The Installation Space; Dimensions And Clearances - GE ZICS360 LH Installation Instructions Manual

THE INSTALLATION SPACE

The finished
2-5/16"
cutout width
must be
35-1/2".
10"
84-1/2" max
83-1/2" min
24" Cutout Depth
Finished
Opening
5"
3 1/2"
Water And Electrical Locations
Electrical and water supply must be located as shown.
The cutout depth must be 24"
The refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.
Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot
exceed the 24" installation depth shown. The top case
trim overlaps the bottom of the soffit.
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install
a properly grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be
located on rear wall as shown.
Note: GFI (ground fault interrupter) is not
recommended.
• Water line can enter the opening through the
floor or back wall. The water line should be 1/4"
O.D. copper tubing or GE SmartConnect
between the cold water line and water connection
location, long enough to extend to the front of the
refrigerator. Installation of an easily accessible
shut-off valve in the water line is required.
ZUG2, ZUGSS2 Unified Grille Panel Kit
• If you are installing two refrigerators, side by side,
the installation space must be 71-1/2" wide.
Note: Additional cutout width may be required when side panels
are used. Add side panel thickness to the finished cutout to
calculate rough-in width.
• The water and electrical locations for each product
must be located as shown.
• A separate 115V, 60Hz., 15 or 20 amp power supply
is recommended for each product.
Design Guide
35-1/2"
Finished Width
Wall View
6"
Electrical
Area
75" From
Floor to Bottom
of Electrical Area
5"
Water Supply
3 1/2"
™ kit

DIMENSIONS AND CLEARANCES

25-3/4" Framed Models
35"
25-3/4" Stainless Steel Models
Case Width
Case Depth
*83-1/2"
at
Rear
36" Frame to
Frame Width
Depth Including Handles:
26-7/8" Framed Models
27-3/4" Stainless Steel Models
Product Clearances
These refrigerators are equipped with a 2-position
door stop. The factory set 130° door swing can be
adjusted to 90° if clearance to adjacent cabinets or
walls is restricted.
130° Door Swing
25"
Minimum
to Wall
130°
Allow 25" minimum clearance for a full
130° door swing. Allow 15" for pan removal.
4" minimum clearance is required when door swing
is adjusted to 90°. If the 90° door stop position is
used, pan access is maintained, but pan removal is
restricted.
See illustrations pages 4 and 5 to determine door swing
interaction with adjacent cabinets or countertops.
71-1/2" Finished Width
2-5/16"
Electrical
6"
10"
84-1/2" max
24" Cutout
83-1/2" min
Depth
Finished
Opening
5"
Water Supply
26"
3-1/2"
3
* Shipping height. The
refrigerator can be adjusted
to fit into a cutout that is
83-1/2" min. to 84-1/2" max.
*84" From
height. Note that the top
Floor to
case trim at the front is
Top Frame
1/2" higher and will overlap
upper cabinetry or soffit.
Use leveling legs and wheels
for a maximum 1" height
adjustment.
90° Door Swing
90°
Wall View
24-3/16"
6"
10"
75" From
Floor to Bottom
of Electrical Area
5"
Water Supply
26"
3-1/2"
23-7/8"
Behind
Frame
36-3/4"
4" Minimum
to Wall