1. Manuals
  2. Brands
  3. iSolution Manuals
  4. Lighting Equipment
  5. iMOVE 8W
  6. User manual

iSolution iMOVE 8W User Manual

Moving wash
Hide thumbs
Table of Contents

Advertisement

Quick Links

iMove 8W Moving Wash
WWW.BEGLEC.COM
Innovation , Quality , Performance

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the iMOVE 8W and is the answer not in the manual?

Questions and answers

Related Manuals for iSolution iMOVE 8W

Summary of Contents for iSolution iMOVE 8W

  • Page 1 8W Moving Wash WWW.BEGLEC.COM Innovation , Quality , Performance...

  • Page 2: Table Of Contents

    7. Fixture Cleaning The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater TABLE OF CONTENTS accumulation of dirt on the unit’s optics.

  • Page 3: Safety Instruction

    1. Safety Instruction Pay attention to the belt tension when install the belt. Please read carefully the instruction, which includes important information about the installation, usage and maintenance. Please refer to the photos below: WARNING Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet.
  • Page 4 Warning G. If The pan belt is broken To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or 1. Turn off the main power. moisture. 2. Unscrew all the screws (A) and open the base-housing cover (B). Never touch bulb with bare fingers, as it is very hot after using.

  • Page 5: Technical Specification

    2. Technical Specification 6. Troubleshooting Following are a few common problems that may occur during operation. Here are some Power supply - AC 120V ~ 60Hz / 230V ~ 50Hz suggestions for easy troubleshooting: Lamp A. The unit does not work, no light and the fan does not work - Discharge lamp MSD 250/2 GY 9.5 1.
  • Page 6 5.5. DMX512 Connection 8 Channels: The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels. Channel 1 = Pan motion Channel 2 = Tilt motion Channel 3 = Shutter Channel 4 = Effect wheel Channel 5 = Color Channel 6 = CYM Mix Color Channel 7 = Dimmer Channel 8 = CMY Speed...
  • Page 7 3. Lamp In case of replacement of the lamp or maintenance, do not open the fixture within 15 minutes until the unit cools down after switching off. Because of its high internal pressure, there might be a risk that the Discharge lamp would explode during operation.

  • Page 8: How To Set The Unit

    5.4. DMX512 Configuration 4. How To Set The Unit 4.1. Control Panel Display To show the various menus and the selected functions . DMX input present MASTER Master mode SLAVE Slave mode SOUND Flashing Sound activation Button MENU To select the programming functions DOWN To go backward in the selected functions To go forward in the selected functions...

  • Page 9: Main Function

    4.2. Main Function Stand by Blackout the unit To select any of the pre-set functions, press the MENU button up to when the required one is Strobe X/Y moving show pattern Color selection X/Y moving setting 1. Color sync. strobe selection 1.Pan position shown on the display.

  • Page 10: How To Control The Unit

    5. How To Control The Unit Channel Mode You can operate the unit in three ways: Press the MENU button up to when the is shown on the display. Pressing 1. By master/slave built-in preprogram function ENTER button and the display will blink. Use DOWN and UP button to select the 2.
  • Page 11 Blackout Mode Display Inversion It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to Press the MENU button up to when the is shown on the display. Pressing ENTER button and the display will blink.

Table of Contents