Mark Levinson 31 Manual

Mark Levinson 31 Manual

Reference cd transport

Advertisement

Phonograph records
vs. compact discs
Tracks and indexes
About Compact Disc
Digital Audio...
To most people, a Compact Disc (CD) looks like a small, silver
phonograph record. In fact, there are some important differences
between records and CDs.
The information on a phonograph record is contained within its
grooves. This analog information is
read by a stylus riding along in
the grooves and transmitted
via a cartridge. The digital
information on a CD,
though arranged in
similar grooves, is read
by a laser mechanism
(called a pickup ). A
phonograph's stylus
must be in contact
with the record, but a
CD player's pickup
never touches the CD.
The information on the
CD is transmitted via
complex decoder circuitry.
The CD rotates
counterclockwise, and the laser
pickup reads the underside of the CD
(the side opposite the label) beginning at the center and travelling
toward the outer edge. As the pickup moves away from the center,
the speed of rotation gradually decreases from 500 to 200 revolutions
per minute.
Programs on CDs are organized into tracks , usually corresponding to
songs or movements. This allows you to select a part of a program
Lindsay's First Symphony
First Movement
Second Movement
(Track 1)
(Track 2)
Index Numbers from Track 2
01
02
03
04
05
06
allow even more precise selection and programming. A single track
may have up to 99 indexes.
Direction the disc rotates
easily and precisely,
with virtually no wear
and tear on the CD.
Third Movement
There may be as many
(Track 3)
as 99 tracks on a CD.
On some CDs, tracks
are further broken down
94
95
96
97
98
99
into indexes . These
"tracks within tracks"
Direction the laser
pickup travels
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 31 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Mark Levinson 31

  • Page 1 About Compact Disc Digital Audio… To most people, a Compact Disc (CD) looks like a small, silver phonograph record. In fact, there are some important differences between records and CDs. Phonograph records The information on a phonograph record is contained within its vs.
  • Page 3: Front Panel

    Pressing standby again places the Nº31 into standby mode and disables the front-panel controls. While the Nº31 is in standby mode, the Display is dark and the standby LED flashes slowly. When the Nº31 is ready to operate (not in standby mode), the standby LED remains lighted.
  • Page 4 Pressing this button varies the brightness of the Display. Four brightness levels are available. When the Nº31's main power switch is first turned on (or when power is restored after an interruption), the Display is automatically set to its second-brightest level.
  • Page 5 CD (or the first track in the program), the Nº31 will play the first ten seconds of the track, skip to the second track and play the first ten seconds of that track, and so on.
  • Page 6 After you view the last selection in the program, the Display will show PROGRAM END. If you press program review when there is no program in the Nº31's memory, the Display will show NO PROGRAM. 12 program save Pressing this button records a program in the Nº31's memory.
  • Page 7: Top Panel

    Top panel Laser Isolation Device (LID) The LID covers the CD transport assembly, the mechanism that holds the CD during play. Its operation is controlled by the LID Open/Close button (2). PRECAUTION Never hold onto the LID while it’s opening or closing. LID Open/Close Pressing this button opens the LID (1);...
  • Page 8 (See "Linked functions.") When you release Search Reverse, play normally resumes. If you have reached the beginning of the disc, the Nº31 will Stop and wait for your next command. Play After a CD is loaded and the Disc Damper is in place, pressing this button begins play with the first track on the CD (or the first track in a program).
  • Page 9 This button works in the same way as Previous (8), except that it skips to the next track or index. While the Nº31 is in index mode, pressing Next skips the laser pickup to the next index . If index mode is inactive, pressing Next skips the laser pickup to the next track .
  • Page 10: Cd Transport Assembly

    Four levelling screws (one inside each finger well) allow you to adjust the transport assembly. With the supplied 3/32" hex driver, and using the Nº31's bubble level (3) as a gauge, adjust one or more of these screws to bring the transport assembly to level.
  • Page 11 Never touch or attempt to clean the laser assembly. PRECAUTION Disc Damper To clamp a CD onto its spindle, the Nº31 uses a Disc Damper held in place by a strong magnet. Always make sure that the Disc Damper is in place before closing the LID.
  • Page 12 CD. During play, this part of the Display shows the number of the track in play. While a program is in the Nº31's memory, the letter P will appear preceding the track number. A small indicates a saved polarity setting (possible only when the Nº31 is linked to a compatible Mark...
  • Page 13 FIRST TRACK: The Previous button was pressed while the first track on the CD (or in a program or a random sequence) was playing. INDEX SEARCH: The Nº31 is scanning the CD for indexes; appears after index mode is pressed.
  • Page 14: Remote Control

    Next or Previous) or, along with prg/time (3), to begin play at a specific time in a track. Note: If the Nº31 is in index mode, the numbered buttons select indexes. If the index mode is inactive, the numbered...
  • Page 15 Some recordings simply "sound better" when polarity is inverted. When the Nº31 is linked to a compatible Mark Levinson digital processor (via their communication ports), pressing this button inverts polarity on the digital processor. (See "Rear panel" and...
  • Page 16 Control. It lights when you press any button on the Remote Control. Note: This LED indicates when the Remote Control sends a command, not necessarily that the Nº31 received it. If this LED fails to light when a button is pressed, replace the Remote Control's batteries.
  • Page 17 Projection lens Infrared (IR) commands from the Remote Control to the Nº31 are transmitted through this lens. (See "Set-up and installation.") 30 feet or less 30˚ 30˚ Always keep the projection lens clean.
  • Page 18: Rear Panel

    AC operating voltage for your location. (See "Set-up and installation"). main power This switch turns the Nº31 on and off. The switch must be in the "|" (on) position for the Nº31 to function. (See "Set-up and installation.") PRECAUTION...
  • Page 19 These communication ports allow the Nº31 to "link" to certain compatible Mark Levinson components. (See "Linked functions.") Using the Link cable, connect the Nº31's slave in port to the master port on the Mark Levinson digital processor. Make sure that the Link cable's locking tabs engage securely in the components' communication ports.
  • Page 21: Setup And Installation

    1. Make sure that the Nº31 is unplugged from the AC power supply and disconnected from your digital processor. 2. Place the Nº31 upright on a flat, stable surface. Carefully tip it so it rests on its side ; protect its finish with a soft cloth.
  • Page 22 3. The Nº31 is shipped so that it rests solidly on its four feet, one under Installing the spikes each corner of the unit. (optional) You may want to explore the potential sonic advantages of installing the specially designed "spikes" supplied with the Nº31.
  • Page 23 To allow heat dissipation through air circulation, allow 3 to 4 inches of clearance above the vents on the top of the Nº31. Never block the vents on the bottom of the Nº31. To help with special installations and custom cabinetry, drawings are included in this manual.
  • Page 24 If the Nº31 will be subject to direct sunlight, place it no more than 10 feet from where you’ll normally operate the Remote Control. Where bright sunlight virtually floods the room, IR communication may not be possible. In a room lighted primarily with incandescent fixtures, place the Nº31 no more than 25 feet from where you’ll normally operate the...
  • Page 25 The quality of the cables and connectors that you use with your Nº31 can noticeably affect the quality of the sound that you hear from your speakers or headphones. For electrical interconnection, we recommend Madrigal Audio Laboratories MDC cable.
  • Page 26 Nº31 Voltage setting 11. The Nº31 is set internally for 100V, 120V, 200V, 220V, or 240V AC mains operation @ 50 or 60Hz. Make sure that the label on the rear panel of your Nº31 indicates the correct AC operating voltage for your location.
  • Page 27 Connect the AC cord to the AC power cord socket on the rear Connecting the panel of the Nº31 (see "Rear panel"), then connect the AC cord AC power cord to the AC mains. To Nº31 To AC mains 1 = Line (hot)
  • Page 28 Four levelling screws (one inside each finger well) allow you to adjust this. With the supplied 3/32" hex driver, and using the Nº31's bubble level as a gauge, adjust one or more of these screws to bring the transport assembly to level. To lower a corner, turn the corresponding screw clockwise;...
  • Page 29 15. Using the supplied 1/16" hex key, remove the two screws securing Installing batteries in the the cover of the Remote Control’s battery compartment (the end Remote Control opposite the projection lens). Projection lens – – 16. Insert two AA batteries according to the symbols on the inside of the battery compartment cover.
  • Page 31: Basic Operation

    Basic operation Before operating your Nº31, become familiar with its controls and their locations. (See "Front panel," "Top panel," "CD transport assembly," and "Remote Control.") To load a CD for play: Loading a CD 1. Make sure that the main power switch is set to the "|" position.
  • Page 32 Once a CD is loaded and ready for play, press preview. Beginning with the first track, the Nº31 will play the first ten seconds of the track, skip to the second track and play the first ten seconds of that track, and so on.
  • Page 33 Using indexes If a CD has indexes, you may use them to begin play in the middle of a track. 1. Press index mode. (If there was no CD in play, the Display will show INDEX SEARCH.) In a few seconds, the LED above the button will flash.
  • Page 34 Display. To return to normal play, press the repeat A>B button again, or press Play. Inverting playback polarity If your Nº31 is linked to a compatible Mark Levinson digital processor via the communication ports, you may change the playback polarity. (See "Linked functions.") After loading a CD, press the polarity invert button on the digital processor's front panel, or press d/a polarity on the Nº31's Remote...
  • Page 36 How the Nº31 When you load a CD, the Nº31 assigns it a unique identification code. "remembers" programs If you assemble a program for a particular CD and save it into the Nº31's memory, the Nº31 "remembers"...
  • Page 37 If you want to play your program without recording it in the Nº31's memory, go on to step 6. b. If you want to record your program in the Nº31's memory, press program save; the Display will show NEW PROGRAM.
  • Page 38 If you want to play your program without recording it in the Nº31's memory, go on to step 6. b. If you want to record your program in the Nº31's memory, press program save; the Display will show NEW PROGRAM.
  • Page 39 Next and Previous (or the numbered buttons on the Remote Control) to select an index. Note: If your Nº31 is linked to a compatible Mark Levinson digital processor via the communication ports, you may set the playback polarity independently for each track. (See "Linked functions.")
  • Page 41: Linked Functions

    CD that's playing, even though it's being recorded, press the Stop button twice in succession.) When the Nº31 is first turned on, the record link setting is off . Mute link Mute link: This link automatically mutes the volume during search (that is, whenever you press Search Forward or Search Reverse).
  • Page 42 When you select the Nº31's input, the Nº30 will show No31 on its Display. When the Nº31 is first turned on, the alias link setting is on . Play link Play link: When you press the Nº31's Play button, this link automatically selects the Nº31's input on the digital processor.
  • Page 43 Changing link settings The Nº31 allows you to change the Index 0 option and six of its link settings to suit your own preferences. Note: The polarity link setting is always on , and can't be changed. 1. Make sure that the main power switch is set to the "on" ("|") position.
  • Page 45: Troubleshooting

    The transport screws weren’t removed during set-up. There may be condensation (moisture) on the laser pickup. This can happen if the Nº31 is moved from a cold environment to a warm one. Set the main power switch to its "|" position, and leave it on for an hour before playing a CD.
  • Page 46 The Remote Control is at the wrong angle relative to the Nº31, and the Nº31 can’t receive the signal. The sensor window on the front panel of the Nº31 is dirty or blocked. The Remote Control’s projection lens is dirty.
  • Page 47: Care And Maintenance

    Care and maintenance Nº31 To remove dust from the cabinet of the Nº31, use a feather duster. To remove dirt and fingerprints, we recommend isopropyl alcohol applied to a soft cloth. Don’t apply water, dusting sprays, solvents, abrasives, or cleaning fluids directly to the cabinet.
  • Page 48: Specifications

    2 RJ45 connectors 1 IEC mains connector If purchased in North America, this Mark Levinson product’s warranty is owner-transferable. Warranty conditions are valid only in the country where the product was originally purchased. For warranty information and conditions on products purchased outside of North America,...
  • Page 49 Dimensions 19.375" 5.560" 1.100" 11.861" 13.726" 12.261"...
  • Page 50 14.426" 5.432" .308"...
  • Page 52 MADRIGAL AUDIO LABORATORIES 2081 South Main Street, P.O. Box 781 Middletown, Connecticut 06457 USA Telephone: (203) 346-0896 Fax: (203) 346-1540 ® is a registered trademark of Madrigal Audio Laboratories, Inc. ©1992 Madrigal Audio Laboratories, Inc. All rights reserved. 630110-1 Printed in U.S.A.

Table of Contents

Save PDF