stamp function. – The Stamp functions can be used together. 8-80 im7520/im6020...
Page 341 Touch the buttons for the desired settings under “Date Type”, “Time Type” and “Pages”. – To cancel changes to the settings, touch [Cancel]. – To cancel the “Date/Time” function, touch [OFF]. Can the time be omitted? % If “None” is selected, the time is not printed. im7520/im6020 8-81...
Page 342 “Top & Bottom Adjustment”, and then use the keypad or touch [-] and [+] to specify the adjustment amount. – When using the keypad to specify the settings, press the [C] (clear) key, and then type in the setting. 8-82 im7520/im6020...
Page 343: Page Number
Printing the Page Number (“Page #” function) To copy using the “Page #” function In the Stamp/Overlay screen, touch [Page #]. – For details on displaying the Stamp/Overlay screen, refer to “To display the Stamp/Overlay screen” on page 8-79. The Page # screen appears. im7520/im6020 8-83...
Page 344 To cancel the “Page #” function, touch [OFF]. Specify the page number type. – To specify settings for cover pages and insertion sheets or if there are inserted pages, continue with step 4. – If there are no insertion sheets, skip to step 6. 8-84 im7520/im6020...
Page 345 “Skip the page(s)” is selected, the page number is not counted and the page is left blank. The sheet setting screen appears. To specify settings for the pages to be printed on, and then touch [OK]. The Page # screen appears again. im7520/im6020 8-85...
Page 346 “Top & Bottom Adjustment”, and then use the keypad or touch [-] and [+] to specify the adjustment amount. – When using the keypad to specify the settings, press the [C] (clear) key, and then type in the setting. 8-86 im7520/im6020...
Page 347 % To make no left/right or up/down adjustments, touch [No Adj.]. Touch [OK]. The Print Position screen appears. Touch [OK] two times. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. im7520/im6020 8-87...
Page 348: Numbering
The distribution number is normally printed as a four-digit number. If “Start Number” is set to “1”, “0001” is printed. – To cancel changes to the settings, touch [Cancel]. – To cancel the “Set Numbering” function, touch [OFF]. 8-88 im7520/im6020...
Page 349 Touch a button under “Text Density” and “Pages” to specify the de- sired settings. Touch [OK] twice. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. im7520/im6020 8-89...
Page 350: Built-In Stamp
For details on displaying the Stamp/Overlay screen, refer to “To display the Stamp/Overlay screen” on page 8-79. The Built-In Stamp screen appears. Select the preset stamp. – To cancel changes to the settings, touch [Cancel]. – To cancel the “Built-In Stamp” function, touch [OFF]. 8-90 im7520/im6020...
Page 351 [C] (clear) key to erase the value, and then specify the cor- rect value. Touch [OK] four times. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. im7520/im6020 8-91...
Page 352: Watermark
To cancel changes to the settings, touch [Cancel]. – To cancel the “Watermark” function, touch [OFF]. Touch [OK] twice. The Watermark screen appears again. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. 8-92 im7520/im6020...
Page 353: Energy Star
“low-power mode” after a period of inactivity. An ENERGY ® STAR product uses energy more efficiently, saves you money on utility bills and helps protect the environment. im7520/im6020...
Page 354 Introduction ACKNOWLEDGEMENTS: Imagistics and the Imagistics Logo are trademarks of Imagistics International Inc., registered in the U.S. Patent and Trademark office and/or other jurisdic- tions. Copyright © 2005 Imagistics International Inc. EXEMPTION No part of this manual may be used or duplicated without permision.
Page 355: Managing Jobs
Programming copy settings ............x-23 Checking the copy settings ............x-23 Enlarging the size of text in touch panel screens ......x-23 Displaying explanations of functions and settings ......x-23 Interrupting a copy job ..............x-23 Printing a sample copy ..............x-23 Explanation of Manual Conventions ..........x-24 im7520/im6020...
Page 356 Part Names and Their Functions .............2-2 Outside of Machine .................2-2 Inside of Machine ................2-5 Options ...................2-6 Large Capacity Tray LU-401/LU-402 ..........2-8 Finisher FS-504/FS-602 (+ Punch Kit PK-505) .......2-9 Cover Sheet Feeder PI-501 ............2-11 Z-Folding unit ZU-602 ..............2-12 Shift Tray SF-601 ................2-13 im7520/im6020...
Page 357 Operations where the setting specified last is given priority ..3-5 Operations where the setting specified first is given priority ..3-6 Positioning the Original ..............3-7 To position the original into the ADF ..........3-7 To position the original on the original glass ......... 3-9 im7520/im6020...
Page 358 To specify an Orig. Image Type setting ........3-46 Specifying the Density Settings .............3-47 Adjusting the Print Density (Density Settings) ......3-48 Adjusting the Background Density (Adjust Background Settings) ............3-49 3.10 Selecting a Combine Originals Setting ..........3-50 Copying Multiple Original Pages Onto a Single Page (Combine Originals) ..............3-52 im7520/im6020...
Page 359 To recall a stored job ..............4-14 Displaying Function Descriptions (Help) ........4-17 Overview of Help Screens ............4-17 To display the Main Help Menu screen ........4-20 To display the Help screen while specifying a setting ....4-22 im7520/im6020...
Page 360 ADF ....................6-3 Option Specifications ..............6-5 Large Capacity Tray LU-401 ............6-5 Large Capacity Tray LU-402 ............6-5 Finisher FS-504 ................6-6 Finisher FS-602 ................6-6 Punch Kit PK-505 ................6-7 Z-Folding Unit ZU-602 ..............6-8 Cover Sheet Feeder PI-501 ............6-8 Shift Tray SF-601 ................6-8 Accessories ..................6-9 im7520/im6020...
Page 361 Inserting Paper Between Overhead Projector Transparencies (“OHP Interleave” Function) ............. 8-2 To copy using the “OHP Interleave” function ........ 8-3 Inserting Copies of a Different Original at a Specified Location (“Insert Image” Function) ..............8-6 To copy using the “Insert Image” function ........8-8 im7520/im6020...
Page 362 (“Non-Image Area Erase” function) ..........8-75 8.14 Printing the Date/Time, Page Number or Distribution Number on Copies (Stamp/Overlay Functions) ..........8-77 To display the Stamp/Overlay screen ...........8-79 Printing the Date/Time (“Date/Time” function) ......8-81 To copy using the “Date/Time” function ........8-81 x-10 im7520/im6020...
Page 363: Replacing Toner Cartridges And Staples And Emptying Dust Boxes
Control Panel ................10-4 ADF platen guide cover ..............10-4 Paper Take-Up Roller ..............10-5 10.2 Viewing Counters (Meter Count) ........... 10-6 To view the counters ..............10-6 10.3 When the Message “Preventive maintenance time.” Appears ... 10-7 im7520/im6020 x-11...
Page 364: Destination Register
Specifying Administrator Settings ..........12-26 System Setting ................12-26 Administrator/Machine Setting ...........12-32 One-Touch Registration ..............12-32 User Authentication/Account Track ..........12-33 Network Setting ................12-35 Copier Setting ................12-35 Printer Setting ................12-36 System Connection ..............12-37 Security Setting ................12-37 Displaying the Administrator Setting Screen ......12-39 x-12 im7520/im6020...
Page 365: Im7520/Im6020
To check the counter ..............12-84 12.9 Account Track Setting ..............12-86 Account Track Registration ............12-86 Account Track Counter .............. 12-90 To check the counter ..............12-91 12.10 Password Rules ................12-92 Conditions of the password rules ..........12-92 im7520/im6020 x-13...
Page 366: Function Combinations
Introduction 13 Appendix 13.1 Entering Text ..................13-2 To type text ...................13-4 List of Available Characters ............13-4 13.2 Function Combination Table ............13-5 Function Combination Table ............13-5 14 Index 14.1 Index ....................14-2 x-14 im7520/im6020...
Page 367: Available Features
Scan” Setting)” on page 3-11. Copying an original containing various page sizes An original with various page sizes can be scanned and copied together. For details, refer to “Copying Original of Mixed Sizes (“Mixed Original” Set- ting)” on page 3-15. im7520/im6020 x-15...
Page 368: Specifying Separate Horizontal And Vertical Zoom Ratios
Copying multiple Original pages onto a single page Multiple pages of the original can be printed together on a single page. For details, refer to “Copying Multiple Original Pages Onto a Single Page (Combine Originals)” on page 3-52. ABC DEF x-16 im7520/im6020...
Page 369: Sorting Copies
Copies can be stapled together before they are fed out. For details, refer to “Stapling Copies (Staple Settings)” on page 3-59. Punching holes in copies Holes for filing can be punched in the copies. For details, refer to “Punching Holes in Copies (Punch Settings)” on page 3-63. im7520/im6020 x-17...
Page 370: Center Folding/Binding
Inserting paper between copies of overhead projector transparencies After each overhead projector transparency copy is printed, a page can be added to the stack as an interleaf. For details, refer to “Inserting Paper Between Overhead Projector Transpar- encies (“OHP Interleave” Function)” on page 8-2. x-18 im7520/im6020...
Page 371: Inserting Copies Of A Different Original At A Specified Location
Copying with chapter title pages on the front side Double-sided copies can be made so that the chapter title pages are printed on the front sides of pages. For details, refer to “Specifying Pages To Be Printed on the Front Side (“Chapters” Function)” on page 8-22. im7520/im6020 x-19...
Page 372: Copying With Reversed Colors
Spread (“Book Copy” Function)” on page 8-30. Repeating copy images image can be repeatedly printed on a single sheet of paper. original For details, refer to “Repeating the Copy Image on a Sheet of Paper (“Image Repeat” Function)” on page 8-38. x-20 im7520/im6020...
Page 373: Splitting An Original Page Into Two Copies
Adjusting the image to fit the paper size Copies can be produced after specifying the position of the original image on the paper. For details, refer to “Adjusting the Image To Fit the Paper (Im- age Adjustment Settings)” on page 8-61. im7520/im6020 x-21...
Page 374: Copying With A Layout For Center Binding
For details, refer to “Printing the Date/Time, Page Number or Distribution Number on Copies (Stamp/Overlay Functions)” on page 8-77. Managing jobs The print status of copy jobs can be checked and the jobs can be managed. For details, refer to “Managing Jobs (Job List)” on page 11-2. x-22 im7520/im6020...
Page 375: Programming Copy Settings
The text and buttons in the touch panel can be displayed in a larger size that is easier to read, allowing basic copy operations to be easily performed. For details, refer to the Enlarge Display Operations of the im7520/im6020 User’s Guide.
Page 376: Explanation Of Manual Conventions
Text highlighted in this manner indicates precautions to ensure safe use of this machine. "Warning" indicates instructions that, when not observed, may result in fatal or critical injuries. "Caution" indicates instructions that, when not observed, may result in serious injuries or property damage. (The page shown above is an example only.) x-24 im7520/im6020...
Page 377: Descriptions And Symbols For Original And Paper
“Y” in the illustration) and the second to the length (shown as “X”). Paper Orientation Lengthwise (w) If the width (Y) of the paper is shorter than the length (X), the paper has a vertical or portrait orientation, indicated by w. im7520/im6020 x-25...
Page 378 Introduction Crosswise (v) If the width (Y) of the paper is longer than the length (X), the paper has a horizontal or land- scape orientation, indicated by v. x-26 im7520/im6020...
Page 379: User's Guides
User’s Guide [Enlarge Display Operations] This manual contains details on operating procedures for using copy func- tions in Enlarge Display mode. - Refer to this User’s Guide for details on operating procedures in Enlarge Display mode. im7520/im6020 x-27...
Page 380: Legal Restrictions On Copying
In addition, it is prohibited under any circumstances to copy domestic or for- eign currencies, or works of art without permission of the copyright owner. When in doubt about the nature of a document, consult with legal counsel. x-28 im7520/im6020...
Page 381: Installation And Operation Precautions
Installation and Operation Precautions...
Page 382: Utility
This symbol warns against cause burns. A diagonal line indicates a prohibited course of action. This symbol warns against dismantling the device. A solid circle indicates an imperative course of action. This symbol indicates you must unplug the device. im7520/im6020...
Page 383 Should any of these conditions be found, im- mediately turn OFF the power switch, unplug the power cord from the power outlet, and then call your authorized service representative. im7520/im6020...
Page 384 Overload could result in a fire. CAUTION • The outlet must be near the equipment and easily accessible. Otherwise you can not pull out the power plug when an emergency occurs. im7520/im6020...
Page 385: Grounding
Dust that accumu- lates between the plug terminals may cause a fire. Grounding WARNING • Connect the power cord to an electrical outlet that is equipped with a grounding terminal. im7520/im6020...
Page 386 • Do not let any object plug the ventilation holes of this product. Heat could accumulate inside the product, resulting in a fire or malfunction. • Do not use flammable sprays, liquids, or gases near this product, as a fire could result. im7520/im6020...
Page 387 When checking the inside of the unit for mal- functions such as a paper misfeed, do not touch the locations (around the fusing unit, etc.) which are indicated by a “Caution HOT” cau- tion label. im7520/im6020...
Page 388 If the unit falls it may cause severe personal injury. The product may also be damaged or malfunction. Before successive holidays CAUTION • Unplug the product when you will not use the product for long periods of time. im7520/im6020...
Page 389: Regulation Notices
FCC rules. INTERFERENCE-CAUSING EQUIPMENT STANDARD (ICES-003 ISSUE 4) (For Canada Users) This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. im7520/im6020...
Page 390: For Users In Countries Not Subject To Class B Regulations
Dersom apparatet brukes på annen måte enn spesifisert I denne bruksan- visning, kan brukeren utsettes for usynlig laserstråling som overskrider grensen for laser klass 1. Dette en halvleder laser. Maksimal effekt till laserdiode er 15 mW og bøkge- lengde er 770 - 800 nm. 1-10 im7520/im6020...
Page 391 överskrider gränsen för laserklass 1. Det här är en halvledarlaser. Den maximala effekten för laserdioden är 15 mW och våglängden är 770 - 800 nm. Rear side of main body im7520/im6020 1-11...
Page 392: Ozone Release
Acoustic noise (For European Users Only) Maschinenlärminformations-Verordnung 3. GPSGV: Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779. 1-12 im7520/im6020...
Page 393: Caution Notations And Labels
High voltage is present around this part. DO NOT put your hand Do not touch this part between the main body and in order to reduce the risk developing fixing unit; of electric shock. otherwise you may be injured. im7520/im6020 1-13...
Page 394: Space Requirements
Installation and Operation Precautions Space Requirements To ensure that machine operation, consumables replenishing, part replace- ment, and regular maintenance can easily be performed, adhere to the rec- ommended space requirements detailed below. im7520/im6020 im7520/im6020 + 9209 1-14 im7520/im6020...
Page 395 Installation and Operation Precautions im7520/im6020 + 9204 + 9262 + 9263 im7520/im6020 + 9204 + 9262 + 9209 Reminder Be sure to allow a clearance of 200 mm (7-3/4 in.) or more at the back of this machine for the ventilation duct.
Page 396: Operation Precautions
- Copies that are to be kept for a long time should be kept where they are not exposed to light in order to prevent them from fading. - Adhesive that contains solvent (e.g., spray glue) may dissolve the toner on copies. 1-16 im7520/im6020...
Page 397: Before Making Copies
Before Making Copies...
Page 398: Part Names And Their Functions
Before Making Copies Before Making Copies Part Names and Their Functions Outside of Machine im7520/im6020...
Page 399: Exit Tray
2-14.) Front doors (left and right) Opened when clearing paper misfeeds Exit tray Collects printed pages Note The maximum angle that the ADF is opened can be adjusted in two stag- es. For details, contact your technical representative. im7520/im6020...
Page 400: Network Connector
Description Power cord Supplies power to the machine Serial port (RS-232C) Used for transmissions with CS Remote Care Network connector (10Base-T/ Used for connecting the network cable when this 100Base-TX) machine is used for network printing and network scanning im7520/im6020...
Page 401: Inside Of Machine
Used to turn the machine on and off Total counter Shows the total number of pages that have been printed Reminder Parts in the fusing unit are extremely hot. Touching any part in this unit may result in burns. im7520/im6020...
Page 402: Options
Before Making Copies Options im7520/im6020...
Page 403: Key Counter
Referred to as the “hard disk” or “HDD” throughout the manual. Printer controller im6020020 Allows this machine to be used as a network printer (optional) Local interface kit im6020070 Used for making a local connection between this machine and the computer im7520/im6020...
Page 404 Bottom-plate-lowering button Pressed to lower the bottom plate in the tray to load paper Bottom plate Raised as the paper is used. Lower by pressing the bottom-plate-lowering button. Trailing-edge guide Positions the trailing edge of the paper to be load- im7520/im6020...
Page 405: Replacing The Staple Cartridge
BM tray Collects pages printed with the “Half Fold”, “Fold & Staple”, or “Tri-Fold” settings or with the “Cover Mode” function Main tray Collects printed pages Sub tray Collects printed pages im7520/im6020...
Page 406: Stacker Unit
Punch settings (See p. 9-15.) Stacker unit handle Used to pull out the unit when clearing paper mis- feeds in the stacker unit and when refilling the sta- ples Staple cartridge Removed when refilling the staples (See p. 9-7.) 2-10 im7520/im6020...
Page 407: Cover Sheet Feeder Pi-501
Slide to fit the size of paper being loaded when loading with cover sheets. Upper tray Load with cover sheets. Lower tray Load with cover sheets. Lower tray paper guide Slide to fit the size of paper being loaded when loading with cover sheets. im7520/im6020 2-11...
Page 408 Used to pull out the unit when clearing paper mis- feeds paper misfeeds Opened when clearing paper misfeeds Punch dust box Removed when emptying punch dust that has ac- cumulated from using the Punch settings (See p. 9-17.) 2-12 im7520/im6020...
Page 409 Before Making Copies Shift Tray 9207 Part Name Description Exit tray Collects printed pages Upper cover Opened when clearing paper misfeeds im7520/im6020 2-13...
Page 410: Access Key
Press to enter Box mode. While the machine is in Box mode, the indicator on the [Box] key lights up in green. For details, refer to the Box Operations of the im7520/im6020 User’s Guide. [Fax] key Press to enter Fax mode.
Page 411: Accessibility Key
[Accessibility] key Press to display the screen for specifying user accessibility functions. [Help] key Press to display the Main Help Menu screen, where descriptions of the various functions and details of operations can be displayed. (See p. 4-17.) im7520/im6020 2-15...
Page 412 Do not apply extreme pressure to the touch panel, otherwise it may be scratched or damaged. Never push down on the touch panel with force, and never use a hard or pointed object to make a selection in the touch panel. 2-16 im7520/im6020...
Page 413: Basic Settings Screen (Basic Screen)
[Finishing] key Touch to specify settings for sort, group, offset, stapling, or hole punching. (See p. 3-53.) [Folding] key Touch to specify the function for folding and bind- ing pages, tri-fold folding, zigzag (Z-Flod) folding. im7520/im6020 2-17...
Page 414: Icons That Appear In The Touch Panel
Various commands are available to specify the box where the data is to be saved and whether or not the data is printed when it is saved. For details, re- fer to the Box Operations of the im7520/im6020 User’s Guide. [Separate Scan] key Touch to scan the original in separate batches.
Page 415: Toner Cartridge
Indicates that less than 25% of the paper remains in the paper tray Indicates that no paper remains in the paper tray Indicates that the toner cartridge must be replaced Indicates the orientation in which the original is positioned im7520/im6020 2-19...
Page 416: Adjusting The Angle Of The Control Panel
The control panel can be adjusted to either of two angles. Adjust the control panel to the angle that allows for easy operation. To adjust the angle of the control panel Press the control panel release lever, and then push down on the con- trol panel. 2-20 im7520/im6020...
Page 417 To return the control panel to the upper posi- tion, press the control panel release lever, and then pull up on the con- trol panel. Note The control panel can also be grabbed anywhere on its outer edge and lifted. im7520/im6020 2-21...
Page 418: Turning On The Main Power And The Sub Power
Open the front door on the left side. The main power switch is on the left side inside the machine. Turn on the main power switch. The indicator on the main power switch lights up in green. 2-22 im7520/im6020...
Page 419 Note A job can also be queued while the machine is warming up after the sub power switch is turned on. For details, refer to “To scan during warm-up” on page 2-24. im7520/im6020 2-23...
Page 420: To Scan During Warm-Up
Specify any necessary copy settings. Using the keypad, specify the desired number of copies. How is the number of copies specified? % For details on specifying the number of copies, refer to “General Copy Operation” on page 3-2. 2-24 im7520/im6020...
Page 421 After the machine has finished warming up, the scanned image will be printed. The machine takes about 5 minutes (im7520)/4 minutes 30 seconds (im6020) to warm up at normal room temperature (68°F) when the control panel is turned on using the sub power switch after the machine is turned on using the main power switch.
Page 422: To Turn Off The Machine
Do not turn off the machine with the main power switch while a queued job or stored data is waiting to be printed, otherwise the jobs will be deleted. 2-26 im7520/im6020...
Page 423: Automatically Canceling The Settings (Automatic Panel Reset)
As the factory default, the Copy mode screen is displayed after 1 minute. Detail The mode screen that is displayed when the automatic system reset op- eration is performed can be changed from the Utility mode. For details, refer to “System Setting” on page 12-14. im7520/im6020 2-27...
Page 424: Automatically Conserving Energy (Low Power Mode)
For details, refer to “System Setting” on page 12-14, page 12-26. If the time for entering Low Power mode and Sleep mode are the same, the machine will immediately enter Sleep mode without entering Low Power mode. 2-28 im7520/im6020...
Page 425: Automatically Conserving Energy (Sleep Mode)
Low Power mode if no operation is performed for 15 minutes, and then the machine enters Sleep mode after 90 minutes have elapsed. The length of time until the machine enters Sleep mode can be changed. For details, refer to “System Setting” on page 12-26. im7520/im6020 2-29...
Page 426: Manually Conserving Energy
Low Power mode. Detail Whether the machine enters Low Power mode or Sleep mode when the [Power Save] key is pressed can be set from the Administrator mode. For details, refer to “System Setting” on page 12-26. 2-30 im7520/im6020...
Page 427: Limiting Machine Usage According To A Schedule (Weekly Timer)
Type in the password (up to 8 digits) for non-business hours. How is the password for non-business hours specified? % For details on specifying the password for non-business hours, re- fer to “System Setting” on page 12-26. Touch [OK]. im7520/im6020 2-31...
Page 428 From Administrator mode, the machine can be set so that the screen for entering the password for non-business hours is not displayed. The default setting for the “Password for Non-Business Hours” parame- ter is “OFF” (the screen is not displayed). 2-32 im7520/im6020...
Page 429: Controlling The Use Of This Machine With User Authentication
0 When user authentication has been set, only users that enter passwords for specified accounts can use this machine. 0 Contact your administrator for account passwords. 0 A total of 1000 users and accounts can be registered. Touch [User Name]. Type in the user name, and then touch [OK]. im7520/im6020 2-33...
Page 430 Before Making Copies Touch [Password]. Type in the password, and then touch [OK]. Press the [Access] key. The input screen disap- Access pears, and the Basic screen appears. Make copies using the desired copy settings. 2-34 im7520/im6020...
Page 431 If [Public User Access] appears, users with no access to a user name and password can touch [Public User Access] to use this machine. Note If account track settings have been applied, a screen for entering account information appears. im7520/im6020 2-35...
Page 432: Using The Machine With Account Track
0 A total of 1000 users and accounts can be registered. Touch [Account Name]. – If the Administrator mode settings have been set to “Password On- ly”, touch [Input], and then continue with step 4. Type in the account name, and then touch [OK]. 2-36 im7520/im6020...
Page 433 Before Making Copies Touch [Password]. Type in the password, and then touch [OK]. Press the [Access] key. The input screen disap- Access pears, and the Basic screen appears. Make copies using the desired copy settings. im7520/im6020 2-37...
Page 434 When you are finished printing, press the [Access] key. A message appears, requesting confirmation to log off. Touch [Yes]. Authentication screen appears again. Detail For details on specifying account track settings, refer to “User Authenti- cation/Account Track” on page 12-33. 2-38 im7520/im6020...
Page 435: Loading Paper Into The Tray 1 Or 2
Pull out the paper tray for the tray 1 or 2. Raise the paper take-up roller. Load the paper into the tray. – Load the paper so that it is flush against the right side of the tray. im7520/im6020 2-39...
Page 436 If there is space between the trailing-edge guide and the paper, the paper will not be fed correctly. Do not close the paper tray with too much force, otherwise the weight of the tray and paper will apply an impact to the machine that may cause damage. 2-40 im7520/im6020...
Page 437: Loading Paper Into The Tray 3 Or 4
Pull out the paper tray for the tray 3 or 4. Raise the paper take-up roller. Load the paper into the tray. – Load the paper so that it is flush against the right side of the tray. im7520/im6020 2-41...
Page 438 If custom-sized paper is loaded, there may be some space between the paper and the trailing-edge guide. When loading the paper, make sure that it fits well against the right side of the paper tray, not the trailing-edge guide. 2-42 im7520/im6020...
Page 439 Before Making Copies Reminder Do not close the paper tray with too much force, otherwise the weight of the tray and paper will apply an impact to the machine that may cause damage. im7520/im6020 2-43...
Page 440: Loading Paper Into The Bypass Tray
Inkjet printer paper To load paper (bypass tray) Open the bypass tray. – Open the bypass tray to the right, and then open the folded tray to the right. Insert the paper as much as possible into the feed slot. 2-44 im7520/im6020...
Page 441 “5.5 × 8.5 A5 Thick paper” in order to prevent paper misfeeds. For details on setting the conveyance lever to “5.5 × 8.5 A5 Thick paper”, refer to “When Thick Paper Is Loaded Into a Paper Tray” on page 2-53. im7520/im6020 2-45...
Page 442 Load overhead projector transparencies one sheet at a time. Reminder When loading tab paper, load them in the v orientation, as shown in the illustration. Do not load label sheets in the w orientation. 2-46 im7520/im6020...
Page 443 Be sure to load letterhead paper so that the side to be printed on faces Note The image will be printed on the surface of the paper facing down when the paper is loaded into the bypass tray. im7520/im6020 2-47...
Page 444: Loading Paper Into The Lct (Lu-401/Lu-402)
To load paper (LCT) Open the upper door of the large capacity tray. Press the bottom- (9208) plate-lowering button. – The bottom plate is lowered. (9209) 2-48 im7520/im6020...
Page 445 Before Making Copies Load the paper into the (9208) tray. (9209) im7520/im6020 2-49...
Page 446 Do not load so much paper that the top of the stack does not exceed the, mark. Make sure that the trailing-edge guide is adjusted to fit the size of the loaded paper. If there is space between the trailing-edge guide and the paper, the paper will not be fed correctly. 2-50 im7520/im6020...
Page 447: Loading Paper Of A Different Size Into Paper Trays
Remove the trailing-edge guide, and then insert it at the position for the desired paper size. – Press the button to remove the trailing- edge guide. – Insert the trailing- edge guide into the hole correspond- ing to the size indi- cated on the bottom plate. im7520/im6020 2-51...
Page 448 – If non-standard-sized paper, thick paper, tab paper, or special pa- per was loaded, specify the settings for the loaded paper in the Pa- per Type screen. Refer to “Specifying Paper Settings for Paper Trays” on page 7-22. 2-52 im7520/im6020...
Page 449: When Thick Paper Is Loaded Into A Paper Tray
To set the conveyance lever Open the front doors (left and right). Turn lever M4 to the left, and then pull out the ADU unit. Lever M4 im7520/im6020 2-53...
Page 450 Set the conveyance lever to “5.5 × 8.5 A5 Thick paper”. Conveyance lever Return the ADU unit to its original position. Close the front doors (left and right). Note After using thick paper, be sure to reset the conveyance lever to “NOR- MAL”. 2-54 im7520/im6020...
Page 451: Basic Copy Operations
Basic Copy Operations...
Page 452: General Copy Operation
3-5. To make a copy Press the [Copy] key to display the Basic screen in Copy mode. Position the original to be copied. – For details on positioning the original, refer to “Positioning the Orig- inal” on page 3-7. im7520/im6020...
Page 453 For details on selecting Finishing settings, refer to “Selecting Fin- ishing Settings” on page 3-53. – For details on specifying the “Folding” function, refer to “Specifying Folding Settings” on page 3-66. – For details on specifying settings for the Application functions, refer to “Application Functions” on page 8-2. im7520/im6020...
Page 454 The next copy opera- tion can be queued while a copy opera- tion is being per- formed. For details, refer to “Scanning the Next Original To Be Copied While a Copy Job Is Being Printed (Next Job Reservation)” on page 3-72. im7520/im6020...
Page 455: Operations That Cannot Be Combined
Select the “2 Position” Staple setting. Set the “Booklet” function. The “2 Position” Staple setting is automatically cancelled, and the “Booklet” function is set. To select the “2 Position” Staple setting, cancel the “Booklet” function, and then select the “2 Position” setting. im7520/im6020...
Page 456: Operations Where The Setting Specified First Is Given Priority
“2 Position” Staple setting cannot be selected. The “Booklet” function remains selected and the “2 Position” Staple setting is canceled. To select the “2 Position” Staple setting, cancel the “Booklet” function, and then select the “2 Position” setting. im7520/im6020...
Page 457: Positioning The Original
Position the original face up in the ADF. – Position the original pages so that the top of the original is to- ward the back or the right side of the ma- chine. im7520/im6020...
Page 458 For details on selecting the original orientation, refer to “Selecting the Original Orientation (Original Direction Settings)” on page 3-20. – For details on selecting the position of the binding margin, refer to “Selecting the Position of the Binding Margin (Margin Settings)” on page 3-22. im7520/im6020...
Page 459: To Position The Original On The Original Glass
Position the original face down onto the original glass. – Load the document pages so that the top of the original is toward the back or the left side of the machine. When loaded in the When loaded in the v orientation: w orientation: im7520/im6020...
Page 460 Close the ADF. 3-10 im7520/im6020...
Page 461: Scanning The Original In Separate Batches ("Separate Scan" Setting)
When using the ADF, load the original with the pages in order and the first page on top. Up to 100 sheets can be loaded at one time. In the Basic screen, touch [Separate Scan]. – To cancel the “Separate Scan” setting, touch [Separate Scan] again to deselect it. im7520/im6020 3-11...
Page 462 To delete the image data, press the [Stop] key, and then delete the job. For details, refer to “Stopping Scanning/Printing” on page 3-74. After the original is scanned, the message “Scanning stopped. Press [Start] to continue.” appears. After all original pages have been scanned, touch [Finish]. Press the [Start] key. 3-12 im7520/im6020...
Page 463: Scanning A Multi-Page Original From The Original Glass
For details on positioning the original, refer to “To position the orig- inal on the original glass” on page 3-9. When loaded in the When loaded in the v orientation: w orientation: Close the ADF. In the Basic screen, touch [Simplex/Duplex]. The Simplex/Duplex screen appears. im7520/im6020 3-13...
Page 464 Position the second page or second side of the original onto the origi- nal glass, and then press the [Start] key. – To scan the remaining pages in the original, repeat steps 7. After all original pages have been scanned, touch [Finish]. Press the [Start] key. 3-14 im7520/im6020...
Page 465: Specifying Original Settings
(first page) faces up, as shown in the illus- tration. – For details on the original sizes that can be mixed in the ADF, refer to “Origi- nal That Can Be Po- sitioned into the ADF” on page 7-33. im7520/im6020 3-15...
Page 466 In the Basic screen, touch [Combine Originals]. The Combine Originals screen appears. Touch [Mixed Original]. – To cancel the “Mixed Original” setting, touch [Mixed Original] again to deselect it. 3-16 im7520/im6020...
Page 467: Positioning Folded (Z-Folded) Original
Position the original to be copied. – For details on load- ing the original, refer to “To position the original into the ADF” on page 3-7. In the Basic screen, touch [Combine Originals]. The Combine Originals screen appears. im7520/im6020 3-17...
Page 468: Positioning Tabbed Original
Tabbed paper can be loaded into the 3rd or 4th tray or the bypass tray. – For details, refer to “Specifying Paper Settings for Paper Trays” on page 7-22 or “Loading Paper Into the Bypass Tray” on page 2-44. 3-18 im7520/im6020...
Page 469 Basic Copy Operations In the Basic screen, touch [Combine Originals]. The Combine Originals screen appears. Touch [Tab Original]. The Tab Original Size screen appears. Touch the button for the size of the positioned original. Touch [OK]. im7520/im6020 3-19...
Page 470: Selecting The Original Orientation (Original Direction Settings)
ADF with the top of the original toward the right side of this machine. • Select this setting for an original placed on the original glass with the top of the original toward the left side of this machine. 3-20 im7520/im6020...
Page 471: To Specify An Original Direction Setting
0 For details on positioning the document, refer to “Positioning the Origi- nal” on page 3-7. Position the original to be copied. In the Basic screen, touch [Combine Originals]. The Combine Originals screen appears. Touch [Original Direction]. The Original Direction screen appears. im7520/im6020 3-21...
Page 472: Selecting The Position Of The Binding Margin (Margin Settings)
To cancel changes to the settings, touch [Cancel]. Selecting the Position of the Binding Margin (Margin Settings) If the original loaded into the ADF is double-sided, specify the binding posi- tion of the document. Note The default setting is “Auto”. 3-22 im7520/im6020...
Page 473 If the original length is more than 11-11/ 16in. a binding position along the short side A B C of the paper is selected. When the original length is more than 11-11/16in. : A B C im7520/im6020 3-23...
Page 474: To Specify A Margin Setting
When loading an original with a binding margin, position the top of the original toward the back of the machine. In the Basic screen, touch [Combine Originals]. The Combine Originals screen appears. Touch [Margin]. The Page Margin screen appears. 3-24 im7520/im6020...
Page 475 Basic Copy Operations Touch the button for the desired margin position, and then touch [OK]. – To cancel changes to the settings, touch [Cancel]. im7520/im6020 3-25...
Page 476: Selecting A Paper Setting
If the “×1.0” Zoom setting was specified, paper of the same size as the orig- inal is selected. If the zoom ratio was increased or decreased, a paper size that corresponds to the specified zoom ratio is automatically selected. 3-26 im7520/im6020...
Page 477 Basic Copy Operations In the Basic screen, touch [Paper]. The Paper screen appears. Touch [Auto Paper Select]. Touch [OK]. The Basic screen appears again. im7520/im6020 3-27...
Page 478: Manually Selecting The Desired Paper Size
For details, refer to “Icons That Appear in the Touch Panel” on page 2-18 In the Basic screen, touch [Paper]. The Paper screen appears. Select the paper tray loaded with the desired paper. Touch [OK]. The Basic screen appears again. 3-28 im7520/im6020...
Page 479: Specifying A Zoom Setting
If the “Auto Paper Select” setting was selected, the Paper screen appears. In the Paper screen, specify the desired Paper setting. In the Basic screen, touch [Zoom]. The Zoom screen appears. Touch [Auto Zoom]. Touch [OK]. The Basic screen appears again. im7520/im6020 3-29...
Page 480: Specifying The Same Zoom Ratio As The Original ("×1.0" Setting)
0 Touch [+] to enlarge the zoom ratio, and touch [–] to reduce the zoom ra- tio in ×0.001 intervals. In the Basic screen, touch [Zoom]. The Zoom screen appears. Touch [×1.0]. Touch [OK]. The Basic screen appears again. 3-30 im7520/im6020...
Page 481: Slightly Reducing The Copy ("Minimal" Setting)
×0.999). For details on changing the zoom ratio for the “Minimal” set- ting, refer to “Storing the Desired Zoom Ratio” on page 3-38. In the Basic screen, touch [Zoom]. The Zoom screen appears. Touch [Minimal]. Touch [OK]. The Basic screen appears again. im7520/im6020 3-31...
Page 482: Selecting A Preset Zoom Ratio (Enlarge And Reduce Settings)
0 Touch [+] to enlarge the zoom ratio, and touch [–] to reduce the zoom ra- tio in ×0.001 increments. In the Basic screen, touch [Zoom]. The Zoom screen appears. Touch the button for the appropriate zoom ratio according to the orig- inal and paper sizes. Touch [OK]. The Basic screen appears again. 3-32 im7520/im6020...
Page 483: Typing In The Zoom Ratio (Zoom With Constant X And Y Ratio Setting)
0 The entered zoom ratio can be stored. For details on storing the zoom ra- tio, refer to “Storing the Desired Zoom Ratio” on page 3-38. In the Basic screen, touch [Zoom]. The Zoom screen appears. Touch [XY Zoom]. The Zoom screen appears. im7520/im6020 3-33...
Page 484 Touch the button under “Zoom with Constant X and Y Ratio”, and then use the keypad to type in the desired zoom ratio. – To cancel changes to the settings, touch [Cancel]. Touch [OK] twice. The Basic screen appears again. 3-34 im7520/im6020...
Page 485: Typing In Separate X And Y Zoom Ratios (Independent Zoom Settings)
Error” appears. Type in a value within the allowable range. If the value was incorrectly entered, press the [C] (clear) key to erase the value, and then specify the correct value. In the Basic screen, touch [Zoom]. The Zoom screen appears. im7520/im6020 3-35...
Page 486 (between ×0.250 and ×4.000) for the Y direction. – To cancel changes to the settings, touch [Cancel]. Touch [OK], and then touch [OK] in the next screen that appears. The Basic screen appears again. 3-36 im7520/im6020...
Page 487: Selecting A Stored Zoom Ratio
×0.250 and ×4.000). For details on storing zoom ratios, refer to “Storing the Desired Zoom Ratio” on page 3-38. In the Basic screen, touch [Zoom]. The Zoom screen appears. Touch the button for the desired zoom ratio under “Set Zoom”. Touch [OK]. The Basic screen appears again. im7520/im6020 3-37...
Page 488 0 To store a “Minimal” zoom ratio, type in the desired zoom ratio between ×0.900 and ×0.999. In the Basic screen, touch [Zoom]. The Zoom screen appears. Touch [XY Zoom]. The Zoom screen appears. 3-38 im7520/im6020...
Page 489 Touch the button or [Minimal] where the new zoom ratio is to be stored. – To cancel changes to the settings, touch [Cancel]. The specified zoom ratio is stored. Touch [OK], and then touch [OK] in the next two screens that appear. The Basic screen appears again. im7520/im6020 3-39...
Page 490: Selecting A Simplex/Duplex Setting (1-Side/2-Sides Settings)
The following four 1-Side/2-Sides settings are available. 1-Side/2-Sides Setting Description Select this setting to produce single-sided copies from single-sided original. Select this setting to produce one double-sided copy from two single-sided original. Select this setting to produce two single-sided copies from one double-sided original. 3-40 im7520/im6020...
Page 491 Basic Copy Operations 1-Side/2-Sides Setting Description Select this setting to produce double-sided copies from double-sided original. The following procedures describe how to select a 1-Side/2-Sides setting. im7520/im6020 3-41...
Page 492: To Select Single-Sided Copies
0 For details on using the original glass to scan multiple original pages, re- fer to “Scanning a Multi-Page Original from the Original Glass” on page 3-13. In the Basic screen, touch [Simplex/Duplex]. The Simplex/Duplex screen appears. Touch [1 1] or [2 Touch [OK]. The Basic screen appears again. 3-42 im7520/im6020...
Page 493: To Select Double-Sided Copies
For details on specifying the position of the binding margin for the paper to be printed on, refer to “Adding Filing Margins to Copies (“Page Margin” Function)” on page 8-54. In the Basic screen, touch [Simplex/Duplex]. The Simplex/Duplex screen appears. im7520/im6020 3-43...
Page 494 Basic Copy Operations Touch [1 2] or [2 Touch [OK]. The Basic screen appears again. 3-44 im7520/im6020...
Page 495: Selecting The Quality Of The Original
(such as that written with a pencil). The copied text is reproduced so that it is darker, providing text that is easy to read. Dot Matrix The following procedure describes how to select an Orig. Image Type set- ting. im7520/im6020 3-45...
Page 496: To Specify An Orig. Image Type Setting
For an original that contains both text and photos, touch [Text/Pho- to]. – For an original that contains faint text, touch [Dot Matrix]. The Original Image Type screen appears again. Detail To cancel a setting, touch the button for a setting different from the cur- rently selected setting. 3-46 im7520/im6020...
Page 497: Specifying The Density Settings
Each time [Light] or [Dark] is touched, the background density is lightened or darkened by one level. Touch [Std.] to select the middle setting of the nine levels. The following procedures describe how to specify the density settings. im7520/im6020 3-47...
Page 498: Adjusting The Print Density (Density Settings)
Each time [Light] or [Dark] is touched, the density is lightened or darkened by one level. – To select the middle of the nine levels, touch [Std.]. – Touch [Auto] to automatically adjust the level of the density accord- ing to the document being copied. Touch [OK]. 3-48 im7520/im6020...
Page 499: Adjusting The Background Density (Adjust Background Settings)
The Density screen appears. Select the desired background density setting. – Each time [Light] or [Dark] is touched, the density is lightened or darkened by one level. – To select the middle of the nine levels, touch [Std.]. Touch [OK]. im7520/im6020 3-49...
Page 500: Selecting A Combine Originals Setting
“×1.0”, Enlarge, Reduce, or XY Zoom (Zoom with Con- stant X and Y Ratio and Independent Zoom) settings. To use the settings together, set the “Auto Zoom for Combine/Booklet” parameter in Utility mode to “OFF”. For details, refer to “Copier Setting” on page 12-21. 3-50 im7520/im6020...
Page 501 <Vertical> 8 in 1 Select this setting to print eight original pages on one page. The page arrangement (Numbering Direction settings) can be specified. <Horizontal> <Vertical> The following procedure describes how to select a Combine Originals set- ting. im7520/im6020 3-51...
Page 502: Copying Multiple Original Pages Onto A Single Page (Combine Originals)
“Horizontal” can be viewed in the sub display area. – If “4 in 1” or “8 in 1” was selected, touch [Horizontal] or [Vertical] to specify the page arrangement. – To cancel the setting, touch the button again to deselect it. 3-52 im7520/im6020...
Page 503: Selecting Finishing Settings
“Selecting the Position of the Binding Margin (Margin Set- tings)” on page 3-22. The following Finishing Settings are available. Finishing Setting Description Sort Select this setting to separate each set of a multi-page original (collated).(Refer to page 3-56) im7520/im6020 3-53...
Page 504 The copies are fed out and stacked on top of each other with each set shifted to separate it.(Refer to page 3-53,p. 3-57) Face Up Select this setting to feed out copies with the front side facing up.(Refer to page 3-58) 3-54 im7520/im6020...
Page 505 3-59) Punch Select this setting to punch holes (2 or 3 holes) in the copies for filing them.(Refer to page 3-63) The following procedures describe how to select Finishing settings. im7520/im6020 3-55...
Page 506: Separating Copies By Sets ("Sort" Setting)
In the Basic screen, touch [Finishing]. The Finishing screen appears. Touch [Sort]. – To separate each set of copies, touch [Offset]. To cancel the set- ting, touch [Offset] again to deselect it. Touch [OK]. The Basic screen appears again. 3-56 im7520/im6020...
Page 507: Separating Copies By Pages ("Group" Setting)
In the Basic screen, touch [Finishing]. The Finishing screen appears. Touch [Group]. – To separate each set of pages, touch [Offset]. To cancel the “Off- set” setting, touch [Offset] again to deselect it. Touch [OK]. The Basic screen appears again. im7520/im6020 3-57...
Page 508: Feeding Out Copies Face Up ("Face Up" Setting)
– To cancel the setting, touch [Face Up] again to deselect it. – To cancel changes to the settings, touch [Cancel]. Touch [OK]. The Basic screen appears again. 3-58 im7520/im6020...
Page 509: Stapling Copies (Staple Settings)
Maximum Number of Sets Other than 11 × 2 to 9 sheets 100 sets 10 to 20 sheets 50 sets 21 to 30 sheets 30 sets 31 to 40 sheets 25 sets 41 to 50 sheets 20 sets im7520/im6020 3-59...
Page 510 2 to 9 sheets 50 sets 10 to 20 sheets 50 sets 21 to 30 sheets 30 sets 31 to 40 sheets 25 sets 41 to 50 sheets 20 sets 51 to 60 sheets — 61 to 100 sheets — 3-60 im7520/im6020...
Page 511: To Bind Copies With Staples
To cancel the Staple settings, touch [Corner] or [2 Position] again to deselect it. – To cancel changes to the settings, touch [Cancel]. Touch [Position], and then touch the button for the desired position. – To cancel changes to the settings, touch [Cancel]. im7520/im6020 3-61...
Page 512 11-11/16 in. or less, the long side of the paper is sta- pled. If the original length(X) is more than 11-11/16 in. , the short side of the paper is stapled. Touch [OK] twice. The Basic screen appears again. 3-62 im7520/im6020...
Page 513: Punching Holes In Copies (Punch Settings)
The procedure for selecting two punched holes is described below. When Finisher 9202/9204 and Punch Kit im9220010 are installed is installed Paper Weight Paper Size 13-1/4lb to 34lb 11 × 17w, 8-1/2 × 14w, 8-1/2 × 11w/v, 5-1/2 × 8-1/2w/v, Exectivew/v, Foolscap w im7520/im6020 3-63...
Page 514: To Punch Holes In Copies
To cancel the setting, touch [Offset] again to deselect it. – To cancel the Punch setting, touch [2-Hole] or [3-Hole] again to deselect it. – To cancel changes to the settings, touch [Cancel]. Touch [Position], and then touch the button for the desired position. 3-64 im7520/im6020...
Page 515 If the original length is more than 11-11/16 in. , the holes are punched along the short side of the paper. – To cancel changes to the punched hole position, touch [Cancel]. Touch [OK] twice. The Basic screen appears again. im7520/im6020 3-65...
Page 516: Specifying Folding Settings
Z-Fold Select this setting to fold copies at the center, and then 9202 fold them in half again before feeding them out. (Z- 9204 folding unit 9263 must be installed.) 3-66 im7520/im6020...
Page 517: To Fold Copies At The Center ("Half Fold")
“Half Fold” is selected. In the Basic screen, touch [Folding]. The Folding screen appears. Touch [Half Fold]. – To cancel changes to the settings, touch [Cancel]. – To cancel the “Half Fold” setting, touch the button for a different setting. im7520/im6020 3-67...
Page 518: To Bind Copies At The Center ("Fold & Staple")
Recommended zoom ratio when a Booklet setting is selected (×0.647) 0 When the “Fold & Staple” setting is selected, the “Group”, “Offset”, “Face Up”, Staple and Punch settings are not available. In the Basic screen, touch [Folding]. The Folding screen appears. 3-68 im7520/im6020...
Page 519: To Fold Copies Fanned ("Z-Fold")
* The number of sheets that can be bound together differs depending on the paper weight. 21-1/4lb paper: 20 sheets 28lb paper: 16 sheets To fold copies fanned (“Z-Fold”) 0 When the “Z-Fold” setting is selected, the “Group” and “Face Up” set- tings are not available. im7520/im6020 3-69...
Page 520: To Fold Copies In Three ("Tri-Fold")
1 sheet Number of Folded Sheets Maximum Number of Sets 1 sheet 30 sets To fold copies in three (“Tri-Fold”) 0 When the “Tri-Fold” setting is selected, the “Group”, “Offset”, “Face Up”, Staple and Punch settings are not available. 3-70 im7520/im6020...
Page 521 When finisher 9204 and Z-folding unit 9263 are installed Paper Weight Paper Size Number of Folded Sheets 16lb to 21-1/4lb 8-1/2 × 11w 3 sheets 21-1/4 to 28lb 1 sheet Number of Folded Sheets Maximum Number of Sets 1 sheet 50 sets im7520/im6020 3-71...
Page 522: Scanning The Next Original To Be Copied While A Copy Job Is Being Printed (Next Job Reservation)
[Stop] key. For details, refer to “Performing Operations on Jobs” on page 11-6. Press the [Start] key to begin scanning and outputting the current copy job. The Basic screen for reserving a copy job appears. 3-72 im7520/im6020...
Page 523 Press the [Start] key. After the current copy job is finished, the next copy job begins. – When the current copy job is finished, the copy settings for the next copy job are automatically displayed and the copy operation be- gins. im7520/im6020 3-73...
Page 524: Stopping Scanning/Printing
3-75. Press the [Stop] key while a document is be- Stop ing scanned or a job is Start being printed. Scanning/printing stops. The Stopped Jobs screen appears. To resume all stopped jobs, press the [Start] key. 3-74 im7520/im6020...
Page 525: Deleting A Stopped Job
Press the [Stop] key while an original is being Stop scanned or a job is being Start printed. Scanning/printing stops. The Stopped Jobs screen appears. Select the job to be deleted, and then touch [Delete]. The selected job is deleted. im7520/im6020 3-75...

This manual is also suitable for:

Im6020

imagistics im7520 User Manual

14 Index

Managing Jobs

Table of Contents

Available Features

Explanation of Manual Conventions

1 Installation and Operation Precautions

2 Before Making Copies

3 Basic Copy Operations

Quick Links

Chapters

Troubleshooting

Related Manuals for imagistics im7520

Summary of Contents for imagistics im7520