1. Manuals
  2. Brands
  3. SPALDING Manuals
  4. Fitness Equipment
  5. M880961
  6. Owner's manual

SPALDING M880961 Owner's Manual

In-ground basketball system
Hide thumbs
Table of Contents

Advertisement

Quick Links

WARNING!
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO
PROPERTY.
Toll-Free Customer Service Number for U.S: 1-800-558-5234 Canada Only: 1-800-284-8339
© COPYRIGHT 2006 by SPALDING
In-Ground Basketball System

Owners Manual

Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
• 3 Capable Adults
• Carpenter's Level
• 15' Tape Measure
• Sh ovel & Post Hole
Digger
• Phillips Screwdriver
• (1) Utility Knife
Internet Address: http://www.hydra-rib.com

REQUIRED TOOLS AND MATERIALS:

• (2) Stepladders 8 ft. (2.4 m)
• Safety Goggles
• (2 each) Wrenches and/or Socket Wrenches and
Sockets (Deep-Well Sockets are Recommended).
3/8"
1/2"
3/8"
1/2"
1
Write Model Number
From Box Here:
9/16"
3/4"
15/16"
9/16"
3/4"
15/16"
02/06
•
• Container to Mix
• Optional: Large &
Small Adjustable
Wrenches
ID# M880961

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the M880961 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for SPALDING M880961

Summary of Contents for SPALDING M880961

  • Page 1: Owners Manual

    OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO 3/8" 1/2" 9/16" 3/4" 15/16" PROPERTY. • (1) Utility Knife Toll-Free Customer Service Number for U.S: 1-800-558-5234 Canada Only: 1-800-284-8339 Internet Address: http://www.hydra-rib.com © COPYRIGHT 2006 by SPALDING 02/06 ID# M880961...

  • Page 2: Safety Instructions

    The American Basketball Council website at http://www.smarthoops.com. In the U.S.: 1-800-558-5234 In the U.S.: 1-888-713-5488 In Canada: 1-800-284-8339 ID#: 588000 05/05 WARRANTY CARD: Please remember to complete your product registration form either on-line at: www.huffysports.com/customer_support/product_registration or mail-in the enclosed postcard. ID# M880961 02/06...
  • Page 3 Install threaded ends of J-bolts (1) through holes in mounting plate (3) and secure as shown. NOTE: Nuts on the top of plate are used for leveling the pole after system is fully assembled. 02/06 ID# M880961...
  • Page 4 WARNING! DO NOT PROCEED UNTIL CONCRETE HAS CURED! A MINIMUM OF 72 HOURS. ALLOW ADDITIONAL TIME FOR COLD, WET OR HUMID WEATHER. IMPORTANT! Check leveling of mounting plate several times with carpenter’s level while concrete is curing. ID# M880961 02/06...
  • Page 5 (2). IMPORTANT! Holes in pole must be parallel with playing surface. PLAYING SURFACE Secure pole (5) flange to mounting plate (3) as shown. Tighten completely. NOTE: Position crank jack mounting as shown. 02/06 ID# M880961...
  • Page 6 (9) as shown. THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR IMPORTANT! PROPERTY DAMAGE. Do Not Over Tighten. IMPORTANT! Bushing types are identified with a letter. ID# M880961 02/06...
  • Page 7 Secure backboard to support arms (8 and 9) as IMPORTANT! shown. Bushing types are identified with a letter. IMPORTANT! Do Not Over Tighten. 02/06 ID# M880961...

  • Page 8: Rear View

    NOTE: Position U-joint of crank jack (20) as shown. Where tubes on crank jack join, hold steady to keep both tubes from rotating. Rotate handle clockwise on crank jack to the fully extended position. IMPORTANT! Hold Here. ID# M880961 02/06...
  • Page 9 TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. IMPORTANT! Bushing types are identified with a letter. 28 13 13 28 REAR VIEW IMPORTANT! Do Not Over Tighten. 02/06 ID# M880961...
  • Page 10 REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. REAR VIEW NOTE: Some adjustment will be necessary to align the lower crank jack and bushings to jack brackets (21). ID# M880961 02/06...
  • Page 11 7 8 9 10 Attach height indicators (16) to lower arm in areas as IMPORTANT! shown by turning screws (17) into place with a phillips screwdriver. Note Orientation of Height Indicators: 10’ Mark Should Face Away From Backboard. 02/06 ID# M880961...
  • Page 12 Rim Assembly Remove rim cover prior to installing rim assembly to board. IMPORTANT! Refer To Instructions Carefully cut and peel Included With Rim protective film away from Hardware For Rim board prior to attaching rim. Assembly. ID# M880961 02/06...
  • Page 13 If adjustment is necessary, adjust system by rotating the nuts (2) between mounting plate (3) and pole flange. Apply height adjustment label (31) to front of pole as shown. HR83008PoleGusset REGULATION RIM HEIGHT IS 10 FEET (3.05 m). 02/06 ID# M880961...

  • Page 14: Height Adjustment

    Pole pad may NOT be included in this model. MHE19.EPS 206239 Height Adjustment Rotate crank handle to raise or lower backboard. NOTE: If height adjustment is difficult to operate, you may have over tightened the areas indicated. M83013.E 211560 M83014.EPS ID# M880961 02/06 211560...

  • Page 15: Parts List

    * You May Have Extra Parts With This Model. Item Qty. Part No. Description HARDWARE IDENTIFIER (BOLTS) Item #24 (2) Item #17 (4) Item #10 (4) Item #23 (2) #206271 hex head bolt,1/2 x 2 1/2 Item #11 (3) Item #33 (1) 02/06 ID# M880961...
  • Page 16 Item #13 (20) Item #14 (11) Item #7 (2) Item #25 (6) Item #22 (4) HARDWARE IDENTIFIER (PLASTIC & NYLON SPACERS) Item #15 (2) Item #28 (20) Item #27 (8) * You May Have Extra Parts With This Model. ID# M880961 02/06...

Table of Contents