Option Selections - Kenmore 665.15922 Use & Care Manual

You can customize your cycles by pressing an option, If you
change your mind, press the option again to turn the option off,
or select a different option if desired,
You can change an option anytime before the selected option
begins, For example, you can press an unheated drying option
any time before drying begins,
Press START to use the same cycle and option(s) as the previous
wash cycle,
NOTE: If the last cycle you completed was a rinse cycle, when
you press Start, the dishwasher runs the last full wash cycle and
options.
Hi Temp Scrub
Select this option to increase the target water temp. during the
wash portions of the cycle. Hi Temp Scrub raises the target water
temp. to 145% (63°C) in the main wash. In the Anti Bacterial
cycle, Hi Temp Scrub also raises the target water temp. to 135°F
(57°C) in the pre-wash. Heating the water helps improve washing
results. Hi Temp Scrub is useful when loads contain baked-on
food.
This option adds heat and wash time to the cycle. When Hi Temp
Scrub is used with the Anti Bacterial cycle, water is also added to
the cycle.
NOTE: Hi Temp Scrub is an option with Anti Bacterial and Pots
Pans cycles.
Sani Rinse
Select this option to raise the water temperature in the final rinse
to approximately 160°F (70°C) for 10 minutes. Sani Rinse adds
heat and time to the cycle. In the Normal cycle this high-
temperature rinse sanitizes your dishes and glassware in
accordance with the NSF International requirements
(#95/480/05/2480).
NOTE: The Anti Bacterial cycle automatically uses this option.
Sani Rinse is an option with the Pots Pans cycle.
Air Dry
Select this energy-saving option to dry without heat, Air drying is
useful when loads contain plastic dinnerware that may be
sensitive to high temperatures.
LOCKON
The dishes take longer to dry and some spotting can occur. For
best drying, use a liquid rinse aid. Some items (such as plastics)
may need towel drying.
NOTE: Air Dry is an option with all cycles, except Quick Rinse.
Lock On
Use the Lock to prevent your dishwasher from accidentally being
turned on, Use the Lock, also, to prevent accidental cycle or
option changes during a cycle,
LOCKON
When LOCK ON is lit, all buttons are disabled.
NOTES:
• The dishwasher door can be opened while the controls are
locked.
• You can turn on the Lock while the dishwasher is running.
TO turn on the Lock
Press and hold
LOCK ON
for 4 seconds. LOCK ON glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times.
TO turn off the Lock
Press and hold AIR DRY for 4 seconds. The light turns off.
Delay Hours
Select this option to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay countdown. After adding items, close the door firmly until it
latches. The delay countdown will not continue if the door is not
latched.
• You can delay the start of a cycle up to 12 hours.
• The first time you use Delay Hours, you will see
showing a 1 hour delay.
To delay the start
1. Close the door.
2. Select a wash cycle and options.
3. Repeatedly press
@
until you see the desired hours of delay in the display,
When the delay reaches 12 hours, the delay turns off. Press
DELAY HOURS again to select a new number of delay hours.
4. Press START.
NOTE: To cancel the delay and cycle, press CANCEL/DRAIN, To
cancel the delay and start the cycle immediately, press START
again,
IMPORTANT:
• Operate your dishwasher only when you are at home,
• If your home is equipped with a water softener, do not start
the dishwasher during the regeneration of the softener.
15