Monogram ZIRS36N LH Installation Instructions Manual page 15

ZUGSS Trim Kit
Unified Stainless Steel Grille Panel
Step 2
Install
Anti-Tip
Brackets
ANTI-TIP PRECAUTIONS
These products are heavg at the top and must
be secured to prevent the possibilitg of tipping
over.
Brackets Brackets
Required Net Required
Beneatha
Soffit
Step 3
Level Both
Products
PRECAUTIONS CENTRE LES BASCULEMENTS
Le r@frig@rateur est beaucoup plus Iourd en haut
et il faut le maintenir en place pour 8viter la
possibilit@ de son basculement vers I'avant.
• Cut a 2"x4" block, 71" long. Secure the 2"x4" to the
4 mounting brackets provided using #12 or #14
wood screws.
• Secure the brackets with wood block to the buck
wall so that it is 84" (or 9our installation height)
from the finished floor. Use #12 or #14 wood
screws. See illustration.
• Screws must penetrate at least one inch into
vertical wall studs.
Roll Both Products into Opening
• Gently push each product into opening with hands
against front corners. Push buck into the opening
until it is flush or semi-flush with adjacent cabinets.
2x4Cut _-_'-
71" Length
SideView
Installation Mounting
Height Bracket
FromFloor
Screws Mounted into J_
Vertical Wall Studs
IMPORTANT NOTE: When the products ere installed under
o soffit or if there is not enough height for this method of
security, use Step/4 Qs an Qlternative. The refrigerator end
freezer must be secured to prevent tipping.
Both products MUST BE LEVEL AND PLUMB with each
other and adjacent cabinetrg on each side. Toekick
heights should elign with cebinetrg.
• Adjust carefull 9. Both models have 4-point leveling.
The front is supported by leveling legs, the reer is
supported by wheels.
• Raise units to the some level, eligning with adjecent
toekick heights.
• Adjust rear wheels beneath the product to just barel 9
touch the 2×4 block.
• Turn the 7/16" hex nut Ioceted ebove the front wheels
to raise or lower the buck of the refrigeraton
• To udjust the front leveling legs: Use a 1/4" angled
L
HexNutAdj usts ] o ii i
RearWheels )l_l] I
o o0_ o
Units must be i" apart and evenly aligned at top
wrench to turn the top of the leveling leg, or turn the and bottom. The inside case trims must align, top
bottom of the legs with a 1-1/4" wrench, and bottom.
The rear leveling wheels and front leveling legs
(]re limited to a maximum height adjustment of
l". If the installation requires more then 84-1/2"
height, the installer should elevate the
refrigerator on a sheet of pigweed or runners.
Cabinetrg trim could also be added across the
top of the opening to shorten the opening. If you
attempt to raise the refrigerator more than 1",
gou will damage the front leveling legs and
rear leveling wheels.
Les roues de nivellement arri_re et les pattes de
nivellement avant permettent un r6glage maximal
de 25 mm (1 po). Si I'ouverture pour le r6frig_reteur
a une hauteur sup_rieure 6 2,15 m (84-Z/2 po),
I'installateur dolt 61ever le r_frig_rateur surune
feuille de contre-plaqu& ou des glissi6res. II est
_galement possible d'ajouter des baguettes de
finition des placards sur le haut de I'ouverture (]fin
de la r_duire. Lever le r_frig_rateur de plus de 25
mm (1 po} endommoge les pattes de nivellement
event et les roues de nivellement arri_re.
15