Related Manuals for GE ZICS36N LH
Summary of Contents for GE ZICS36N LH
- Page 1 ® GE Monogram Installation Instructions Stainless Steel Bottom Mount Built-In Refrigerators Models ZICS36N RH ZICS36N LH...
-
Page 2: Table Of Contents
Cet appareil doit être correctement mis à la terre. Consulter « Mise à terre du réfrigérateur », page 6. If you have a question concerning the instal- WARNING lation of this product, call the GE Answer ® Center Consumer Information Service at •... -
Page 3: Flush Or Semi-Flush Enclosure Installations
Design Information 36" Stainless Bottom Mount Refrigerators Advance Planning Flush or Semi-Flush Enclosure Installations 0" 3/4" True Flush Installation Semi-Flush Installation In a flush installation, These refrigerators the refrigerator doors can also be installed will align evenly with the semi-flush into an enclosure front face of adjacent cabinet using the minimum cutout doors. -
Page 4: Installation Examples
Design Information 36" Stainless Bottom Mount Refrigerators Side panels are required whenever the sides Therefore, the rough-in dimensions must of the refrigerator will be exposed. allow for side panel thickness. In both a flush and semi-flush installation, the finished 1/2" to 3/4" side panels are normally set into dimension, (the width of the opening after place and fastened to adjacent cabinetry or to side panels are installed), must accommodate... -
Page 5: Installation Preparation
Product 35" Case 10" Min. Handle on the left side, the door swings left to Dimensions 24-3/4" 36" Overall right. ZICS36N LH Handle on the right side, the door swings right to left. 26-3/4" CAUTION 84-1/2" Max. 83-1/2" Min. 73-1/2"... -
Page 6: Grounding The Refrigerator
Installation Preparation 36" Stainless Bottom Mount Refrigerators IMPORTANT - (Please read carefully) Grounding FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED. Refrigerator The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard three-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance. -
Page 7: Tools Required
Installation Preparation 36" Stainless Bottom Mount Refrigerators • Appliance hand truck • Tinsnips to cut banding • Drill and appropriate bits Tools • Tubing cutter • Stepladder • 7/16" socket with 3" extension Required • 7/16" open-end wrench • Bucket for ratchet •... -
Page 8: Step 2: Install Water Line
Installation 36" Stainless Bottom Mount Refrigerators • A cold water supply is required for automatic icemaker operation. The water pressure Step must be between 20 and 120 p.s.i. Install • Route 1/4" OD copper tubing between house cold water line and the water connec- Water Floor tion location. -
Page 9: Step 3: Install Side Panels
Installation 36" Stainless Bottom Mount Refrigerators • Side panels are required whenever the sides • If you choose to use 1/4" side panels, they of the refrigerator will be exposed and when should be inserted into the case trim as S tep installed between frameless cabinets. -
Page 10: Step 4: Install Anti-Tip Brackets
Installation 36" Stainless Bottom Mount Refrigerators WARNING Step Soffit Block ANTI-TIP PRECAUTIONS The refrigerator is heavy at the top and must be secured to prevent the possibility of tipping 83-1/2" forward. From Install Floor Anti-Tip Bottom ATTENTION of Wood Brackets Block PRECAUTIONS CONTRE LES BASCULEMENTS... -
Page 11: Step 6: Optional Anti-Tip Precaution
Installation 36" Stainless Bottom Mount Refrigerators Refrigerator Cabinet Stud Step Note: Whenever possible, perform this step for additional Door anti-tip security. This step can be used as an alternate to Step 4, Spacer Anti-Tip bracket installation, Block Secure whenever brackets cannot be Refrigerator used. -
Page 12: Step 9: Mount Top Grille Panel
Installation 36" Stainless Bottom Mount Refrigerators For shipping purposes, the top case trim is secured at 84" installation height. To raise case trim to 84-1/2" installation Step Screws height or to lower case trim to 83-1/2": Mount • Loosen 2 screws on both sides and raise or Case Trim lower the top case trim to meet soffit... -
Page 13: Step 10: Install Toekick
Installation 36" Stainless Bottom Mount Refrigerators • A standard toekick is supplied. Install with 2 screws provided, adjust to desired height and Step tighten screws. Install Important: The vented toekick must remain unobstructed for proper air circulation and operation. Toekick •... -
Page 14: Zfc1 Trim Kit For Side To Side Installation
ZFC1 Trim Kit Side to Side Installation For the ultimate in convenience, install two refrigerators side to side. This trim kit includes 6 foam spacer pads to fill the gap between the refrigerator side case trims. For a finished appearance, a trim strip is provided to conceal the side case trim of the two refrigerators. -
Page 15: Problem Solving
Solving cabinet, turn on the energy saver switch. This Value, Servistar, HWI and other leading should only occur when humidity is high. stores. It is also available through GE Parts by calling 1-800-626-2002. Order part number Operation of Refrigerator WX10X15. - Page 16 To obtain specific information concerning any ® Monogram product or service, call GE Answer Center consumer information service at 800.626.2000—any time, day or night. For Monogram local ser vice in your area, call 1-800-444-1845.