Subscribe to Our Youtube Channel
Related Manuals for Patton electronics 1040
Summary of Contents for Patton electronics 1040
- Page 1 USER MANUAL MODEL 1040 Self-Powered Universal Short Range Modem Part #07M1040-B SALES OFFICE Doc. #054011UB (301) 975-1000 Revised 4/29/98 TECHNICAL SUPPORT (301) 975-1007 An ISO-9001 http://www.patton.com Certified Company...
-
Page 2: Warranty Information
However, there is no guarantee that interference will not occur in a particular installation. If the Model 1040 does cause interference to radio or television reception, which can be... -
Page 3: General Information
The following instructions warranted for One Year parts and labor. If any questions or problems will help you set up and install the Model 1040 properly. If you have arise during installation or use of this product, please do not hesitate to any questions, don’t hesitate to call Patton Electronics Technical... -
Page 4: Configuration Switch Settings
SW1-1 through SW1-4: Data Rate Setting 3.2 CONFIGURATION SWITCH SETTINGS The Model 1040 has two sets of eight switches, yielding 16 total Switches SW1-1 through SW1-4 are set in combination to DIP switches. The two sets will be referred to as SW1 and SW2. As... - Page 5 SW2-1 and SW2-2 are set in combination to determine the word length for asynchronous/synchronous data. The setting for switch SW2-8 determines whether or not the Model 1040’s V.52 and V.54 tests will be enabled. To reset the V.54 circuit, set SW2-1 SW2-2 Setting switch SW2-8 to the “ON”...
-
Page 6: Installation
RJ-1 1 SIGNAL RJ-45 SIGNAL Once the Model 1040 is properly configured, it is ready to connect to your system. This section tells you how to connect the Model 1040 1....GND † 1 ....N/C to the twisted pair and RS-232 interfaces. - Page 7 Connect one pair of wires to the two XMT (transmit) poles on pry slot on the plastic case (below). Don't worry about the terminal block. The Model 1040 is not polarity sensitive, breaking the plastic, but make sure that you do not insert the so either wire may connect to either pole.
-
Page 8: Connection To The Rs-232 Interface
The Model 1040 is wired as a DCE, and therefore “wants” to plug into a DTE such as a terminal, PC or host. Because the Model 1040 is interface powered, a direct connection to the RS-232 DTE port is most desirable. -
Page 9: Led Status Monitors
These tests can be activated physically from the front panel, or via the RS-232 interface. 511/E RDL NORMAL Note: V.54 test modes on the Model 1040 are available for point-to- point and 4-wire applications only. Gaithersburg, Maryland MODEL 1040 Miniature Async./Sync. - Page 10 This requires two operators: one to initiate and monitor the test back to the user device. For example, characters typed on the at the local Model 1040, and one at the remote Model 1040. To use the keyboard of a terminal will appear on the terminal screen. To perform a V.52 BER test by itself, both operators should simultaneously follow...
- Page 11 PATTON MODEL 1040 CABLE RECOMMENDATIONS Transmission Format: Sync. or async., full or half duplex The Patton Model 1040 operates at frequencies of 20kHz or less Transmission Line: Unconditioned twisted pair 19 - 26 and has been performance tested by Patton technicians using twisted-...
- Page 12 APPENDIX C APPENDIX D PATTON MODEL 1040 PIN/SIGNAL ASSIGNMENTS PATTON MODEL 1040 BLOCK DIAGRAM DIRECTION “DCE” STANDARD SETTING DIRECTION 1- (FG) Frame Ground 2- (TD) Transmit Data To Model 1040 From Model 1040 Transmitting Clock - 15 3- (RD) Receive Data...
Need help?
Do you have a question about the 1040 and is the answer not in the manual?
Questions and answers