Sensor Weight Bar Installation - ProSpot Fitness P-100 Owner's Manual

o_
7 .
9 .
L
Plug together both of the Base Rail Wire Harness (8) to lower ends of the Spiral Signal Cables (46) located
just under the perforated Slider Shields on back of the Screen Panels (53).
Attach the two Rear Support Rails (4) to the Lower Cross Brace (3) and the Cross Brace Backing Plates (13)
using four bolts (28), eight washers (18) and four nuts (20) as shown. HAND TIGHTEN the bolts at this time.
Attach the two Big Pulleys (27) to the two Upper Linking Plates (17) using two bolts (19), four washers (23)
and two nuts (26) as shown. HAND TIGHTEN the bolts at this time.
Lift the Upper Linking Plates Assembly (17 & 271 and place it on top of the Left Upright Guidepost Assembly
(9, 12, 53), and attach the two Upper Linking Plates (17) to the Left Upright Guide Post (12) using two bolts
(22), four washers (18) and two nuts (20) as shown. HAND TIGHTEN the bolts at this time.
'10. Carefully flex the Left Weight Bar Cables (24) onto the pulleys (27) so that the cables insert into the grooves
of each corresponding pulleys and allowing the Left Weight Bar Knuckle (44) to hang free. Be sure that the
cables are straight and uncrossed and cables and pulleys move smoothly.
1 1. Align the holes on top of the Rear Support Rail (4) with the corresponding holes on the two Upper Linking
Plates ('17) and attach the Rear Support Rail (4) to the Linking Plates (17) using two bolts (22), four washers
(18) and two nuts (20) as shown. HAND TIGHTEN the bolts at this time.
12. Repeat the steps 8 - 1 1 on the right side of the PROSPOTT/rressrM
P-'l00.
13. Attach the Upper Cross Brace (11)to the four Upper linking Plates (17) using four bolts (22), eight washers
(18) and four nuts (20) as shown. HAND TIGHTEN the bolts at this time.
14. Tighten all bolts and nuts used for assembly in previous steps.
STEP #2: SENSOR WEIGHT BAR INSTALLATION
1. Standing in front of the PROSPOTlaessrM P-100. Insert one end and then the other end of the Sensor
Weight Bar (25) into the Knuckles (42 & 44). Slide the knuckles onto the Bar untrl they rest snugly against
the preinstalled sensor retaining collars (45 & 48) at each end of the Sensor Weight Bar (25). (There is a
rotation limiting pin that protrudes from the bottom of the Sensor Weight Bar (25) that must fit through a slot
in the knuckles U2 & 44\ as it is slid into position).
2.
Place one Plastic Locking Sleeve (39) onto each end of the Sensor Weight Bar (25) and slide them inwards
until they butt up against and secure the Weight Bar Cable Knuckle in place. Tighten Plastic Locking Sleeve
bolts securely.
3.
Place one of the Olympic Adapters (30) onto the Sensor Weight Bar (25) and slide them onto the Bar until
they touch the Plastic Locking Sleeves (39). lnsert an Olympic Adapter Retaining Plug (33) onto each end
of the Sensor Weight Bar (25) so that they also go inside of the Olympic Adapters (30). Secure with two
Allen bolts (29) and two washers (36).
4.
Attach the four small plastic pipes (15) to the four Upper linking Plates (17) using four bolts (34), eight
washers (38) and four nuts (35) as shown. Tighten the bolts securely.
5.
Attach the Electronic Box Locating Board (40) to the Lower Cross Brace (3) using two bolts (22), tour
washers (18) and two nuts (20) as shown. Tighten the bolts securely.
6.
Attach the six Side Weight Plate Holders (14) to the Rear Support Rails (4) using six backing plates (16),
twelve bolts (22), twenty-four washers (18) and twelve nuts (20) as shown. Tighten the bolts securely.
Note: In this manual when referring to Left and Right side of unit, the left and right perspective
are from the outside, facing the front of the unit.
--2--