1. Manuals
  2. Brands
  3. Axis Manuals
  4. Network Storage Server
  5. StorPoint NAS 100
  6. User manual

Axis NAS 100 User Manual

Network hard disk server
Hide thumbs Also See for NAS 100:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
AXIS StorPoint NAS 100 User's Manual
StorPoint NAS 100
Network Hard Disk Server
U s e r ' s M a n u a l v e r 1 . 1

Advertisement

Table of Contents
loading

Related Manuals for Axis NAS 100

Summary of Contents for Axis NAS 100

  • Page 1 AXIS StorPoint NAS 100 User’s Manual StorPoint NAS 100 Network Hard Disk Server U s e r ’ s M a n u a l v e r 1 . 1...

  • Page 2: Safety Notices

    Please observe all safety markings and instructions when using this detect any inaccuraries or omissions, please inform us at an address product. which can be found in the last appendix of the manual. Axis Communications cannot be held responsible for any technical or Caution! - potential hazard that can damage the product.
  • Page 3 StorPoint NAS. To fully benefit from the manual, you should be familiar with basic networking principles. This manual applies to AXIS StorPoint NAS 100 Wide SCSI and AXIS StorPoint NAS 100 IDE with software release 1.10 and subsequent releases until otherwise notified.
  • Page 4 If you are connected to Internet, you can find online WWW: http://www.axis.com FTP server: ftp://ftp.axis.com/pub/axis manuals, technical support, firmware updates, application software, company information, on any of Support tech-sup@axis.com e-mail address: the addresses listed to the left. AXIS StorPoint NAS 100 User’s Manual...

  • Page 5: Table Of Contents

    AXIS StorPoint NAS 100 ........7...
  • Page 6 Index ........... . . 105 AXIS StorPoint NAS 100 User’s Manual...

  • Page 7: Section 1 Introduction

    StorPoint NAS supports disk mirroring (RAID-1) which means that data written to a hard disk can be automatically and simultaneously written to a second hard disk. Throughout this manual, AXIS StorPoint NAS 100 is referred to as simply Note: StorPoint NAS.

  • Page 8: Features And Benefits

    Netscape Navigator or Microsoft Internet Explorer. The support includes configuration, management and disk access. Speed By using a 32-bit RISC processor and cache memory expandable up to 160 MB, data throughput of up to 16 Mbit/sec on a single client. AXIS StorPoint NAS 100 User’s Manual...

  • Page 9: Axis Storage Online Cd

    AXIS Storage Online CD includes user documentation and other online information, product firmware, software utilities, data sheets etc. for all the AXIS StorPoint Server products. You can use the CD within all of the supported Axis computing environments. The CD will autostart from a local CD drive on Windows 95/98/2000 and NT platforms.

  • Page 10: Basic Installation

    • Refer to “Installing StorPoint NAS in a Tower” on page 97 on how to install StorPoint NAS in a 5 " tower. • Refer to “Connecting the Hard Disks to StorPoint NAS” on page 98 on how to connect hard disks to StorPoint NAS. AXIS StorPoint NAS 100 User’s Manual...

  • Page 11: Connecting The Storpoint Nas To The Network

    The StorPoint NAS front panel indicators will flash during power-on and self- test. When the Status indicator stops flashing and turns solid green, your StorPoint NAS is ready for use. Network hub Network cables StorPoint NAS nstalled in a tower with hard disk drives AXIS StorPoint NAS 100 User’s Manual...

  • Page 12: Assigning An Ip Address

    Try accessing your StorPoint NAS via a standard Web browser. Use the default Automatic IP Setting (DHCP) server name AXIS<nnnnnn> where <nnnnnn> are the last six digits of the serial number. Example The serial number of your StorPoint NAS is 00408C3E5207. Enter AXIS3E5207 in the address/location field: •...
  • Page 13 StorPoint NAS will no longer accept a new IP address using the Web browser or ARP method. You will find the ProtectIP parameter under the [IP] section in the file located in the config.ini folder. Use a text editor to edit the file. System/ServerProperties AXIS StorPoint NAS 100 User’s Manual...
  • Page 14 This method will work for most Windows configurations. However, if you experience problems when using this method, we recommend that you use the AXIS IP Installer for setting the IP address. See “AXIS IP Installer” on page 15. AXIS StorPoint NAS 100 User’s Manual...
  • Page 15 Section 2: Basic Installation AXIS IP Installer AXIS IP Installer is an application that allows you to assign IP addresses to your StorPoint NAS, find IP addresses of already installed StorPoint Servers and access the StorPoint NAS Web interface. The required utility software is available on the AXIS Storage Online CD. It can also be downloaded from the Axis Web site at http://www.axis.com...
  • Page 16 If you are using host names, you can map a unique host name to the acquired IP address. Refer to your system manuals or to the Network Administrator for instructions on how to perform the name mapping on your particular system. AXIS StorPoint NAS 100 User’s Manual...
  • Page 17 Some BSD-type arp -s systems expect the IP address and Ethernet address in reverse order, whereas IBM AIX systems require the additional argument . For example: ether arp -s ether <IP address> 00:40:8C:3E:52:07 temp AXIS StorPoint NAS 100 User’s Manual...
  • Page 18 DHCP scope. However, we recommend that you specify the SLP settings in the StorPoint NAS parameter list instead. You can do this via the StorPoint NAS Web interface or by editing the file. config.ini AXIS StorPoint NAS 100 User’s Manual...
  • Page 19 3. Start the BOOTP daemon (if not already running), typically by the command: bootpd -a 4. Restart StorPoint NAS to download the IP address, default router address and subnet mask. AXIS StorPoint NAS 100 User’s Manual...
  • Page 20 3. If it is not already running, start the RARP daemon. This is typically done using the command rarpd -a. 4. Restart StorPoint NAS to download the IP address. AXIS StorPoint NAS 100 User’s Manual...

  • Page 21: Basic System Settings

    The StorPoint NAS Home Page is displayed. admin button From this page, users can display and access the volumes according to the access permissions set up by the Administrator. 3. Click admin to access the Administration pages. AXIS StorPoint NAS 100 User’s Manual...
  • Page 22 • Event Log - Viewing the event log that contains occurrences in your StorPoint NAS. • Statistics - Displaying statistics on your StorPoint NAS. • Support - Trouble shooting, server report, software version, Axis online services, contact information etc. • Help Contents - Displaying general help information.
  • Page 23 Shut Down You will find the parameter under the section. Shut Down [Server] 3. Save the file. config.ini Your StorPoint NAS will shut down and you can now turn off the power. AXIS StorPoint NAS 100 User’s Manual...
  • Page 24 3. Specify and confirm the Server password. 4. Click Close. If you lose the Server password, you must restore the factory default settings Note: using the Push button. See “Restoring Factory Default Settings” on page 78. AXIS StorPoint NAS 100 User’s Manual...
  • Page 25 * Note: NTP is not natively supported by Windows NT servers. You will need third party software. To set the time manually, choose Manually and specify the date in format, and time in format using the 24 hour clock. yy-mm-dd hh:mm:ss 5. Click Close. AXIS StorPoint NAS 100 User’s Manual...
  • Page 26 6. Select the TCP/IP tab and verify the settings. 7. Click OK. Context sensitive online help is available for all parameters. Notes: The parameter list is described in detail in “Appendix A - Parameter List” . AXIS StorPoint NAS 100 User’s Manual...

  • Page 27: Microsoft & Ibm Networks (Smb)

    SMB server name. You can use the StorPoint NAS Administration Web pages for configuration. The default SMB server name is AXIS<nnnnnn>, where <nnnnnn> are the last SMB Server Name six digits of the StorPoint NAS serial number. This is the name that will be presented to the Windows clients on the network.
  • Page 28 5. Choose Windows (SMB). Click Start to proceed with the installation. 6. Follow the instructions on the screen. When finished, click Close. 7. Click Detailed View . The Protocols dialog box appears. 8. Select the Windows (SMB) tab and verify the settings. AXIS StorPoint NAS 100 User’s Manual...

  • Page 29: Access Control

    3. Click Network Settings. 4. Click Detailed View . The Protocols dialog box appears. 5. Select the Windows (SMB) tab . If you want to change the Security Mode parameter, click Change... 6. Click OK. AXIS StorPoint NAS 100 User’s Manual...
  • Page 30 5. Open the Windows Sharing page. 6. Select the Share as radio button, and enter a share name in the Share Name field. 7. Enter a comment in the Comment field. 8. Click OK. AXIS StorPoint NAS 100 User’s Manual...
  • Page 31 The access rights are additive which means that the user's access rights are the summary of the rights granted from individual assignments and group memberships. Files and subfolders created within the selected folder will automatically inherit the same access rights. AXIS StorPoint NAS 100 User’s Manual...
  • Page 32 The access rights are additive which means that the user's access rights are the summary of the rights granted from individual assignments and group memberships. Files and subfolders created within this folder will automatically inherit the same access rights. 7. Click OK. AXIS StorPoint NAS 100 User’s Manual...
  • Page 33 The default setting is Full access with no password which means that all Note: users have full access. 8. Click OK. AXIS StorPoint NAS 100 User’s Manual...

  • Page 34: Netware (Ncp)

    If your network supports TCP/IP, you can use the StorPoint NAS Administration Web pages for configuration. The default NetWare server name is AXIS<nnnnnn>_NW, where <nnnnnn> NetWare Server are the last six digits of the StorPoint NAS serial number. This is the name that Name will be presented to the NetWare clients on the network.
  • Page 35 3. Click admin. You will be prompted for the user name and password. By default, these are set to . To change the Server password, see root pass “Server Password” on page 24. 4. Click Network Settings. AXIS StorPoint NAS 100 User’s Manual...
  • Page 36 3. Use a standard text editor such as Notepad to edit the configuration parameters. From Windows Explorer or File Manager, locate the StorPoint NAS configuration file, which is located in the config.ini folder. System/ServerProperties AXIS StorPoint NAS 100 User’s Manual...
  • Page 37 TimeSyncSource = NDS [NetWare] NDSEnable = yes IPXEnable = yes PureIPEnable = no NDSTreeName = ACMECORP NDSServerContext = Corp.Acme NDSAdminName = Admin.Acme NDSAdminPassword = secret NDSInstall = install NDSRightsStorage = NDS TimeSyncSources = SAP AXIS StorPoint NAS 100 User’s Manual...
  • Page 38 5 minutes before deleting the object. If you do not turn off the server before attempting to delete the server object, your client workstation will hang and you will have to reboot your PC. However, when using NDS manager this is not needed. AXIS StorPoint NAS 100 User’s Manual...

  • Page 39: Authentication Server

    If used as a bindery server, no specific installation is required prior to using and Installation as a Bindery Server accessing your StorPoint NAS. However, it is recommended that you specify the authentication server. AXIS StorPoint NAS 100 User’s Manual...

  • Page 40: Access Control

    NetWare NDS To make all the volumes available to some users only, follow these steps: 1. Login as Admin, and start the NWAdmin. 2. Remove the [Public] trustee from the root of the SYS volume. AXIS StorPoint NAS 100 User’s Manual...
  • Page 41 StorPoint NAS. If the user is defined in the file server that StorPoint NAS uses for authentication, the user will automatically have access to StorPoint NAS. AXIS StorPoint NAS 100 User’s Manual...
  • Page 42 StorPoint NAS, the client must have an active connection. 2. Login as Supervisor on your NetWare Bindery file server and start Filer. 3. Change the current directory to AXIS<nnnnnn>_NW/SYS:. 4. Remove the [EVERYONE] trustee from the root. 5. Add a new trustee assignment to the root.

  • Page 43: Unix (Nfs)

    “Server Password” on page 24. 3. Click Network Settings. 4. Click Detailed View . The Protocols dialog box appears. 5. Select the UNIX (NFS) tab and specify the settings. 6. Click OK. AXIS StorPoint NAS 100 User’s Manual...

  • Page 44: Access Control

    * which represents any number of characters, except dots (...). A single * implies any host name. which represents one character, except dot (.). Simply * implies any host name. However, * and ? cannot represent a dot (.) when used within names. AXIS StorPoint NAS 100 User’s Manual...

  • Page 45: Mounting Your Storpoint Nas

    -e <IP address> 3. Mount the resource. mount <IP address>:<resource> <directory> where is the IP address or host name <IP address> Example 1 (Root): mount 192.16.253.80:/ /storpoint_sales_dept Example 2 (Volumes directory): mount 192.16.253.80:/volumes /storpoint_sales_dept AXIS StorPoint NAS 100 User’s Manual...
  • Page 46 To increase performance, you can set the buffer size to 8192 as an option in the mount command on most UNIX systems, e.g. mount -o rsize=8192 <IP address>:<resource> <mountpoint> Different UNIX systems may have different mount command options. Refer to the manual page on the client system. AXIS StorPoint NAS 100 User’s Manual...

  • Page 47: Section 6 Ftp

    • “Section 3 - Microsoft & IBM Networks (SMB)” • “Section 4 - NetWare (NCP)” • “Section 5 - UNIX (NFS)” • “Section 7 - Web Browser (HTTP)” AXIS StorPoint NAS 100 User’s Manual...

  • Page 48: Network Settings

    • FTP Max Users, which specifies the maximum number of simultaneous FTP sessions. 7. Click OK. Notes: Context sensitive online help is available for all parameters. The parameter list is described in detail in “Appendix A - Parameter List” . AXIS StorPoint NAS 100 User’s Manual...

  • Page 49: Access Control

    Volumes folder, but no access to the System folder. A user logging in with the FTP user name and password will automatically Warning! get access to the Volumes folder, i.e. all the hard disks and their contents. No access restrictions will apply. AXIS StorPoint NAS 100 User’s Manual...

  • Page 50: Web Browser (Http)

    6. Select the Web (HTTP) tab and verify the settings. 7. Click OK. Notes: Context sensitive online help is available for all parameters. The parameter list is described in detail in “Parameter List” on page 65. AXIS StorPoint NAS 100 User’s Manual...

  • Page 51: Access Control

    File Properties To restrict user access to a particular resource: 1. Click File Properties. 2. Locate the resource you want to protect in the file tree. 3. Click Properties . The Access Rights dialog appears. AXIS StorPoint NAS 100 User’s Manual...
  • Page 52 Administration pages only, follow these steps: 1. Click Network Settings. 2. Click Detailed View 3. Select the Web (HTTP) tab. 4. Uncheck the Enable access to volumes via Web browser (HTTP) check box. 5. Click OK. AXIS StorPoint NAS 100 User’s Manual...

  • Page 53: Section 8 Managing The Hard Disks

    • Low Level Format - Use this format if you want to erase all data on a hard disk completely. This may take several hours depending on the hard disk size. 8. Click Start. AXIS StorPoint NAS 100 User’s Manual...

  • Page 54: Disk Mirroring (Raid-1)

    During this process the SCSI LED is alternating between green and amber. While creating identical images, the hard disks can be accessed for both reading and writing. Existing RAID-1 pairs are not effected when new disks are added. Note: AXIS StorPoint NAS 100 User’s Manual...
  • Page 55 In case of read errors, both disks will continue being used. The read error will be logged in the event log and a warning will be sent from the StorPoint NAS to the administrator via e-mail. Read and write errors will be listed on the Statistics page. AXIS StorPoint NAS 100 User’s Manual...

  • Page 56: Error Checking

    7. Click Start to start the error check. If you do not check the Automatically fix file system errors checkbox, only Note: a hard disk check will be performed. The results will be written to the Event Log. AXIS StorPoint NAS 100 User’s Manual...

  • Page 57: Monitoring Storpoint Nas

    Tools See ... Event log page 58 Statistics page 59 E-mail page 60 SNMP page 61 AXIS ThinWizard - page 62 a tool for locating and managing all the AXIS servers on your network AXIS StorPoint NAS 100 User’s Manual...

  • Page 58: Event Log

    When the server is restarted, a sub-set of critical events will remain in the event log. Click Clear Event Log, to clear the event log of events. AXIS StorPoint NAS 100 User’s Manual...

  • Page 59: Statistics

    Available space on the attached hard disks • List of users who are currently connected to your StorPoint NAS in each particular network environment • List of hard disks and the number of files and folders on these. AXIS StorPoint NAS 100 User’s Manual...

  • Page 60: E-Mail (Smtp)

    6. Enter the administrator’s e-mail address. 7. Select the required log events from the Mail Log Events drop down list. The selected log events will be sent to the e-mail address specified above. Click OK. AXIS StorPoint NAS 100 User’s Manual...

  • Page 61: Snmp

    . To change the Server password, see root pass “Server Password” on page 24. 3. Click Network Settings. 4. Click Detailed View 5. Select the SNMP tab. 6. Specify the settings, and click OK. AXIS StorPoint NAS 100 User’s Manual...

  • Page 62: Axis Thinwizard

    ThinWizard 1. Make sure an AXIS ThinWizard server is running on your network. 2. Start the Web browser and enter the name or IP address of the AXIS ThinWizard server in the location/address field. If the AXIS ThinWizard server is installed on a port other than port number 80, you must add the port number to the URL: http://<IP address>:<port number>/...
  • Page 63 3. The Create Network Group page opens. Type a name for the new network group. 4. Specify the IP address ranges and AXIS server types to be included in the network group. If you are only interested in storage servers, deselect all options but the Storage Servers option.
  • Page 64 2. Select the network group that includes your StorPoint NAS from the pull- down list. 3. All the detected AXIS servers included in the network group are listed. 4. Click the IP Address link of your StorPoint NAS. The StorPoint NAS Home Page, the File View page, appears.

  • Page 65: Appendix A Parameter List

    Enables BOOTP IP address setup. BOOTPEnable = yes DHCPEnable = yes Enables DHCP IP address setup. RARPEnable = yes Enables RARP IP address setup. DomainName Name of the domain to which StorPoint NAS belongs. AXIS StorPoint NAS 100 User’s Manual...
  • Page 66 SMBEnable = yes The server name in the SMB environment. Default is ServerName AXIS<nnnnnn> where nnnnnn are the last six digits of the serial number. Name of the StorPoint NAS workgroup in SMB. If not Domain/GroupName specified, the StorPoint NAS will appear in the folder that comes first in alphabetical order.
  • Page 67 The IP address of the DSS server. NetWareIP_DSS_Server NetWare server name to be presented to the NetWare ServerName = AXIS<nnnnnn>_NW clients. Default is AXIS<nnnnnn>_NW where nnnnnn are the last six digits of the serial number. Internal network address. Default is nn-nn-nn-nn where InternalNetAddress = nn-nn-nn-nn nnnnnnnn are the last eight digits of the serial number.
  • Page 68 Error means that only errors will be sent to the administrator. Warning means that only warnings will be sent to the administrator. All means that all logged events will be sent via e-mail to the administrator [END] AXIS StorPoint NAS 100 User’s Manual...
  • Page 69 DST is not included. Aust_Sydney The parameter values shown to the right include New_Zealand adjustments for DST. Afghanistan 4h30m Armenia_Azer Burma 6h30m China_PRC India 5h30m Iran 3h30m Iraq Jordan Kazak_Kirgi Lebanon Syria AXIS StorPoint NAS 100 User’s Manual...

  • Page 70: Directory Structure

    Flash - When updating the firmware, you can copy the file with the latest firmware version into this subfolder. • ServerProperties - Includes the configuration parameter list, event log and statistics files. • VolumeProperties - Includes one text file for each available volume. AXIS StorPoint NAS 100 User’s Manual...

  • Page 71: Editing The Configuration Parameters

    3. Windows 95 only: Change directory not to overwrite any of your system files. See the caution note below. 4. To access the configuration file, type: get config.ini AXIS StorPoint NAS 100 User’s Manual...
  • Page 72 Restart Do not restart your StorPoint NAS in the middle of the NDS installation. Important! The StorPoint NAS configuration settings are stored in the file Configuration Settings config.ini located in the folder. System/ServerProperties AXIS StorPoint NAS 100 User’s Manual...
  • Page 73 Appendix A: Parameter List Example: ; AXIS StorPoint NAS Parameter List, V1.10 [Server] HardwareAddress = 00:40:cc:24:c3:0c Date = 00-05-10 Time = 08:54:37 FactoryDefaults = no Restart = no TimeZone = UTC TimeSyncSource = None ServerPassword = ******** Shut Down = no...
  • Page 74 Full Access Password = [END] When editing the file, be sure that the equal sign and the parameter values Notes: are separated by a space. Do not remove the marker from the file. [END] AXIS StorPoint NAS 100 User’s Manual...

  • Page 75: Appendix B Troubleshooting

    Server Report which includes technical information about your product that will help the support personnel diagnose your problem. To receive update information about Axis products, services and software updates by e-mail, you can subscribe to the AxisNews mailing list at http://www.axis.com/services/axisnews.htm...

  • Page 76: The Front Panel Indicators

    GREEN * 100 Mbit packet arrived. GREEN * 10 Mbit packet arrived. AMBER * Flash loading in progress. AMBER * Mirroring a RAID-1 pair. AMBER / GREEN * Flashing, short interval. ** Flashing, long interval. AXIS StorPoint NAS 100 User’s Manual...

  • Page 77: Error Conditions

    * Flashing, short interval. ** Flashing, long interval. Status Indicator Red If the Status indicator turns red, this indicates a serious error in the hardware. If this happens, contact your dealer and return the unit for replacement. AXIS StorPoint NAS 100 User’s Manual...

  • Page 78: Restoring Factory Default Settings

    If you select the Configurations or All option, you will need to re-assign the Note: IP address as described in “Assigning an IP Address ” on page 12. 7. Click OK. The factory default setting will now be restored and your StorPoint NAS will then automatically restart. AXIS StorPoint NAS 100 User’s Manual...
  • Page 79 6. Press and hold the Push button again until the Status indicator shows a steady yellow light. This may take 10 - 15 seconds. Push button 7. Restart your StorPoint NAS. StorPoint NAS is now reset to factory default settings. AXIS StorPoint NAS 100 User’s Manual...

  • Page 80: Running A Diagnostic Test

    To perform the diagnostic test, follow these steps: Procedure 1. Start the Web browser, and enter the URL of the Diagnostics page in the location/address field: http://<IP address>/this_server/diag.shtml Example http://192.16.253.80/this_server/diag.shtml 2. The Diagnostics page appears: AXIS StorPoint NAS 100 User’s Manual...

  • Page 81: Errors When Accessing Storpoint Nas Or A Hard Disk

    If you have changed any of the following parameters after installing StorPoint NAS in the NDS tree, you might need to repeat the installation in order to connect to StorPoint NAS: • IP address • Internal Net Address • IPX Enable • PureIP Enable AXIS StorPoint NAS 100 User’s Manual...

  • Page 82: Difficulties Locating The Storpoint Nas In Netware

    PureIP environment, you cannot use SAP for automatic time synchronization. You can specify the name or IP address of the time server. You find the time source setting on the Network Settings | Detailed View | NetWare page. AXIS StorPoint NAS 100 User’s Manual...

  • Page 83: Insufficient Access Rights In Netware Nds

    6. Add the StorPoint NAS server object as a trustee with Read, Write, Create, Erase, Modify and File Scan rights to the directory where you want to store the access rights. StorPoint NAS will create the file once you start adding trustees. AXIS StorPoint NAS 100 User’s Manual...

  • Page 84: Name Resolution Problems In Windows (Smb)

    MAC address of StorPoint NAS to a reserved IP address. It is often recommended that you use these types of settings for server equipment. Refer to your Windows NT server manuals for more information on this. AXIS StorPoint NAS 100 User’s Manual...

  • Page 85: Problems Locating The Domain Controller In Windows (Smb)

    In Windows 95, you cannot tell the SMB client to change domain and user when you are already logged in. Therefore, you cannot use the local administrator account to solve domain problems in the Windows 95 environment. AXIS StorPoint NAS 100 User’s Manual...

  • Page 86: Appendix C Upgrading Storpoint Nas

    Appendix C: Upgrading StorPoint NAS Appendix C Upgrading StorPoint NAS This section includes the following information: Task See ... Obtaining new software page 87 Upgrading the firmware page 88 Extending the RAM memory page 91 AXIS StorPoint NAS 100 User’s Manual...

  • Page 87: Obtaining New Software

    You may wish to check the Axis Web Site at http://www.axis.com/, where you Over the Internet can download the latest versions of the software. A link to the Axis Web Site is available from the StorPoint NAS’ Home Page. You can also get files and information through anonymous ftp: log in to Anonymous FTP ftp.axis.com and go to the /pub/axis directory.

  • Page 88: Upgrading The Firmware

    Follow these steps to upgrade your StorPoint NAS by using drag-and-drop: 1. Download the latest software from the Axis Web site to your computer. 2. You can download the latest versions of the AXIS StorPoint CD E100 required software from the Axis Communications Web site. All software updates are free of charge.
  • Page 89 For more information about AXIS ThinWizard, refer to “Event Log ” on page Follow these steps to upgrade StorPoint NAS using AXIS ThinWizard: 1. Start the Web browser and enter the name or IP address of the AXIS ThinWizard server in the location/address field.
  • Page 90 6. Log out using the command depending on your FTP quit exit version. StorPoint NAS will automatically restart when the upgrade is complete. It is Caution! very important that you do NOT press the Power button during the upgrade. AXIS StorPoint NAS 100 User’s Manual...

  • Page 91: Extending The Ram Memory

    4k refresh cycles • A0-A11 address inputs Use one of these modules or equivalent: Manufacturer Type Centon P/N CKF115TE4VD391G Samsung P/N KMM466F804BS1-L5 Toshiba P/N THL64V8015ATG-5 Golden RAM P/N 76H0268 Southland Micro Systems P/N SGE SD8X64E6V AXIS StorPoint NAS 100 User’s Manual...
  • Page 92 144-pin 8-byte SO DIMM • 16Mx8 EDO DRAM based (8 pcs.) • 3.3V • 50 ns • 4K refresh cycles • A0-A11 address inputs Use this module or equivalent: Manufacturer Type Centon P/N CAX16MX64-5EVDG AXIS StorPoint NAS 100 User’s Manual...
  • Page 93 Always use an antistatic bracelet when handling the memory modules. Caution! 4. Replace the server casing. 5. Power up the unit. The new memory module is automatically identified and the usage optimized by StorPoint NAS. AXIS StorPoint NAS 100 User’s Manual...

  • Page 94: Appendix D Tower And Drive Installation

    Unpack and inspect all parts for damage. Contact your dealer if anything is missing. All packaging materials are recyclable. The standard delivery includes the following: Hardware Description Part Number AXIS StorPoint NAS 100 Wide SCSI Ethernet 0099-002-01 StorPoint NAS AXIS StorPoint NAS 100 IDE 0102-001-01 4 Screws,...

  • Page 95: Physical Description

    StorPoint NAS is equipped with a 100baseTX connector. The internal network Network Connector connector will automatically adjust to 10baseT or 100baseTX, full or half duplex mode. Use a Category 5 UTP cable for the 100baseTX operation. AXIS StorPoint NAS 100 User’s Manual...
  • Page 96 Refer to “The Front Panel Indicators ” on page 76 for a list of error conditions. The StorPoint NAS serial number is found on the labels at the underside of the Serial Number server unit and at the back of the tower. AXIS StorPoint NAS 100 User’s Manual...

  • Page 97: Installing Storpoint Nas In A Tower

    PC 4-pin power supply connector (12 and 5 V DC). Hence, the power supply available in the tower can also be used to supply StorPoint NAS. 6. Connect the external network connector board to StorPoint NAS using the shielded CAT 5 cable. AXIS StorPoint NAS 100 User’s Manual...

  • Page 98: Connecting The Hard Disks To Storpoint Nas

    5. Switch the power on to the whole of the tower. 6. The StorPoint NAS front panel indicators will flash during power-on and self- test. When the Status indicator stops flashing and turns solid green, StorPoint NAS is ready for use. AXIS StorPoint NAS 100 User’s Manual...
  • Page 99 4. Switch the power on to the whole of the tower. 5. The StorPoint NAS front panel indicators will flash during power-on and self- test. When the Status indicator stops flashing and turns solid green, StorPoint NAS is ready for use. AXIS StorPoint NAS 100 User’s Manual...

  • Page 100: Appendix E Technical Specifications

    SCSI (20 MB/sec) or ultra wide SCSI (40 MB/sec). IDE Hard Disk Up to 8 IDE/ATA-4 hard disk drives. Drive Connections Four 40 pin headers. Connector DMA Mode 2 (16.67 MB/s), PIO Mode 4 (16.67 MB/sec). Speed AXIS StorPoint NAS 100 User’s Manual...
  • Page 101 IDE - CE: EN 55022/1994, EN 55024/1998. FCC Subpart B Class A. EN 60950, UL1950. Approved power supply for all countries. Safety Warranty 3 years. All specifications are subject to change without prior notice. AXIS StorPoint NAS 100 User’s Manual...

  • Page 102: Appendix F Glossary

    [Root] Organization Acme O=Acme Organizational Unit Organizational Unit Corp Sales OU=Corp.O=Acme OU=Sales.O=Acme Servers Users Servers Users Objects in an NDS Directory Tree Domain Name Service. Reflects the server names and addresses within a network. AXIS StorPoint NAS 100 User’s Manual...
  • Page 103 NCP to provide services, such as file and print services. NetWare Directory Services. Manages network resources such as NetWare servers and volumes. Network Information Services. The security and file-access databases on UNIX systems, previously known as Yellow Pages. AXIS StorPoint NAS 100 User’s Manual...
  • Page 104 IP address mappings. Wizard A form of user assistance that automates a task through a dialog with the user in order to speed up operation. These tasks are typically complex and require experience. AXIS StorPoint NAS 100 User’s Manual...

  • Page 105: Index

    NDS frame types customized link front panel indicators access control data throughput protocol settings default password FTP commands default settings FTP user name DHCP diagnostic test AXIS StorPoint NAS 100 User’s Manual...
  • Page 106 Web (HTTP) server name Master memory check memory expansion password performance Microsoft & IBM networks physical description access control ping command configuration power supply mirroring problems monitoring ProtectIP parameter protocol settings name resolution problems AXIS StorPoint NAS 100 User’s Manual...
  • Page 107 Volumes folder BOOTP DHCP Web (HTTP) RARP access control Web browser configuration share-level mode Web browser shutdown Web interface Slave Windows SLP directory agents access control SLP scope list share-level SMB server name user-level AXIS StorPoint NAS 100 User’s Manual...
  • Page 108 Index configuration protocol settings server name WINS WINS database wizard NetWare TCP/IP Web (HTTP) Windows (SMB) AXIS StorPoint NAS 100 User’s Manual...

Table of Contents