14: Vocal Echo; 15: Band Pass Delay - Roland V-Synth XT Owner's Manual

Effects List

14: Vocal Echo

This effect simulates a karaoke echo.
fig.MFX-14
L
LPF ECHO
R
Parameter Value
Delay Time #1 0–650 ms, note
Pre LPF Freq 500–15000 Hz,
THRU
Mod Rate 0.05–10.0 Hz,
note
Mod Depth 0–127
Diffusion 0–100
Feedback #2 -98– +98%
Hi Damp Freq 500–15000 Hz,
THRU
Echo Level #3 0–127
Ps Low Freq 50–4000 Hz
Ps Low Gain -15– +15 dB
Ps Hi Freq 2000–20000 Hz
Ps Hi Gain -15– +15 dB

15: Band Pass Delay

This is a delay with a band pass filter (a filter that outputs only a
specified frequency range) on each of five delays. A phaser is
included before the delay. Phaser is an effect that adds a phase-
shifted sound to the original sound to create time-varying change,
modulating the sound.
fig.MFX-15
L
Phaser
R
1
BPF 1
2
BPF 2
3
BPF 3
4
BPF 4
5
BPF 5
172
2-Band
EQ
Description
Adjusts the delay time from the
direct sound until the delay
sound is heard.
Sets the filter's cutoff frequency
(THRU: no filter is used)
Specifies the modulation speed
of the modulation effect.
Specifies the modulation depth
of the modulation effect.
Specifies the spaciousness of the
delay sound.
Adjusts the proportion of the de-
lay sound that is fed back into
the effect. Negative (-) settings
will invert the phase.
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut.
High Damp, by attenuating the
higher frequencies first, makes
the delay sound more natural.
Volume of the echo sound
Frequency of the low range
Gain of the low range
Frequency of the high range
Gain of the high range
1
2
3
Delay
4
5
Parameter Value
Phaser Manual 0–127
Phaser Rate 0.05–10.0 Hz,
note
Phaser Depth 0–127
Phaser Reso- 0–127
nance
Phaser Mix Lev- 0–127
el
Delay Time 0–1300 ms, note Adjusts the delay time from the
Fbk Dly Time 0–1300 ms, note Adjusts the delay time for the
Dly Time Dev 0–1300 ms, note Specifies the differences in delay
Delay Level 0–127
Delay Feedback -98– +98%
#1
Delay Pan Type 1–10
BPF 1–5 Freq 50–20000 Hz
BPF 1/2 Q 0.3–24.0
BPF 3/4/5 Q
Balance #2 DRY100:0WET–
DRY0:100WET
Delay Pan Type
Values Dly 1 Dly 2
1 L63 L32
2 L63 32R
3 L63 63R
4 32R L32
5 63R 0
6 L32 32R
7 0 63R
8 0 63R
9 0 32R
10 63R 32R
Description
Specifies the center frequency at
which the sound is modulated.
Specifies the frequency of mod-
ulation.
Specifies the depth of modula-
tion.
Specifies the amount of feed-
back for the phaser.
Higher settings will give the
sound a stronger character.
Specifies the volume of the
phase-shifted sound, relative to
the direct sound.
direct sound until the each delay
sound is heard.
feedback sound.
time for each of the delay
sounds.
Adjusts the volume of each de-
lay sound.
Adjusts the proportion of the de-
lay sound that is fed back into
the effect. Negative (-) settings
will invert the phase.
Specifies the pan of each delay
sound.
Ten settings are provided as var-
ious panning combinations of
the delay sounds (see below).
Sets the center frequency for
each band pass filter (1–5).
Specify the output bandwidth
for each band pass filter (1-5).
Volume balance between the di-
rect sound (DRY) and the delay
sound (WET)
Dly 3 Dly 4 Dly 5
0 32R 63R
L32 63R 0
L32 32R 0
L63 0 63R
L63 L32 32R
L63 63R 0
L63 32R L32
L32 32R L63
L32 63R L63
0 L32 L63