Emissions Information; Generalrecommendations; Generatormaintenance; Tocleanthegenerator - Generac Power Systems XG Owner's Manual

3.2.3 EMiSS/ONS /NFORMAT/ON
The Environmental Protection Agency (EPA) requires that this
generatorcomply with exhaustandevaporativeemissionstandards.
This generator is certified to meet the applicable EPA emission
levels on gasoline.The emission control system on this generator
consists of the following:
• Fuel System • Air Induction System
Carburetor - Intake Pipe/manifold
FuelTank!cap - Air Filter
FuelLines o Ignition System
EvaporativeVent Lines _ Spark plug
Exhaust System - Ignition module
ExhaustManifold • Exhaust System
Muffler _ ExhaustManifold
It is importantto perform the service specifiedin the Maintenance
Scheduleto ensurethat the generatorcomplies with the applicable
emission standards for the duration of its useful life. Additionally,
emissions critical maintenancemust be performed as scheduled
in order for the Emissions Warrantyto be valid. Emissions critical
maintenanceconsists of servicing the air filter and spark plugs in
accordance with the MaintenanceSchedule. Service and repairs
may be performed by any capableperson or repair shop.
3.3 GENERAL RECOMMENDATIONS
Thewarranty of the generatordoes not cover itemsthat have been
subjected to operator abuse or negligence. To receive full value
from the warranty, the operator must maintain the generator as
instructed in this manual.
Some adjustments wilt need to be made periodically to properly
maintain the generator.
All adjustments in the Maintenancesection of this manual should
be madeat least once eachseason. Followthe requirementsin the
"MaintenanceSchedule".
NOTE:
Once a year replace the spark plug and replace the air filter.
A new spark plug and clean air filter assure proper fuel-air
mixture and help the engine run better and last longer.
3.3.1 GENERATOR MAINTENANCE
Generatormaintenanceconsists of keepingthe unit clean and dry.
Operateand store the unit in a clean dry environmentwhere it will
not be exposed to excessive dust, dirt, moisture or any corrosive
vapors.Coolingair slots in the generatormust not becomeclogged
with snow, leaves,or any otherforeign material.
Checkthe cleanlinessof the generatorfrequently and clean when
dust, dirt, oil, moisture or other foreign substances are visible on
its exteriorsurface.
_,CAUTION!
Never insertany object or toolthroughthe air cooling
slots, even if the engineis not running.
NOTE:
DO NOT use a garden hose to clean generator. Water can
enter the engine fuel system and cause problems. In addition,
ff water enters the generator through cooling air slots, some
water will be retained in voids and crevices of the rotor
and stator winding insulation. Water and dirt buildup on the
generator internal windings will eventually decrease the
insulation resistance of these windings.
3.3.2 TOCLEANTHEGENERATOR
• Use a damp cloth to wipe exteriorsurfaces clean.
• A soft, bristlebrush may be usedto loosencakedon dirt, oil, etc.
• A vacuumcleanermay be usedto pick up loose dirt and debris.
• Low pressure air (not to exceed 25 psi) may be used to
blow away dirt. Inspect cooling air slots and openings on the
generator. T heseopeningsmust be kept cleanandunobstructed.
3.3.3 ENGINE MAINTENANCE
,_ CAUTION!
When workingon the generator, always disconnect
negativecable from battery. Also disconnect sparkplug
wire from spark plug and keep wire away from spark
plug.
3.3.4 CHECKING OILLEVEL
See the "BEFORESTARTINGTHE GENERATOR"section for
information on checking the oil level. The oil level should be
checkedbeforeeach use,or at least everyeight hoursof operation.
Keepthe oil levelmaintained.
3.3.5 CHANGING THEOILANDOILFILTER
Change the oil and filter after the first 30 hours of operation.
Change the oil every 100 hours or every season thereafter. If
running this unit under dirty or dusty conditions, or in extremely
hot weather,changethe oil more often.
Not oil may causeburns. Allow engineto cool before
draining oil. Avoidprolongedor repeatedskin exposure
with used oil. Thoroughly washexposedareas with soap.
Use the following instructions to changethe oil:
• Cleanarea around oil drain cap.
• Removeoil drain cap from the drain hose and oil fill plugto drain
oil completely into a suitable container.
• Whenoil has completelydrained,install oil drain cap and tighten
securely.
• Place a suitable container beneath the oil filter and turn
filter counterclockwise to remove. Discard according to local
regulations.
13