Intel P8700 - Core 2 Duo Processor Product Manual

1 1 1
/ - / - / DIN LIMIT CONTROLLERS
16 8 4
CONCISE PRODUCT MANUAL (59333-2)
CAUTION: Installation should be only performed by
technically competent personnel. Local Regulations
regarding electrical installation & safety must be observed.
1. INSTALLATION
The models covered by this manual have three different DIN case sizes (refer to
section 9). Some installation details vary between models. These differences have
been clearly shown.
Note: The functions described in sections 2 thru 8 are common to all models.
Installing Option Modules
1
/ Din Size Instruments
16
CPU PCB
Mounting Struts
Option Module A
Option Module 1
(Fixed Limit Relay)
Option Module 3
Option Module 2
PSU PCB
1 1
/ & / Din Size Instruments
8 4
CPU PCB
Mounting Struts
Option Module B
( not used on Limit
Option Module A
Controllers)
Option Module 2
Option Module 3
Option Module 1
PSU PCB
(Fixed Limit Relay)
To access module A, first detach the PSU and CPU boards from the front by lifting
first the upper, and then lower mounting struts. Gently separate the boards.
a. Plug the required option modules into the correct connectors, as shown below.
b. Locate the module tongues in the corresponding slot on the opposite board.
c. Hold the main boards together while relocating back on the mounting struts.
d. Replace the instrument by aligning the CPU and PSU boards with their guides
in the housing, then slowly push the instrument back into position.
Note: Option modules are automatically detected at power up.
Option Module Connectors
1
/ Din Size Instruments
16
Option Slot 1 Option Slot A
(Fixed Limit
Connectors
Relay)
PL5 & PL6
Option Slot 2
Option Slot 3
Connector
Connector
PL4A
PL4B
1 1
/ & / Din Size Instruments
8 4
Option Slot B
(not used on
Limit Cont rollers)
Option Slot 2
Connector
PL4A
Option Slot 1
(Fixed Limit
Relay)
Option Slot A
Connectors
PL5 & PL6
Option Slot 3
Connector
PL4B
Panel-Mounting
The mounting panel must be rigid, and may be up to
6.0mm (0.25inch) thick. Cut-out sizes are:
Cut-Out Dim A Cut-Out Dim B
1 1 1
/ & / Din = 45mm / Din = 45mm
16 8 16
1 1 1
/ Din = 92mm / & / Din = 92mm
4 8 4
A
For n multiple instruments mounted side-by-side, cut-out
1 1 1
A is 48n-4mm ( / & / Din) or 96n-4mm ( / Din)
Tolerance +0.5, -0.0mm
16 8 4
Slide mounting clamp
over the instrument
Mounting Panel housing towards rear face
of mounting panel until
Instrument the tongues engage in
Housing ratchets and instrument is
clamped in position.
Ratchets
Gasket Hold instrument firmly in
position (apply pressure
to bezel only)
CAUTION: Do not remove the panel gasket; it is a seal against dust and
moisture.
Rear Terminal Wiring
USE COPPER CONDUCTORS (EXCEPT FOR T/C INPUT)
Single Strand wire gauge: Max 1.2mm (18SWG)
1
/ Din Size Instruments
16
1 1
/ & / Din Size Instruments
8 4
These diagrams show all possible option combinations. The actual
connections required depends on the exact model and options fitted.
CAUTION: Check information label on housing for correct operating
voltage before connecting supply to Power Input
Fuse: 100 – 240V ac – 1amp anti-surge
24/48V ac/dc – 315mA anti-surge
Note: At first power-up the message is displayed, as described in
section 6 of this manual. Access to other menus is denied until configuration
mode is completed
2. SELECT MODE
Select mode is used to access the configuration and operation menu functions.
B
It can be accessed at any time by holding down and pressing
In select mode, press or to choose the required mode, press
An unlock code is required to prevent unauthorised entry to Configuration, & Setup
modes. Press or to enter the unlock code, then press
Mode Upper Lower Description
Display Display
Operator Normal operation
Set Up Tailor settings to the application
Configuration Configure the instrument for use
Product Info Check manufacturing information
Note: The instrument will always return automatically to Operator mode if
there is no key activity for 2 minutes.
3. CONFIGURATION MODE
First select Configuration mode from Select mode (refer to section 2).
Press to scroll through the parameters, then press
value. Press to accept the change, otherwise parameter will revert to previous
value. To exit from Configuration mode, hold down and press
Select mode.
Note: Parameters displayed depends on how instrument has been configured.
Refer to user guide (available from your supplier) for further details.
Parameters marked * are repeated in Setup Mode.
Parameter Lower Upper Adjustment range & Description
Display Display
Input
See following table for possible codes
Range/Type
Code Input Type & Code Input Type & Code Input Type &
Range Range
L L L L C C C C
bC bC bC bC
B: 100 - 1824 ºC . L: 0.0 - 537.7 ºC
P24F P24F P24F P24F
L L L L F F F F
bF bF bF bF B: 211 - 3315 ºF L: 32.0 - 999.9 ºF
.
CC CC CC CC C: 0 - 2320 ºC NC NC NC NC N: 0 - 1399 ºC PTC PTC PTC PTC
CF CF CF CF C: 32 - 4208 ºF NF NF NF NF N: 32 - 2551 ºF PtF PtF PtF PtF
JC JC rC rC P P P P t t t t
JC JC J: –200 - 1200 ºC rC rC R: 0 - 1759 ºC
Pt Pt Pt Pt
JF JF JF JF J: –328 - 2192 ºF rF rF rF rF R: 32 - 3198 ºF
j j j j C C C C
J: –128.8 - 537.7 ºC SC SC SC SC S: 0 - 1762 ºC
.
j j j j F F F F
J: –199.9 - 999.9 ºF SF SF SF SF S: 32 - 3204 ºF
.
KC KC KC KC tC tC tC tC
K: –240 - 1373 ºC T: –240 - 400 ºC
KF KF KF KF K: –400 - 2503 ºF tF tF tF tF T: –400 - 752 ºF
k k k k C C C C t t t t C C C C
K: –128.8 - 537.7 ºC T: –128.8 - 400.0 ºC
. .
K K K K F F F F t t t t F F F F
K: –199.9 - 999.9 ºF T: –199.9 - 752.0 ºF
. .
LC LC LC LC
L: 0 - 762 ºC
PtRh20% vs. 40%:
P24C P24C P24C P24C
0 - 1850 ºC
LF LF
LF LF L: 32 - 1403 ºF
Note: Decimal point shown in table indicates temperature resolution of 0.1°
Parameter Lower Upper Adjustment range & Description
Display Display
Scale Range Scale Range Lower Limit +100
Upper Limit to Range Maximum
Scale Range Range Minimum to
Scale Range Upper Limit -100
Lower Limit
Decimal point =XXXX, =XXX.X, =XX.XX, =X.XXX
position
(non-temperature ranges only)
±Span of controller
Process Variable
Offset (see CAUTION note at end of section)
High Limit.
Limit relay is energised when
Limit Action process "safe" (PV < Limit Setpoint)
Low Limit.
Limit relay is energised when
process "safe" (PV > Limit Setpoint)
Setpoint Upper
Current Setpoint to Scale Range maximum
Limit
Setpoint Lower
Scale Range minimum to Current Setpoint
Limit
Process High Alarm
Process Low Alarm
Alarm 1Type Deviation Alarm
Band Alarm
No alarm
High Alarm 1
value* Scaled Range Minimum to
Low Alarm 1 scaled Range Maximum in display units
value*
Band Alarm 1
1 LSD to span from setpoint in display units
value*
Dev. Alarm 1
+/- Span from setpoint in display units
value*
Alarm 1
! ! ! !
1 LSD to full span in display units
Hysteresis*
Parameter Lower Upper
Display Display
Alarm 2 Type*
.
High Alarm 2
to enter.
value*
Low Alarm 2
to proceed.
value*
Default Band Alarm 2
value*
Unlock
Dev. Alarm 2
Codes
Value*
None
Alarm 2
! ! ! !
Hysteresis*
Mm Mm
Mm Mm
None
" " " "
# # # #
Output 2 Usage
or to set the required
, to return to
Default
Value
Linear Output 2
! ! ! !
Range
Range
Retransmit
PtRh20% vs 40%:
Output 2 Scale (display value at which output
32 - 3362 ºF
maximum
Retransmit
Pt100: –199 - 800 ºC
Output 3 Scale (display value at which output
Pt100: –328 - 1472 ºF
minimum
C C C C
Pt100: –128.8 - 537.7 ºC # # # #
. Output 3 Usage
F F F F Linear Output 3
Pt100: –199.9 - 999.9 ºF
.
! ! ! !
Range
0 - 20 mA DC
Retransmit
4 - 20 mA DC
Output 3 Scale (display value at which output
maximum
0 - 50 mV DC
Retransmit
. 10 - 50 mV DC
Output 3 Scale (display value at which output
0 - 5 V DC minimum
1 - 5 V DC
0 - 10 V DC Display Strategy $ $ $ $
2 - 10 V DC
% % % %
Default
Serial
Mm Mm Mm Mm
Value
Communications
Mm Mm
Mm Mm
Range max Protocol
Mm Mm Mm Mm
(Lin=1000)
Range min
.
(Linear=0)
Serial
.
Communications
.& & & &
Bit Rate
' ' ' ' .( ( ( (
' ' ' '.
Comms Address
1 to 255 (Modbus), 1 to 99 (ASCII)
Ww Ww Ww Ww
Comms Write
Configuration
) ) ) )
Lock Code
R/max Notes: Output 1 is always a Latching Limit Relay output.
If Option Slot A has the Digital Input module fitted, this always functions as a
Remote Reset, duplicating the function of the Reset) key
R/min
As these functions cannot be changed, no Configuration menus are required.
CAUTION: Process Variable Offset can be used to modify the
measured value to compensate for probe errors. Positive values
increase the reading, negative values are subtracted. This parameter
is effectively, a calibration adjustment and MUST be used with care.
There is no front panel indication of when this parameter is in use.
Range Max
Range Min
Adjustment range & Description Default
Value
Range Max
Range Min
Options as for alarm 1
Limit Output Relay
Alarm 1, Direct
Alarm 1, Reverse
Alarm 2, Direct
Alarm 2, Reverse
" " " "
Logical Alarm 1 OR 2, Direct
Logical Alarm 1 OR 2, Reverse
Logical Alarm 1 AND 2, Direct
Logical Alarm 1 AND 2, Reverse
Limit Annunciator, Direct
Limit Annunciator, Reverse
Retransmit Limit SP Output
Retransmit PV Output
0 to 5 V DC output 1
0 to 10 V DC output
2 to 10 V DC output
0 to 20 mA DC output
4 to 20 mA DC output
-1999 to 9999
Range max
will be maximum)
-1999 to 9999
Range min
will be minimum)
" " " "
As for output 2
As for output 2
-1999 to 9999
Range max
will be maximum)
-1999 to 9999
Range min
will be minimum)
PV is visible in Operator mode
PV not visible in Operator mode
Displays in Operator mode
when Limit Output is not active
ASCII
Modbus with no parity
Mm Mm Mm Mm
Modbus with Even Parity
Modbus with Odd Parity
1.2 kbps
2.4 kbps
.& & & &
4.8 kbps
9.6 kbps
19.2 kbps
Read/Write
Ww Ww
Ww Ww
Read only
0 to 9999
.