Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Intergraph TDZ 2000 GL1
Summary of Contents for Intergraph TDZ 2000 GL1
- Page 1 TDZ 2000 GL1/ExtremeZ GL1 System Reference July 1998 DHA027210...
- Page 2 Notice Information in this document is subject to change without notice and should not be considered a commitment by Intergraph Computer Systems. Intergraph Computer Systems shall not be liable for technical or editorial errors in, or omissions from, this document. Intergraph Computer Systems shall not be liable for incidental or consequential damages resulting from the furnishing or use of this document.
- Page 3 Notes Read all safety and operating instructions before using the equipment. Keep these instructions for future reference. Follow all warnings on the equipment or in the operating instructions. This device is designed and manufactured to comply with approved safety standards for information processing and business equipment.
-
Page 5: Table Of Contents
About This Document....................ix Document Conventions....................ix Customer Support ......................x Hardware and Software Support Services ............x World Wide Web .....................x Intergraph Bulletin Board Service ..............x FAXLink......................xi Telephone ...................... xi More Support Options ..................xi 1 Accessing the System....................1 Tools ..........................2 Protecting Against Electrostatic Discharge ..............2... - Page 6 Adding Expansion Cards .....................33 Slot Locations ....................34 Installing Expansion Cards ................34 Assigning System Resources ................35 Adding Drives and Devices..................35 Device Locations....................36 Adding External SCSI Drives ..................37 SCSI Cable Length Guidelines ...............37 SCSI Cable Quality Guidelines...............38 SCSI ID Guidelines..................38 SCSI Termination Guidelines for External Devices ........38 Connecting the Device ...................39 Changing SCSI Adapter or Device Settings ............39 4 System Hardware Overview and Specifications............41...
- Page 7 Floppy Disk Drive..................68 4.0 GB and 9.0 GB Disk Drives ..............68 7 Power Supply and Cooling Fans................71 Power Supply.......................72 Power Supply Cable Routing................73 P1 Pinout .......................73 P2 - P5 Pinouts....................73 P6 Pinout .......................73 Cooling Fans .......................74 Index...........................75...
- Page 8 viii...
-
Page 9: Introduction
This System Reference provides information necessary to service and upgrade a TDZ 2000 GL1 or ExtremeZ GL1 system. For information on how to set up the system for use, refer to the TDZ 2000 GL1/ExtremeZ GL1 System Setup guide. About This Document This document is organized as follows: Chapter 1, “Accessing the System,”... -
Page 10: Customer Support
On these pages, you can get news and product information, technical support information, software updates and fixes, and more. Intergraph Bulletin Board Service On the Intergraph Bulletin Board Service (IBBS), you can get technical support information, software updates and fixes, and more. To connect to the IBBS: 1. -
Page 11: Faxlink
In the United States, call 1-800-633-7248 between the hours of 7:00 a.m. and 7:00 p.m. Central Time, Monday through Friday (except holidays). Outside the United States, contact your local Intergraph Computer Systems subsidiary or distributor. Have the following information available when you call: Your service number, which identifies your site to Intergraph Computer Systems. - Page 12 For software support questions in the United States, call 1-800-345-4856. Outside the United States, contact your local Intergraph Computer Systems subsidiary or distributor.
-
Page 13: Accessing The System
Accessing the System This chapter lists hand tools and describes servicing restrictions, methods for avoiding electrostatic discharge, and how to remove and attach cover panels from a TDZ 2000 GL1 or ExtremeZ GL1 workstation. This system features a chassis architecture designed to make upgrades and expansion simple. -
Page 14: Tools
No. 1 and No. 2 Phillips screwdrivers Small or medium flat-blade standard screwdriver You do not need any tools to open the TDZ 2000 GL1/ExtremeZ GL1 case. Protecting Against Electrostatic Discharge Electrostatic discharge (ESD) can damage sensitive components inside the unit. Take the... - Page 15 NOTE Removing the right side panel is necessary only for servicing internal bay disk drives, the plastic cowling on the right panel, or the face panel. To open the case: 1. Grasp the lip on the top cover at the rear of the system and press up on the release. See the following figure.
-
Page 16: System Illustrations
System Illustrations The front, left view below shows major parts of the system without covers, cables, system board and option cards. - Page 17 The back, left view below shows the chassis with all major components removed.
-
Page 19: Servicing The System
Servicing the System This chapter describes how to replace the standard parts within a TDZ 2000 GL1 or ExtremeZ GL1 system. Obey all warning and caution labels while replacing parts. Note that internal parts servicing procedures assume you have removed the left side panel from the system. -
Page 20: Case Components
Case Components Ordinarily you will not need to replace any of the external case components unless they are broken or cosmetically damaged. All case components are designed for durability, but the item that may require replacement first is the door and hinge assembly. To replace the hinge or door, you must first remove the top cover. - Page 21 7. Do both of the following on the underside of the door: Spread the release tabs on the large emblem and remove it Squeeze the release tabs on the small emblem and remove it 8. Slide the hinge toward the front of the chassis until it stops. 9.
- Page 22 7. Orient the new hinge rail the same way as the one you removed, place the tabs in the slots, and press outward until the rail snaps into place. 8. From the front of the chassis, slide the hinge into the rails. To replace the face panel: 1.
-
Page 23: Peripheral Drives
8. Turn the face panel downward until the power switch button drops out. 9. Place the left side of the new face panel near the left, front of the chassis and orient the switch so that the black and green wires are at the bottom. 10. -
Page 24: Cd-Rom Drive
CD-ROM mounting screws Floppy drive mounting screws 3. From inside the chassis, push the back of the floppy drive until the bezel clears the chassis, and slide the device out. 4. Slide the new floppy drive into the chassis and align the mounting holes. 5. -
Page 25: External Bay Disk Drives
Mounting guide 5. Note the jumper settings on the rear of the CD-ROM. 6. Set the master/slave jumper to the same position as the old drive. 7. Install the mounting guide on the right side of the new CD-ROM. 8. Slide the new CD-ROM drive into the chassis and align the mounting holes. 9. - Page 26 External bay mounting screws 3. From inside the chassis, push the tray out of the external bay, grasp the front of the tray, and then slide it out of the bay. 4. Remove the screws that secure the disk drive to the tray and remove the drive. 5.
-
Page 27: Internal Bay Disk Drives
Mounting guide Drive tray Access hole (2) 7. Slide the tray assembly into the chassis and align the mounting holes. 8. Install the screws that secure the tray to the chassis. 9. Connect the SCSI cable and the power cable to the disk drive. Internal Bay Disk Drives To replace an internal bay disk drive: 1. - Page 28 6. Do one of the following: If installing an EIDE drive, set the master/slave jumper setting on the new drive to match that of the old drive If installing a SCSI drive, set the SCSI ID on the new drive to match that of the old drive.
-
Page 29: Power Supply
8. Insert the alignment tabs into the appropriate slots in the chassis. Screw holes for front mounting tabs 9. Install the two screws that secure the drive bracket assembly front mounting tabs to the chassis. 10. Install the screw that secures the drive bracket assembly to the right side of the chassis. 11. -
Page 30: Processor Modules
9. Plug the AC power cord into its connector on the back of the chassis. Processor Modules The TDZ 2000 GL1 and ExtremeZ GL1 systems are designed to support 266, 300, and 333 MHz Pentium II processors. See the system board diagram in Chapter 5, “System Board,”... - Page 31 Heat-sink lock 2. Press the locking tabs on the top corners of the processor module inward, towards each other, until they click into the release position. 3. Slide the processor module out of the retension module. 4. Remove the new processor from its antistatic package, and align the processor module over the retension module.
-
Page 32: Heat-Sink Mounting Brackets
Heat-Sink Mounting Brackets Pentium II processors equipped with heat-sink fins use heat-sink locks fastened to mounting brackets to secure them to the system board, providing additional stability to the processor module. See the system board diagram in Chapter 5, “System Board,” for connector and socket locations. -
Page 33: Simms
To replace a retension module: 1. Remove the processor module. See the “Processor Modules” section above for details. 2. Remove the heat-sink locks, if necessary. See the “Heat-Sink Mounting Brackets” section above for details. 3. Remove the screws securing the retension module to the system board, and remove the retension module. -
Page 34: System Board
Push in this direction to Locked module lock into place Empty socket 7. When you restart the computer, the BIOS detects the new memory automatically. System Board You must swap the SIMMs and processor module(s) from the old system board to the new one if you replace the system board. - Page 35 Hole in right side of chassis Fastex fastener To remove the system board: 1. Lay the chassis down on its right side. 2. Note the locations where all cables are connected to the system board. 3. Disconnect all cables from the system board. 4.
-
Page 36: Expansion Cards
7. Connect the internal cables to the system board. If you need help identifying cable connections, see Chapter 5, “System Board.” Expansion Cards See the system board diagram in Chapter 5, “System Board,” for connector and socket locations. To replace an expansion card: 1. -
Page 37: Lithium (Cmos/Clock) Battery
After you install the new battery, you must reset the date and time and reconfigure the BIOS. See the TDZ 2000 GL1/ExtremeZ GL1 System Setup for details on updating and configuring the BIOS. WARNING There is a danger of explosion if the battery is incorrectly replaced. -
Page 38: Leds, Light Pipe, And Power Switch
WARNING Replace the battery with the same or equivalent type only, as recommended by the battery manufacturer. Dispose of used batteries according to the battery manufacturer’s instructions. To replace the battery: 1. Remove any expansion cards that restrict access to the battery. See the “Expansion Cards”... - Page 39 3. Disconnect the LEDs from the light pipe. Power LED (black/white wires) Top of chassis Disk activity LED (black/orange wires) 4. Squeeze the mounting tabs on the light pipe inward and push the light pipe through its mounting hole. 5. From inside the chassis, remove the light pipe. 6.
-
Page 41: Upgrading The System
Upgrading the System This chapter describes upgrading memory and processors, as well as installing expansion cards, internal SCSI drives, and external SCSI drives in your TDZ 2000 GL1 or ExtremeZ GL1 system. NOTE See Chapter 1, “Accessing the System,” for instructions on opening the system and protecting against electrostatic discharge. -
Page 42: Adding Memory
SIMM. 64 MB Memory Modules On a TDZ 2000 GL1 or ExtremeZ GL1, 64 MB SIMMs built with 16-Mbit DRAM memory do not work reliably. A system that uses these SIMMs can fail to boot or to operate properly. -
Page 43: Memory Configurations
Memory Configurations The following tables shows possible memory configurations. Each bank contains one socket. Memory size SIMM Configuration (non-ECC) 16 MB 4 x 32 32 MB 8 x 32 64 MB 16 x 32 Bank 0 Bank 1 Bank 2 Bank 3 Memory SIMMs... -
Page 44: Adding A Processor
After completing the hardware upgrade, you must also upgrade to a multi-processor version of Windows NT. You can upgrade the operating system in the following ways: You can purchase the Intergraph upgrade kit mentioned previously. The kit contains all the hardware, software, and documentation required to perform the upgrade. -
Page 45: Adding Expansion Cards
The system BIOS detects the board’s presence during startup and reads information from the board’s configuration registers to assign the necessary system resources. All PCI expansion cards sold by Intergraph fully comply with the Peripheral Component NOTE Interconnect Specification, 2.1. -
Page 46: Slot Locations
Slot Locations The expansion slots are located at the bottom, left section of the system board, as shown in the following figure. Slot 5 is a shared PCI/ISA slot. You can install a card in the number 5 PCI slot or the number 1 ISA slot, but not in both. PCI Slot 1 PCI Slot 2 PCI Slot 3... -
Page 47: Assigning System Resources
Other expansion cards do not include a diskette, but require that you manually program the BIOS with the configuration information. See Chapter 4, “Configuring the BIOS,” in the TDZ 2000 GL1/ExtremeZ GL1 System Setup for details on assigning system resources and configuring the BIOS for expansion cards. -
Page 48: Device Locations
When installing 5.25-inch peripheral devices, use the screws provided in the package found in the Accessory Box. See the following chapters for related information and important details: Chapter 5, “System Board,” for details on SCSI connector locations and pinouts. Chapter 6, “Peripherals,” for details on drive locations, jumpers, and cables. Chapter 7, “Power Supply, Fans, and Hardware Monitoring Devices,”... -
Page 49: Adding External Scsi Drives
CD-ROM drive—Location 7 Floppy disk drive—Location 6 Add-on drive—Location 5 Add-on drive—Location 4 Add-on drive—Location 3 Add-on drive—Location 2 System drive—Location 1 See Chapter 2, “Servicing the System,” to install a memory upgrade. Adding External SCSI Drives You can add single-ended external SCSI drives to the system by connecting them to an optional SCSI adapter. -
Page 50: Scsi Cable Quality Guidelines
SCSI Cable Quality Guidelines To ensure data integrity and optimum performance, do the following: Use only Intergraph SCSI cables. Cables from other vendors may not provide adequate shielding. Use the shortest cables possible to connect SCSI devices to the system and to each other. -
Page 51: Connecting The Device
Connecting the Device If your system has an optional SCSI adapter card installed, you can connect external SCSI devices to the adapter’s external SCSI port. To add an external SCSI device: 1. Connect one end of the external SCSI cable to the external port of the SCSI adapter: 2. -
Page 53: System Hardware Overview And Specifications
System Hardware Overview and Specifications This chapter contains general, technical information about the hardware in a TDZ 2000 GL1 or ExtremeZ GL1 system. Hardware Overview .....................42 Functional Diagram .....................43 System Board.......................44 System Configuration Summary...................44 System Model Number....................45 Specifications.......................47 Hardware Monitoring ....................47... -
Page 54: Hardware Overview
Hardware Overview The following figure shows the major parts and assemblies inside the server. Power Supply with Fan CD-ROM Drive Floppy Disk Drive Chassis Disk Drives (5.25 inch) Disk Drives System Board... -
Page 55: Functional Diagram
Functional Diagram The following diagram shows the power and data signals of the base unit components. Power AC In Data Power and Data Power Supply System Board Speaker Floppy Disk Drive Keyboard Mouse Monitor AC In CD-ROM Drive Serial Ports Parallel Port Disk Drives... -
Page 56: System Board
System Board The following table lists the main chip components on the system board. Component Description Form Factor System BIOS American Megatrends BIOS Processor(s) Intel Pentium II; 266, 300, or 333 MHz, SEC (Single Edge Connector) Chipset Intel 440 FX series (Natoma) Host-to-PCI Bridge Intel SB82371SB Combo Controller... -
Page 57: System Model Number
The model number on the unit identifies the system hardware and software configuration. The following table defines the individual digits. Digit Meaning 1: Series TDZ 2000 GL1/ExtremeZ GL1 2: Processor Type No processor Single Intel Pentium II, 300 MHz, 512 KB cache Dual Intel Pentium II, 300 MHz, 512 KB cache... - Page 58 Digit Meaning Dual Intel Pentium II, 266 MHz, 512 KB cache 3. Graphics No graphics Intense 3D 2200 Matrox Millennium II w/4MB Matrox Millennium II w/8MB Accel AccelSTAR II w/8MB RealiZm II ZX25 4: Chassis Workstation ExtremeZ With sound card With sound card and network card With sound card, network card, and ZIP drive EIDE with sound card...
-
Page 59: Specifications
Fan speed Low battery voltage alert Chassis intrusion security alert See Chapter 2 in the TDZ 2000 GL1/ExtremeZ GL1 System Setup for details on InterSite Hardware Monitor. Refer to the TDZ 2000 GL1/ExtremeZ GL1 System Setup for information about using the... -
Page 60: Optional Hardware
Optional Hardware If your system includes any of the following hardware, see the documentation delivered with that hardware for additional information: Monitor SCSI CD-Recorder (CD-R) drive Internal/external SCSI disk drive Removable SCSI disk drive PCI SCSI adapter PCI network adapter SCM SwapBox PC card adapter Iomega Zip or Jaz drive TR-4 tape drive... -
Page 61: System Board
System Board This chapter provides cable and jumper connector information, major component descriptions, memory subsystem details and addresses, and external port pinouts for the system board. Major Features......................50 Connectors, Slots, and Sockets..................51 Connectors........................52 Jumper Functions......................54 Jumper Settings ......................54 Processor and Bus Speed................54 DRAM Voltage Select..................54 I/O Select .......................55 LM78 IRQ Select ...................55... -
Page 62: Major Features
Major Features The following figure shows the location of major features on the system board. Power Primary connector SIMM sockets Secondary Lithium battery Floppy disk drive connector PCI slots Primary IDE connector ISA slots Secondary IDE connector... -
Page 63: Connectors, Slots, And Sockets
Connectors, Slots, and Sockets The following figure shows the location of connectors, slots, sockets, and other features on the system board. -
Page 64: Connectors
Connectors The following tables lists important connector information. Connector Cable Connects To Keyboard Mouse Forward chassis fan (not included) Secondary processor fan (not included) Universal Serial Bus Primary processor fan (not included) J29:pins 1, 2 MCBL250AB Power switch J29: pins 8- 10 Not included IR Homing device (not included) - Page 65 CON 6, 7 - MCBL121A, EIDE Data Cable Pinout Signal Signal Signal BRSTDRV- D01+(1) Ground D01+(14) DOAK0- D01+(7) D01+(0) Ground D01+(8) D01+(15) IRQ14 D01+(6) Ground IOCS16- D01+(9) — D01+(5) D0RQ0- — D01+(10) Ground D01+(4) DOIOW- D01+(11) Ground CS1P- D01+(3) D0IOR- CS3P- D01+(12) Ground...
-
Page 66: Jumper Functions
Jumper Functions The following tables lists important system board jumpers. Jumper Function J11, J12, J37 Bus speed J13-J16, J24-J27 DRAM voltage select J30, J36 I/O select J31-J34 Processor frequency CMOS & password reset J49, J50 LM78 IRQ select Flash EPROM select (pins 1-2 5V, pins 2-3 12V) Jumper Settings The following tables show the settings for various jumper connectors. -
Page 67: I/O Select
I/O Select Closed Open Closed Open Open Closed Open Closed LM78 IRQ Select Open Open Open Open CMOS and Password Reset Jumper Normal Clear (Reset) Open Closed... -
Page 68: External Ports And Pinouts
External Ports and Pinouts The following figure shows the external ports on the back of the unit. AC power connector AC voltage switch 115/230 V Mouse Keyboard Serial Parallel (COM) Line in Game/MIDI Line out Microphone Video out... - Page 69 Keyboard, Mouse The keyboard and mouse ports are PS/2 style, 6-pin ports. They are not interchangeable. Signal KDATA (keyboard) MDATA (mouse) Spare Ground KCLK Spare Serial The serial ports (also referred to as RS-232 asynchronous communications ports, or COM ports) connect modems, printers, peripherals, and other computers to the system.
- Page 70 Parallel The parallel port is used almost exclusively for printers, but is compatible with any peripheral device designed to interface with a standard Centronics-type parallel port. Use only shielded cables with the parallel port (DB-25). Signal Signal -Strobe -ACK - Acknowledge Data 0 Busy Data 1...
- Page 71 Audio Line In The Audio Line In port connects audio input devices, such as a tape deck or a CD player, to the computer. Signal Ground Left Channel In Right Channel In Microphone The Microphone port connects the microphone jack of the NMB multimedia keyboard to the computer.
- Page 72 Game/MIDI The Game/MIDI port connects a game joystick or a MIDI device, such as a musical keyboard or synthesizer, to the system. Signal Signal Fire button 0 Fire button 2 X-axis, X-axis, joystick 2 joystick 1 Ground MIDI out Ground Y-axis, joystick 2 Y-axis, Fire button 3...
-
Page 73: Pci To Isa Bus Interrupt Mapping
PCI to ISA Bus Interrupt Mapping The ISA bridge provides the sixteen conventional ISA interrupts, plus four interrupt request pins for PCI peripheral interrupts (PIRQ0 through PIRQ3). For PC-AT architecture compatibility reasons, the PCI interrupts are routed to the ISA interrupts within the ISA bridge. -
Page 75: Peripherals
Peripherals This chapter provides information on the cabling and configuration of common peripherals within a TDZ 2000 GL1/ExtremeZ GL1 system. Peripheral Cables ......................64 EIDE Cable Connection Locations ..............64 Floppy Cable Connection Locations ...............64 Peripheral Configuration ....................65 EIDE CD-ROM Drive..................65 SCSI CD-Recorder..................66 Iomega Jaz 1 GB Internal SCSI Drive ............67... -
Page 76: Peripheral Cables
Peripheral Cables This section provides information on peripheral cables and associated connections. See the section, “Cable Routing and Pinouts,” in Chapter 5, “System Board,” for additional details. Cable illustrations are not to scale. You can identify the cables and connectors using their spacing as reference. -
Page 77: Peripheral Configuration
Peripheral Configuration This section provides illustrations and information on configuring common peripherals for the system. See the following for related information: Chapter 5, “System Board,” for cable connector locations and pinouts. Chapter 7, “Power Supply, Fans, and Hardware Monitoring Devices,” for power cable information and pinouts. -
Page 78: Scsi Cd-Recorder
SCSI CD-Recorder The following figure shows the back of the CD-recorder. Audio connector SCSI connector Term Power jumper Power Termination jumper connector Parity Enable jumper Device Connector Connects to Audio (analog) Audio cable connector on sound card Power Power supply SCSI SCSI connector on SCSI adapter To disable SCSI termination, remove the Termination jumper and the Term Power jumper. -
Page 79: Iomega Jaz 1 Gb Internal Scsi Drive
Iomega Jaz 1 GB Internal SCSI Drive The following figure shows the jumpers on the bottom of the drive. Front Power connector SCSI connector Device Connector Connects to Power Power supply SCSI SCSI connector on SCSI adapter The drive is not terminated and requires external termination only if installed as the last device on the SCSI chain. -
Page 80: Floppy Disk Drive
Floppy Disk Drive The following figure shows the cable connectors on the back of the floppy disk drive. Data cable Power connector connector Device Connector Connects to Power Power supply Data Floppy disk drive controller on system board 4.0 GB and 9.0 GB Disk Drives You can use either of the following Wide Ultra SCSI disk drives in the system: Part Number Vendor... - Page 81 oooooooo oooooooo SCSI connector Pin 1 Power connector Device Connector Connects to Power Power supply SCSI SCSI connector on SCSI adapter To disable SCSI termination, remove the TE jumper from connector J2. To enable parity, remove the PD jumper from connector J2. For optimum performance, remove all jumpers from J2.
-
Page 83: Power Supply And Cooling Fans
Power Supply and Cooling Fans This chapter describes the 250-watt power supply, power-related pinouts, cooling fans, and hardware monitoring devices. Power Supply.......................72 Power Supply Cable Routing................73 P1 Pinout .......................73 P2 - P5 Pinouts....................73 P6 Pinout .......................73 Cooling Fans .......................74... -
Page 84: Power Supply
Power Supply The TDZ 2000 GL1 and ExtremeZ GL1 power supply is a 250-watt manual-ranging supply. It switches between 90-132 VAC or 180-264 VAC, depending on the range setting. The input frequency is 47-63 Hz, single phase. At full load, the power supply has a minimum efficiency of 65 percent. -
Page 85: Power Supply Cable Routing
Power Supply Cable Routing The following table lists the cable connectors from the power supply that connect to the system board and other devices. Connector Connects to Notes J6 on system board P2, P3, P4, P5 Hard disk drive/CD-ROM Chassis fan Via cable MCBL173A Floppy disk drive P1 Pinout... -
Page 86: Cooling Fans
Cooling Fans The TDZ 2000 GL1/ExtremeZ GL1 has three cooling fans. One is inside the power supply; the others are mounted in the chassis. All fans are 12 VDC. The fans pressurize the chassis and force warm air out from the vents. Hardware controls the dynamic speed of each four- wire fan. -
Page 87: Index
Index Connectors, 52 Conventions document, ix 250W power supply, 72 DC output specifications AC safety interlock power supply, 72 function of, 2 Diagram of external ports, 56 Airflow direction and fan rotation, DIMMs installation rules, 30 Assigning resources for option replacing, 21 cards, 35 Document... - Page 88 Host bridge, 44 voltages and functions, 47 Mouse port pinout, 57 ID guidelines for SCSI devices, 38 Installing an option card, 34 Intergraph Non-compliant PCI option cards, BBS, x Internal bay disk drives replacing, 15 Internal SCSI drives Opening case for service, 3...
- Page 89 P2-P5 pinouts face panel, 10 power supply connector, 73 hinge rails, 9 P6 pinout Replacing power supply connector, 73 CD-ROM drive, 12 Parallel port DIMMs, 21 pinout, 58 door assembly, 8 PCI option cards, 33 external bay disk drives, 13 PCI to ISA bus interrupt mapping, fans, 24 floppy disk drive, 11...
- Page 90 Standby switch photo, 50 replacing, 26 replacing, 22 system System Configuration Utility BIOS, 44 assigning system resources for configuration summary, 44 option cards, 35 funtional diagram, 43 System fans, 74 hardware overview, 42 System resources hardware overview and assigning, 35 specifications, 41 illustrations, 4 maintenance...
Need help?
Do you have a question about the TDZ 2000 GL1 and is the answer not in the manual?
Questions and answers