Page 2
Intended Audience Any person in charge of installing, operating, and/or maintaining this product should read the guide that shipped with it as well as this manual in their entirety before installing, operating, or maintaining this product. Disclaimer CHAUVET® believes that the information contained in this manual is accurate in all respects.
Master/Slave..........................13 Color Setting ..........................14 Dimmer Curves .......................... 14 Control Panel Lock ........................14 Color Macro Adjustment ......................14 RGB to White Adjustment ......................15 Battery Life ..........................15 Program Upload ........................15 WELL™ 2.0 User Manual Rev. 01...
The term “DMX” used throughout this document refers to the USITT DMX512-A transmission protocol. Product at Use on Dimmer Auto Programs Temporary Outdoor Use a Glance Auto-ranging battery charger (IP44) Sound Activated Replaceable Fuse User Serviceable Master/Slave Duty Cycle WELL™ 2.0 User Manual Rev. 01 Page 1 of 28...
There are no user serviceable parts inside this product. Any reference to servicing it you may find from now on in this User Manual will only apply to properly CHAUVET® certified technicians. Do not open the housing or attempt any repairs unless you are one of them.
2. Introduction Product The WELL™ 2.0 (Wireless Event Light Luminaire) is a battery powered, portable upward wash light. It consists of a single unit that contains the 12 V gel battery, the LEDs, the LED Description drivers, and the main control. The battery provides up to 12 hours of runtime.
Green Blue Strobe DMX Channel Function Saturation Value BLOC DMX Channel Function Module 1 Red Module 1 Green Module 1 Blue Module 2 Red Module 2 Green Module 2 Blue Page 4 of 28 WELL™ 2.0 User Manual Rev. 01...
Front View Power Indicator W DMX Antenna LED Panels On/Off Switch Handle LED Panel Adjust DMX In/Out Bottom View Storage Battery Switch Battery Connector Retractable Foot Foot Release Control Panel WELL™ 2.0 User Manual Rev. 01 Page 5 of 28...
4) Screw the fuse holder cap back in its place and reconnect power. DMX Linking You may link the WELL™ 2.0 to a DMX controller using a standard DMX serial connection. If using other DMX compatible fixtures with this product, it is possible to control them individually with a single DMX controller.
Master/Slave The Master/Slave mode allows a WELL™ 2.0 unit to control or more WELL™ 2.0 units Connectivity without a DMX controller. See the Master/Slave section of the Operation chapter for programming information. The master links to the slave fixtures using the standard DMX serial connection.
· Recharge the battery to full capacity before storing the unit. · Store charged unit(s) in a dry environment, away from direct sunlight. · Turn the battery storage switch off if storing the unit for more than seven days. WELL™ 2.0 User Manual Rev. 01 Page 9 of 28...
· Once fully charged, while still connected to the battery charger, the green power indicator LED will turn off. Battery Connector Flight Case/Charger Power Input Panel Page 10 of 28 WELL™ 2.0 User Manual Rev. 01...
Wireless The WELL™ 2.0 can operate in W-DMX mode up to 300 m (900 feet) from the W-DMX transmitter. The W-DMX receiver in the WELL unit must be paired with the W-DMX Operation transmitter for wireless operation. Initial Setup 1) Turn the W-DMX transmitter on.
Control Options You can set the WELL™ 2.0 start address in the 001~512 DMX range. This allows for the control of up to 42 fixtures in the 12-channel TOUR personality. Programming Refer to the Menu Map on page 17 to learn how the menu options relate to each other.
8) Repeat the settings of colors and effects for the other scenes. Master/Slave The Master/Slave mode allows a group of WELL fixtures (the slaves) to simultaneously duplicate the output of another WELL (the master), whether static mode settings or auto/custom programs, without a DMX controller.
Continued from previous page Color Setting The COLOR setting determines how the WELL generates the white color based on various RGB settings. 1) Go to SET. 2) Select COLO. 3) Select OFF, RGBW, or UC. OFF: When the RGB faders are all set to “255”, the output is maximum, although the resulting white color may not be balanced.
LIFE parameter is set to LONG, the battery life extends to approx. 12 hours. Program Upload This option allows the user to copy the custom programs of one WELL fixture onto other WELL fixtures by using the Master/Slave method.
· Channel 9 controls the strobe frequency (not the intensity) of channels 2 through 7. Strobe · Channel 9 can strobe channels 2 through 7 when the WELL is not running macros (channel 8 inactive), thus allowing the individual color faders as well as channel 1 (Dimmer) to control the output intensity.
Module 1 Green 000 ó 255 0~100% Module 1 Blue 000 ó 255 0~100% Module 2 Red 000 ó 255 0~100% Module 2 Green 000 ó 255 0~100% Module 2 Blue WELL™ 2.0 User Manual Rev. 01 Page 19 of 28...
· Gently polish the LED lens cover until it is free of haze and lint. Always dry the LED lens cover carefully after cleaning it to prevent stains and discoloration. Page 20 of 28 WELL™ 2.0 User Manual Rev. 01...
WELL and transmitter not paired Pair the WELL to the W-DMX transmitter WELL beyond transmitter’s range Move the W-DMX transmitter closer to the WELL Interference from other equipment Reposition the WELL for better reception If you still experience technical problems after trying the above solutions, contact CHAUVET®...
Be sure to pack the fixture properly. Any shipping damage resulting from inadequate packaging will be the customer’s responsibility. As a suggestion, proper UPS packing or double boxing is always a safe method to use. CHAUVET® reserves the right to use its own discretion to repair or replace returned product(s). Claims The carrier is responsible for any damage incurred during shipping to this product or any part that shipped with it.