Related Manuals for Patton electronics 1088/I
Summary of Contents for Patton electronics 1088/I
- Page 1 USER MANUAL MODEL 1088/I 10BaseT mDSL Rocket Part# 07M1088I-UM SALES OFFICE Doc# 03311U2-001 (301)975-1000 Rev. D TECHNICAL SUPPORT Revised 10/24/06 (301)975-1007 An ISO-9001 http://www.patton.com Certified Company...
-
Page 2: Radio And Tv Interference
T T A A B B L L E E O O F F C C O O N N T T E E N N T T S S 1 1 . . 0 0 W W A A R R R R A A N N T T Y Y I I N N F F O O R R M M A A T T I I O O N N Patton Electronics warrants all Model 1088 components to be Section Page... - Page 3 LAN that has reached its maximum distance limits or separate high traffic areas of a LAN. The Rocket connects peered LANs and auto- matically forwards and receives LAN broadcasts, multi-casts and frames across a 2-Wire DSL span. The 1088/I supports PPP (RFC 1661) and BCP (RFC 1638). The NetLink...
-
Page 4: Ppp Operational Background
Patton 1088/I Router 3.0 PPP OPERATIONAL BACKGROUND Bridge PPP is a protocol used for multi-plexed transport over a point- Ethernet LAN to-point link. PPP operates on all full duplex media, and is a sym- metric peer-to-peer protocol, which can be broken into three main PEC Device w/ Serial I/F components: 1. -
Page 5: Netlink Plug-And-Play
4 4 . . 0 0 C C O O N N F F I I G G U U R R A A T T I I O O N N PTTs the ability to provision bandwidth on an as needed basis to cus- tomers. -
Page 6: Configuring The Hardware Dip Switches
4.2 CONFIGURING THE HARDWARE DIP SWITCHES 4.2.1 Configuration DIP Switch Set “S2” The Model 1088 has two sets of eight DIP switches, which allow configuration for a wide variety of applications. This section describes The only setting for S2 is for Clocking Mode between Model switch locations and explains all settings. - Page 7 4.2.2 Configuration DIP Switch Set “S3” Use the DIP Switches in Switch S3 to set the DTE Rate (for LAN Bandwidth Allocation), the transmit data sampling point and to reset the unit to its software default settings. The following table summa- rizes default positions of DIP Switch S3.
-
Page 8: Connecting 10Base-T Ethernet Port To Pc (Dte)
5 5 . . 0 0 I I N N S S T T A A L L L L A A T T I I O O N N 5.2 CONNECTING 10BASE-T ETHERNET PORT TO PC (DTE) The 10Base-T interface is configured as DTE (Data Terminal When the Model 1088 has been properly configured, it may be Equipment). -
Page 9: Power Connection
5.4 POWER CONNECTION 6 6 . . 0 0 O O P P E E R R A A T T I I O O N N Universal AC Power (100-240VAC) When the Model 1088 has been properly configured and installed, The Model 1088 uses a 5VDC, 2A universal input 100-240VAC, it should operate transparently. -
Page 10: Test Modes
6.4 TEST MODES 9 pulses = Detected LAN receive frame(s) too large The Model 1088 offers a proprietary Remote Loopback test modes, 10 pulses = Detected LAN receive frame(s) not plus a built-in V.52 BER test pattern generator to evaluate the communi- octet aligned cation status between units. - Page 11 transmitting data and the pattern generator is 6.4.2 Loops and Patterns enabled on one end of the link, the far end will begin receiving unframed packets and assume The following section describes the Remote Loopback/BER test that the line has gone down. During test modes, modes.
-
Page 12: Ethernet Specifications
If the above test indicates no errors are present, move the APPENDIX A test switch V.52 toggle switch UP, activating the “511/E” test with intentional errors present. If the test is working prop PATTON ELECTRONICS 10BASE-T MDSL ROCKET erly, the local unit’s red “ER” LED will blink. A successful SPECIFICATIONS “511/E”... - Page 13 PATTON ELECTRONICS MODEL 1088 FACTORY REPLACEMENT PARTS AND ACCESSORIES Patton Electronics Model # Description 1088/I ......10BaseT mDSL Rocket (CAP) 48V-PSM ......DC Power Supply Module 08055DCUI .....100-240VAC (+5V ±5% reg. DC/2A) Universal Input Adapter 0805EUR ......European Power Cord CEE 7 (“A”) 0805UK ......United Kingdom Power Cord (“D”)
Need help?
Do you have a question about the 1088/I and is the answer not in the manual?
Questions and answers