Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Albatron PM915-478
Summary of Contents for Albatron PM915-478
- Page 1 PM915-478 Mainboard User’s Manual Rev：EG 1.1 Date：2009.1...
-
Page 2: Table Of Contents
CONTENTS CHAPTER 1 INTRODUCTION......2 Chipset Introduction ........2 Specification ..........2 Mainboard Introduction ........2 CHAPTER 2 PACKAGE CONTENTS......3 CHAPTER 3 MAINBOARD LOCATIONS..... 4 CHAPTER 4 INSTALLATION......5 Jumper Setting and Slot ........5 CHAPTER 5 BIOS SETUP......6 Main menu .......... -
Page 3: Chapter 1 Introduction
Chapter 1 Introduction 1.1 Chipset Introduction Intel 915GL Chipset The Intel 915GL chipset supports the latest PC technologies such as Socket 478 CPU, dual-channel DDR memory architecture and AGPe graphics card interface. Intel Graphics Media Accelerator 900 provides a significant increase in graphics performance.8 high-speed USB 2.0 ports. -
Page 4: Chapter 2 Package Contents
-Built-in Powerful Integrated Graphics Integrated display function technologies without extend VGA card Integrated 2D/3D Graphics Controller -Provides one channel connecting two IDE drives Supports Ultra ATA66/100 synchronous DMA modes -Provides four channel connecting four SATA drives With speed up to 150MB/s -I/O ：... -
Page 5: Chapter 3 Mainboard Locations
Chapter 3 Mainboard Locations... -
Page 6: Chapter 4 Installation
Chapter 4 Installation 4.1 Jumper Setting and Slot Clear CMOS Jumper setting 1-2（Default） Normal Clear CMOS Audio：Front panel Jumper setting Function Function MIC+ Ground Vbias AuD_Vcc(AVCC) AuD_R_Out R_Out Back N.C. AuD_L_Out L_Out Back SATA：PIN Jumper setting SATA1 Function SATA3 Function Ground Ground RSATA_RXP1... -
Page 7: Chapter 5 Bios Setup
Connectors PS/2（Bottom） PS/2 Keyboard (Purple) PS/2（Top） PS/2 Mouse Header(Green) R_USB1 USB1/2 Connector Port F_USB2/LAN USB3/4/LAN Connector Port F_USB3 USB5/6 Connector Port F_USB4 USB7/8 Connector Port Printer Connector Port COM1 Serial Port COM1 Connector Port On-board VGA connector LINE OUT/LINE IN/MIC Audio Output/Audio Input/Microphone SPDIF_I/ SPDIF_O Digital Input/Output Port... -
Page 8: Main Menu
has stored the configuration information; or you can hold down the Page Up key while rebooting your computer. Holding down the Page Up key also clears the setup information 5.1 Main menu You can use cursor arrow keys to highlight anyone of options on the main menu page. -
Page 9: Standard Cmos Features
Load Fail-Safe Defaults Setup the default values in system Load Optimized Defaults Setup the best performance values in system Set Supervisor Password Setup supervisor password in system Set User Password Setup user password in system Save & Exit Setup Setup save and exit, press Y to save and exit Exit Without Save Setup Setup without save and exit, press N to without save and exit 5.2 Standard CMOS Features... -
Page 10: Advanced Bios Features
Base Memory Expanded Memory Total Memory 5.3 Advanced BIOS Features CPU Feature Default：Press Enter Delay Prior to Thermal Default: 16Min Thermal Management Default: Thermal Monitor 1 Limit CPUID MaxVal Default: Disabled C1E Function Default: Auto Execute Disable Bit Default: Enabled Removable Device Priority Default: Press Enter Floppy Disks... -
Page 11: Advanced Chipset Features
If you enable this item, the system will also search for other boot devices if it fails to find an operating system from the first two locations. Swap Floppy Drive Default：Disabled If you have two diskette drives installed and you enable this item, drive A becomes drive B and drive B becomes drive A. -
Page 12: Integrated Peripherals
Video BIOS Cacheable Default：Disabled Memory Hole At 15M-16M Default：Disabled PCI Express Root port Function Default: Press Enter PCI Express port 1 Default: Auto PCI Express port 2 Default: Auto PCI Express port 3 Default: Auto PCI Express port 4 Default: Auto PCI Express port 5 Default: Auto PCI Express port 6... - Page 13 *** On-Chip Serial ATA Setting *** X SATA Mode Default：IDE On-chip serial ATA Default: Auto X SATA PORT Speed Settings Default: Disabled PATA IDE Mode Default：Primary SATA Port Default: p1,p3 IS Secondary Onboard Device Default: Press Enter USB Controller Default：Enabled USB 2.0 Controller Default：Enabled USB Keyboard Support...
-
Page 14: Power Management Setup
POWER ON Function Default: BUTTON ONLY X KB Power ON Password Default: Enter X Hot Key Power ON Default: Ctrl-F1 Onboard FDC Controller Setup onboard FDC controller Default: Enabled Onboard Serial Port 1/2 Setup onboard serial port1/2 Default： 3F8/IRQ4/2F8/IRQ4 UART Mode Select Setup UART mode select Default：Normal UR2 Duplex Mode... -
Page 15: Set Sueprvisor Password &Set User Password
Wake-up by PCI card Default：Disabled Power On by Ring Default: Disabled Resume by Alarm Default：Disabled Date (of Month) Alarm Default：0 Time (hh:mm:ss) Alarm Default：0 ** Reload Global Timer Events ** Primary/ Secondary IDE 0/1 Default：Disabled FDD,COM,LPT Port Default：Disabled PCI PIRQ [A-D]# Default: Disabled 5.7 Set Supervisor Password &Set User Password If you highlight this item and press Enter, a dialog box appears that...
Need help?
Do you have a question about the PM915-478 and is the answer not in the manual?
Questions and answers