Related Manuals for Patton electronics 1089/I
Summary of Contents for Patton electronics 1089/I
- Page 1 USER MANUAL MODEL 1089/I 10BaseT HDSL Rocket Part# 07M1089I-UM SALES OFFICE Doc# 03207U2-001, (301)975-1000 Rev. D TECHNICAL SUPPORT Revised 10/25/06 (301)975-1007 An ISO-9001 http://www.patton.com Certified Company...
-
Page 2: Radio And Tv Interference
T T A A B B L L E E O O F F C C O O N N T T E E N N T T S S 1 1 . . 0 0 W W A A R R R R A A N N T T Y Y I I N N F F O O R R M M A A T T I I O O N N Patton Electronics warrants all Model 1089 components to be Section Page... - Page 3 LAN. The Rocket connects peered LANs and auto- matically forwards and receives LAN broadcasts, multi-casts and frames across a 2-Wire DSL span. The 1089/I is 802.3 compliant and supports PPP (RFC 1661) and BCP (RFC 1638).
-
Page 4: Ppp Operational Background
Patton 1089/I Router Bridge 3.0 PPP OPERATIONAL BACKGROUND PPP is a protocol used for multi-plexed transport over a point- Ethernet LAN to-point link. PPP operates on all full duplex media, and is a sym- PEC Device w/ Serial I/F metric peer-to-peer protocol, which can be broken into three main components: 1. -
Page 5: Configuring The Hardware Dip Switches
4 4 . . 0 0 C C O O N N F F I I G G U U R R A A T T I I O O N N 4.1.1 Configuration DIP Switch Set “S2” The Model 1089 has two sets of eight DIP switches, which allow configuration for a wide variety of applications. - Page 6 4.1.2 Configuration DIP Switch Set “S3” Use the DIP Switches in Switch S3 to set the DTE Rate (for LAN Bandwidth Allocation), the transmit data sampling point and to reset the unit to its software default settings. The following table summa- rizes default positions of DIP Switch S3.
-
Page 7: Connecting 10Base-T Ethernet Port To Pc (Dte)
5 5 . . 0 0 I I N N S S T T A A L L L L A A T T I I O O N N 5.2 CONNECTING 10BASE-T ETHERNET PORT TO PC (DTE) When the Model 1089 has been properly configured, it may be The 10Base-T interface is configured as DTE (Data Terminal connected to the DSL twisted pair interface, the 10BaseT Ethernet Equipment). -
Page 8: Power Connection
6 6 . . 0 0 O O P P E E R R A A T T I I O O N N 5.4 POWER CONNECTION When the Model 1089 has been properly configured and installed, Universal AC Power (100-240VAC) it should operate transparently. -
Page 9: Test Modes
8 pulses = Detected WAN receive frame(s) with CRC 6.4 TEST MODES 9 pulses = Detected LAN receive frame(s) too large 10 pulses = Detected LAN receive frame(s) not octet The Model 1089 offers a proprietary Remote Loopback test aligned modes, plus a built-in V.52 BER test pattern generator to evaluate the 11 pulses = Detected LAN receive frame(s) with bad communication status between units. - Page 10 (because it originates after the framer) and is intended to be evaluated only by another Restart Procedure The restart procedure is in place to allow the Processor. If the units are transmitting data and and Time Outs units to re-establish a connection after the the pattern generator is enabled on one end of framer begins seeing unframed packets.
- Page 11 If the above test indicates no errors are present, move the 6.4.2 Loops and Patterns test switch V.52 toggle switch UP, activating the “511/E” test with intentional errors present. If the test is working properly, The following section describes the Remote Loopback/BER test the local unit’s red “ER”...
- Page 12 Patton Electronics Model # Description Diagnostics: V52 compliant (511/511E) pattern generator and detector with error injection mode and 1089/I ......10BaseT mDSL Rocket (CAP) Remote Loopback control by a single front 48V-PSM ......DC Power Supply Module panel switch 08055DCUI .....100-240VAC (+5V ±5% reg. DC/2A)
- Page 13 APPENDIX C PATTON ELECTRONICS MODEL 1089 TRANSMISSION DISTANCE CHART Transmission Distance - Patton NetLink HDSL Model 1089 No Cross Talk Line Rate DTE Rates 26 AWG (0.4mm)24 AWG (0.5mm) kbps feet miles km feet miles km 64, 128 20700 3.9 6.2 24500 4.6 192, 256 17400 3.3...