Table of Contents
Advertisement
Chemistry Config.
Wizard + to enter
Pool/Spa Config.
+ to view/change
Pool/Spa Setup
Pool and Spa
if "Pool and Spa" is selected
Spa - CountDn
00:30
if "Pool and Spa" is selected
Spa Spillover
Enabled
if "Pool and Spa" is selected and
if "Spa Spillover" is enabled
Filter Operation
Spa Spillover
if "Pool Only" or "Spa Only" is selected
V1=Aux1, V2=Aux2
Disabled
if "Pool and Spa" is selected
Filter Off Valve
Change: Enabled
Pool/Spa Setup
If "Pool Only" or "Spa Only" are selected, then the pool/spa valves are not needed and pushing the POOL/
SPA button on the display/keypad will have no effect. If "Pool and Spa" is selected, then the pool/spa
suction and return valve actuators should be connected to the Pro Logic. Pressing the POOL/SPA button
on the display/keypad will allow the homeowner to alternate between pool and spa operation. For more
information on "Pool and Spa", refer to the Plumbing section on pages 8.
Spa CountDn
This menu will appear only if Pool/Spa Setup is set to "Pool and Spa". This setting is the time, after you
manually switch the Pool/Spa valves to "Spa Only", until the Pro Logic automatically returns the valves to
their previous positions. It is programmed in increments of 5 minutes, from "Manual On/Off" (0 minutes) to
"21:00" (21 hours). The filter is forced on during this time period.
Spa Spillover
When spa spillover is "Enabled" and "Pool and Spa", the homeowner will be able to rotate through "Pool
Only" (both suction and return valves switched to pool), "Spa Only" (both suction and return valves
switched to spa) and "Spillover" (suction valve switched to pool and return valve switched to spa) by
successive presses of the "Pool/Spa button.
Filter Operation
If "Spa Spillover" is selected, the Pro Logic will automatically switch the pool/spa suction and return
valves to "spillover" at the start of the programmed pool filtering time period or when the super-chlorinate
function is turned on. The valves will remain in this position for the remainder of the super-chlorinate
period. This option is usually preferable because both the pool and spa water will be filtered and sanitized.
If "Pool Only" is selected, then the Pro Logic will switch the pool/spa valves to the "pool only" position
at the start of the programmed pool filtering time period or when the super-chlorinate function is turned on.
This may be desirable on some systems with in-floor cleaners because it allows the cleaner to operate all
the time the pool is being filtered and/or the super chlorinate is running.
Press to access Chemistry Config. Wizard
Move to previous/next menu item
Chemistry Configuration Wizard
Requires use of the optional AQL-CHEM Sensing Kit. Following the steps of the Chemistry Config.
Wizard will set up the AQL-CHEM to sense ORP and pH levels and, if chlorination is used, can configure
the Pro Logic to generate the correct amount of chlorine to properly sanitize the pool. Refer to the AQL-
CHEM manual for more detailed information.
Push to access Pool/Spa options
Move to previous/next configuration menu
Rotates between Pool Only (default), Spa Only and
Pool and Spa
Move to next menu item
Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15..., (default is 4:00))
Move to next menu item
Toggle between Enabled and Disabled
Move to next menu item or previous/next configuration menu
Toggle between Pool Only
Move to previous/next configuration menu
Toggle between Enabled and Disabled (default)
Move to previous/next configuration menu
Toggle between Enabled
Move to previous/next configuration menu
(default)
Spa Spillover
(default)
and Spa Spillover options
(default)
and Disabled
21
Hide quick links:
Advertisement
Table of Contents
