L.B. White TS080 Owner's Manual And Instructions

L.B. White TS080 Owner's Manual And Instructions

Premier tent heaters

Advertisement

Owner's Manual and Instructions
Congratulations!
Your new L.B. White heater incorporates the benefits from the most experienced
manufacturer of heating products using state-of-the-art technology.
We, at L.B. White,
welcome any suggestions or comments you may have...call us, toll-free,
at 1-800-345-7200.
ATTENTION ALL USERS
This heater has been tested and evaluated by C.S.A. International in accordance with
the requirements of Standard ANSI Z83.7 CSA 2.14 and is listed and approved as a
ductable direct gas-fired forced-air construction heater with application for the
temporary heating of buildings under construction, alteration, or repair. Additionally,
this heater has been application reviewed and approved by C.S.A. International for
USA Tent Heating Applications with temporary human occupancy. If you are
considering using this product for any application other than its intended use, then
please contact your fuel gas supplier, or the L.B. White Co., Inc.
Premier Tent Heaters
MODELS
OUTPUT (Btuh)
TS080
80,000
TS170
170,000
Certification by:
for your confidence in our products and
FUEL
Propane Vapor
Withdrawal
or
Natural Gas
150-26421

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TS080 and is the answer not in the manual?

Questions and answers

Summary of Contents for L.B. White TS080

  • Page 1 170,000 Natural Gas Certification by: Congratulations! Your new L.B. White heater incorporates the benefits from the most experienced manufacturer of heating products using state-of-the-art technology. We, at L.B. White, for your confidence in our products and welcome any suggestions or comments you may have...call us, toll-free, at 1-800-345-7200.
  • Page 2 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■...
  • Page 3: Table Of Contents

    Electrical Connection and Ladder Diagram, TS080........
  • Page 4: Heater Specifications

    Heater Specifications Model SPECIFICATIONS TS080 TS170 Propane Natural Propane Natural Fuel Type Maximum Input (BTUH) 80,000 170,000 Ventilation Air Required 450 CFM 1,200 CFM to Support Combustion 10 in W.C. 4 in. W.C. 10 in. W.C. 4 in. W.C. Burner Manifold Pressure nlet Gas Supply MAX.
  • Page 5: Safety Precautions

    Safety Precautions WARNING Asphyxiation Hazard ■ ■ Do not use this heater for heating human living Refer to the specification section of the heater’s quarters. Owner’s Manual, heater dataplate, or contact the L.B. White Company to determine combustion air ventilation ■...
  • Page 6 Commonwealth of Massachusetts. heater is not going to be used in the heating of the tent. 2. All installations and applications of L.B. White heaters must meet all relevant local, state and national 12. This heater is equipped with a three-prong codes.
  • Page 7: Installation Instructions

    DO NOT USE ANY OTHER DUCTWORK, DUCTING,FIELD FABRICATED DUCTS, TARPS,STOVE PIPE, or any other 1. Read all safety precautions and follow L.B. White means of making the connection between the heater and recommendations when installing this heater. If the inside of the tent.
  • Page 8: Propane Gas Supply Sizing

    -- Stand clear while the main burner ignites to propane gas liquid withdrawal system or application. prevent injury caused from hidden leaks that If you are in doubt, contact the L.B. White Co., Inc. could cause flashback. -- With the main burner in operation, check all 14.
  • Page 9: Sliding Handle Assembly (Premier 170)

    SLIDING HANDLE ASSEMBLY Premier 170 The Premier 170 is equipped with sliding handles for FIG. 1 convenient “wheel-barrow” style mobility. EXTEND HANDLE UNTIL IT SNAPS INTO -- Depress the snap-button on the underside of the RETAINING HOLE sliding handle storage bracket. -- Fully extend both handles until the snap button locks HANDLE BRACKET into place.
  • Page 10: Wheel, Leg & Lifting Handle Assembly Premier 170

    WHEEL, LEG & LIFTING HANDLE ASSEMBLY Premier 170 See Fig. 4 for assembly of components. Ensure all hardware is tightened securely. FIG. 4 REMOVE CASE SCREW AT EACH END OF HEATER (BOTH SIDES) BEFORE INSTALLING U-HANDLES. HANDLE - U, WITH 8" LEGS WASHER 5/16 (QUANTITY 8) BOLTS 5/16-18 X 1"...
  • Page 11: Hose And Regulator Assembly

    HOSE AND REGULATOR ASSEMBLY 1. Connect rigid end of hose to regulator outlet. Connect 2. The hose may be coiled up and hung on the hose other end to hose adapter at heater. Tighten securely. hanger as shown in Fig. 7. See Fig 6.
  • Page 12: Duct Kit Assembly

    DUCT KIT ASSEMBLY Accessory 26346 1. Extend duct kit to 12 ft. length. FIG. 9 2. See Fig. 9 for installation of duct. Hand tighten the screws snugly. (Note: Slots are also provided at the sides of heater’s air discharge to accomodate earlier style duct adapters with tab mounting configuration.) FASTEN WING SCREWS 3.
  • Page 13: End Diffuser Assembly

    INTO SLOT BEFORE TIGHTENING WING SCREWS INTO CAGE NUTS. CONNECTING REGULATOR TO GAS SUPPLY TS170G-07 ■ FIG. 13 Only use the L.B. White regulator supplied with the heater. ■ The heater must be regulated at all times for proper operation. ■...
  • Page 14: Start-Up Instructions

    Start-Up Instructions Connect the electrical cord to an approved electrical FIG. 15 outlet. STATUS A selector switch located on the back of the heater GAS VALVE allows heater operation in either HEAT or VENT (no heat) modes. See Fig. 15. AIR PROVING A.
  • Page 15: Shut-Down Instructions

    L.B. White Co., Inc. Dataplates, start- up and shut-down instructions and warnings are Regulators can wear out and function improperly.
  • Page 16: General

    GENERAL The high limit switches, HEAT/VENT switch, and WARNING thermostat can be tested by disconnecting the leads Burn Hazard at the component, and jumpering the leads together: ■ Heater surfaces are hot for a period of time after the heater has been shut down. Reconnect the electrical supply and open fuel ■...
  • Page 17: Air Proving Switch

    AIR PROVING SWITCH 1. Open louvered case access panel. FIG. 17 NUTS Remove two sheet metal screws holding air proving PADDLE switch blower housing. Remove assembly by turning switch assembly 90 degrees so the switch paddle can be pulled through oblong hole on side of fan housing.
  • Page 18: Testing The Manual Reset High Limit Switches

    For Premier 170 heaters, the bolt is accesible through an opening in the heater’s support leg. Use a ratchet with extension and 9/16 SPACER in. socket. See Fig. 22. For model TS080, also remove the spacer between heater base and burner. See Fig. 23.
  • Page 19 4. Pivot the gas control assembly to expose the burner orifice. See Fig. 24. Replace components as needed. Premier 80 FIG. 24 ORIFICE HOLDER ORIFICE GAS CONTROL 8° CONTROL VALVE Premier 170 5. When assembling the control valve to manifold, the CONTROL valve must be offset 8 degrees from the orifice holder ORIFICE...
  • Page 20: Gas Pressure Checks

    Gas Pressure Checks 2. Securely connect a pressure gauge to each pressure WARNING tap. ■ Do not disassemble the gas control valve. 3. Open the fuel supply valves to the heater and ■ Do not attempt to replace any components of the gas reconnect the heater electrical supply.
  • Page 21: Troubleshooting Information

    Troubleshooting Information READ THIS ENTIRE SECTION BEFORE BEGINNING Ventilation Mode Problem Page Motor Does Not Run ......26 TO TROUBLESHOOT PROBLEMS.
  • Page 27: Electrical Connection And Ladder Diagram, Ts080

    Electrical Connection and Ladder Diagram PREMIER 80 CAUTION - REFER TO THE HEATER'S ELECTRICAL CONNECTION DIAGRAM WHEN SERVICING TO AVOID WIRING ERRORS & HEATER MALFUNCTION. CHECK FOR PROPER OPERATION AFTER SERVICING. WARNING: THIS HEATER MAY START AT ANY TIME BLACK WHITE DIRECT SPARK MOTOR...
  • Page 28: Electrical Connection And Ladder Diagram, Ts170

    Electrical Connection and Ladder Diagram PREMIER 170 CAUTION - REFER TO THE HEATER'S ELECTRICAL CONNECTION DIAGRAM WHEN SERVICING TO AVOID WIRING ERRORS & HEATER MALFUNCTION. CHECK FOR PROPER OPERATION AFTER SERVICING. WARNING: THIS HEATER MAY START AT ANY TIME BLACK WHITE DIRECT SPARK MOTOR...
  • Page 29: Heater Component Function

    Heater Component Function Air Proving Switch High Limit Switch Safety device used to insure that the proper air flow is being Safety device wired into the control system which is used to achieved before the gas valve is opened. break an electrical circuit to the gas control valve in event of overheat situation.
  • Page 30: Parts Identification Parts Schematic And Parts List Premier 80

    Parts Identification PREMIER 80 PARTS SCHEMATIC...
  • Page 31: Premier 80

    PREMIER 80 PARTS LIST Item Description Part Number Regulator Propane Gas 26377 Natural Gas 21999 Handwheel with Spring Propane Gas 26395 Universal Hose Kit, 15 ft. Hose w/ Adapters 24600 Adapter 1/2 NPT x 5/8 - 18 06655 09309 Screw 09425 Valve, Gas Control Propane Gas...
  • Page 32 PREMIER 170 PART SCHEMATIC...
  • Page 33: Premier 170

    PREMIER 170 PARTS LIST Item Description Part Number Regulator Propane Gas 26419 Natural Gas 09795 Hand Wheel with Spring Propane Gas 26395 Universal Hose Kit, 15 ft. Hose w/ Adapters 24600 Wheel Kit 26418 Axle 26415 Cotter Pin 26417 Kit, Leg Bracket 26413 Bolt and Washer 25866...
  • Page 34: Warranty Policy

    12 months from date of shipment from L B. White. found to be defective, L.B. White Co., Inc. will at its option, repair or replace the defective part or heater, with a new part or heater, F.O.B., Onalaska, Wisconsin.

This manual is also suitable for:

Ts170

Table of Contents