Setting Bass Sound Control; Setting Bass Compressor; Setting Bass Focus; Speaker Setup - Alpine IVA-D310RB Owner's Manual

Adjusting the Frequency
Touch [ ] or [ ], then adjust the frequency of the
selected band.
Adjusting the Level
Touch [ ] or [ ], then adjust the level of the selected
band.
Selecting the Band
The band (BAND1 through BAND5) changes each time
[BAND] is touched.
The active bar and the variable range of the center
frequency move according to the band.
• Touching outside the variable range for a selected band moves the
active bar to a band where the touched position can be adjusted.
Setting the Bandwidth
The bandwidth changes each time [Q] is touched.
Adjusting the Level/Frequency Directly
Move to a desired position by touching the active point and
change the setting contents. Or, move the active point to the
desired position by touching where you wish to move it.
• Downloading is stopped, and the setting contents (created before
stopping by touching [CANCEL] in the display during the download,
or operating the connected audio processor) are displayed.
• Loading time may take longer depending on the setting content. This
is not a malfunction.
9
Touch [RETURN] to return to the previous screen.
• When the speaker is set to the "OFF" mode, the parametric
equalizer for that speaker cannot be set. Refer to "Setting the
Speakers" (page 47).
• It is not possible to adjust the frequencies of adjacent bands within 7
steps.
• Check the playable frequency ranges of the connected speakers
before making the equalizer adjustments. If the speaker's playable
frequency range is 55 Hz to 30 kHz, for example, adjusting the 40 Hz
or 20 Hz band has no effect. Additionally, you may overload and
damage the speakers.
• When the parametric EQ is adjusted, the adjustment for graphic EQ
becomes ineffective.

Setting Bass Sound Control

1
Make sure that the defeat is turned off.
2
Touch [SETUP] on the main source screen.
The SETUP selection screen is displayed.
3
Touch [i-Personalize].
The i-Personalize screen appears.
4
Touch [ ] of A.PROCESSOR.
The A.PROC list is displayed.
5
Touch [ ] of BASS SOUND CONT.
The Bass Sound Cont. screen appears.

Setting Bass Compressor

You can adjust the sound of low frequencies as desired.
6
Touch [ ] or [ ] of BASS COMP. to select the
desired mode.
Bass sound is emphasized more as the mode is
sequentially switched as MODE1
vivid low frequencies.
Select OFF when the setting is not necessary.
Touch [RETURN] to return to the previous screen.

Setting Bass Focus

Using the previously specified delay number (time difference) allows
you to set a time difference between the front-rear/left-right speakers.
Namely, it enables a time correction based on your preference. With an
initial delay of 0.05 ms for each of the 0 to 400 steps, audible time
correction can be achieved.
6
Set the delay number in the front and rear, and on
the right and left of the desired speaker by touching
the respective [ ] or [ ] button.
• Any setting in Bass Focus is applied in time correction, too.
• Touch [RETURN] to return to the previous screen.

Speaker Setup

The PXA-H700 or PXA-H701 can be set according to the playable
frequency range of your speakers.
Check the playable frequency range of the speakers (not including the
subwoofer) before performing this operation to verify whether the
speakers can play low frequencies (of about 80 Hz or less).
• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is cancelled if Decode mode is switched.
1
Check that Defeat mode is off (page 25).
2
Touch [SETUP] on the main source screen.
The SETUP selection screen appears.
3
Touch [i-Personalize].
The i-Personalize screen will appear.
4
Touch [ ] of A.PROCESSOR.
The A.PROC list screen appears.
5
Touch [ ] of SPEAKER SETUP.
The adjusting screen of SPEAKER SETUP appears.
6
Select the speaker characteristic by touching [ ],
[ ] or [ON], [OFF] of the desired speaker setting.
1
OFF* : When no speaker is connected.
When a speaker that cannot play low frequencies
SMALL:
(80 Hz or less) is connected.
2
LARGE* : When a speaker that can play low frequencies (80
Hz or less) is connected.
1
* It is not possible to set the front speakers to "OFF".
2
* If the front speakers are set to "SMALL", the rear and
centre speakers cannot be set to "LARGE".
• If the centre speaker is turned "OFF," the centre channel's audio
signals are added to the audio signals output from the front speakers.
2 3, offering you
51
-EN