Table of Contents
Advertisement
Available languages
Available languages
Installation
Instructions
INSTALLING THE WATER LINE
BEFORE YOU BEGIN
Recommended copper water supply kits are WXSX2,WXSX3
or WXSX4,depending on the amount of tubing you need, Approved
plastic water supply lines are GESmartConnectT= Refrigerator
Tubing (WX08X10006,WX08X10015 and WX08X10025),
When connecting your refrigerator to a GEReverseOsmosis Water
System, the only approved installation is with a GERVKit,For other
reverse osmosis water systems, follow the manufacturer's
recommendations,
This water line installation is not warranted by the refrigerator
or icemaker manufacturer, Follow these instructions carefully
to minimize the risk of expensive water damage,
Water hammer (water banging in the pipes)in house plumbing can
cause damage to refrigerator parts and lead to water leakage or
flooding, Call a qualified plumber to correct water hammer before
installing the water supply line to the refrigerator,
To prevent burns and product damage, do not hook up the water
line to the hot water line,
Ifyou use your refrigerator before connecting the water line, make
sure the feeler arm is in the STOP(up)position,
Do not install the icemaker tubing in areas where temperatures fall
below freezing,
When using any electrical device (such as a power drill) during
installation, be sure the device is double insulated or grounded in a
manner to prevent the hazard of electric shock, or is battery
powered,
All installations must be in accordance with local plumbing
code requirements,
WHAT YOU WILL NEED
• Copper or GESmartConnect '= Refrigerator Tubing kit,
1/4" outer diameter to connect the refrigerator to the water
supply, If using copper, be sure both ends of the tubing are
cut square,
To determine how much tubing you need: Measure the distance
from the water valve on the back of the refrigerator to the water
supply pipe,Then add 8¢ (2,4m), Be sure there is sufficient extra
tubing (about 8¢ [2,4 m] coiled into 3 turns of about 10" [25 cm]
diameter) to allow the refrigerator to move out from the wall after
installation,
GESmartConnecC Refrigerator Tubing Kitsare available in the
following lengths:
6' (1,8 m)
- WX08X10006
15' (4,6m)
- WX08X10015
25' (7,6m)
- WX08X10025
Be sure that the kit you select allows at least 8' (2,4m) as described
above,
NOTE:The only GEapproved plastic tubing is that supplied
in GESmartConnect T= Refrigerator Tubing kits. Do not use any
other plastic water supply line because the line is under pressure
at all times. Certain types of plastic will crack or rupture with age
and cause water damage to your home.
(ON SOME MODELS)
WHAT YOU WILL NEED (CONT.)
. AGE water
supply
kit (containing
tubing, shutoff valve
and fittings
listed below) is available
at extra cost from
your dealer or from Parts and Accessories,
1,8OO,661,1616,
. A cold water
supply,
The water
pressure must be
between
20 and 120 p,s,i, (1,4-8,1 bar),
, Power drill.
,1/2"
or adjustable
wrench.
, Straight
and Phillips
blade screwdriver.
. Two 1/4" outer diameter
compression
nuts and
2 ferrules
(sleeves)--to
connect the copper tubing
to the shutoff valve and the refrigerator
water valve,
OR
. If you are using a OE SmartConnect
T=Refrigerator
Tubing kit, the necessary
fittings
are preassembled
to the tubing,
. If your existing copper water line has a flared fitting
at
the end, you will need an adapter
(available
at
plumbing
supply stores) to connect the water
line to
the refrigerator
OR you can cut off the flared fitting
with a tube cutter
and then use a compression
fitting,
Do not cut formed end from GE SmartConnect
T=
Refrigerator
tubing,
. Shutoff valve to connect to the cold water
line,
The shutoff valve should have a water inlet with a
minimum
inside diameter
of 5/32" at the point of
connection
to the COLD WATER LINE, Saddle-type
shutoff valves are included in many water
supply kits,
Before purchasing,
make sure a saddle-type
valve
complies
with your local plumbing
codes,
11
Advertisement
Table of Contents
