Dean Super Runner Series Service & Parts Manual page 40

2.5.1 Oil Drain Manifold, Drain Flush and Drain Valve Components (cont.)
ITEM PART #
1 823-3565
* 823-3566
2 812-1524
3 813-0784
4 813-0829
5 813-0748
6 200-1827
7 813-0659
8 809-0884
* 816-0544
9 813-0686
10 813-0165
11 813-0672
12 810-1669
13 810-1069
14 810-1668
15 106-1401
16 200-1617
17 210-2029
18 210-4727
* 823-3440
* 809-0885
* 809-0843
* 816-0547
19 807-2104
20 809-0842
21 816-0220
22 200-1257
23 810-2127
24 810-2052
* 810-2442
* 810-1338
* 210-3902
* 106-1417SP
* 813-0138
* 813-0716
* 813-0406
25 810-2126
* 812-1226SP
* 813-0392
* 812-1681
* 813-0870
* 813-0669
* Not Illustrated
Note: In Mar. 2003 SR42G went to 1" drain valves.
DEAN MILLIVOLT GAS FRYERS
CHAPTER 2: PARTS LIST
Elbow, with Bracket (LH)- 1-¼"- UFF 50
Elbow, with Bracket (RH)- 1-¼"- UFF 50
Drain Pipe, Left Side (Use 823-3418 for Chili's)
Drain Pipe, Right Side 1 ½" x 6"
Elbow, 1-½" NPT 75°
Tee, 1-½" NPT x 1-¼" BM With Handle Bracket
Drain Manifold Tube- 1-½" x 13-¼"
Pipe Cap, 1-½"
Nut, Slip Joint- 1-½"
O-ring (Slip-Joint Nut)
Bell Reducer, ½" NPT x 1-½"
Elbow, Street- ½" NPT 90°
Nipple, ½" NPT x 8" BM
Adapter, ⅝" O.D. x ½"- Female
Flex Line, ⅝" x 29-½ "
Adapter, ⅝" O.D. x ½"- Male
Drain Valve Components
Bracket, Microswitch (Optional On SUFF/UFF Units)
Washer, Drain Valve (Use Without Microswitch)
Bracket, Activator- Microswitch (Also Used On Valves Without Microswitch As A
Handle-Stop)
Handle (Actuator), Drain Valve
Handle, Push/Pull- Drain (With Cap)
Washer, ⅜" x 1" x .083"
Pin, Cotter
Cap, Vinyl-Red
Microswitch (Optional On SUFF/UFF Units)
Nut, Nylock- #4-40 (Microswitch To Bracket)
Insulation, Microswitch
Retainer, Nut
Drain Valve, 1-½" Full Port (With Washers & Nut)
Drain Valve, 1-¼" (1" Standard Port)
Handle, Valve Lever
Drain Valve, 1" SM20G, SR42G see note below
Handle, Valve Lever (For 810-1338 Only)- SM20G
Drain Valve Assembly 1" RH and LH
Nipple, 1" NPT x Close (To Adapt To 1-¼" Extended Drain Nipple)
Bushing, 1" NPT x 1-¼" BM (To Adapt To 1-¼" Extended Drain Nipple)
Coupling, 1-¼" NPT x 2" (To Adapt To 1-¼" Extended Drain Nipple)
Drain Valve, 1-¼" Full-Port (Use 106-2439 for Assembly)
Nipple, Drain- 1-¼" Painted- SM Series Fryers (use 813-0276 for SM20)
Nipple, Drain- 1-¼" NPT x 8" BM- All SR Series Fryers except SR42 w/ 1"
Nipple, Drain- 1-¼" x 5" NPT
Nipple, Drain- 1-¼" x 10" NPT
Nipple, Drain- 1" x 8" (Use 812-1668 for 5"-SR42) (Use 813-0605 for 9"- SR62)
COMPONENT
2-17