Changing A Cycle Or Setting; Adding Items During A Cycle; Option Selections; Cycle Status Indicators - Kenmore ULTRA WASH 665.1735 Series Use & Care Manual

During the first minute of a cycle
1. Select a new cycle and/or options.
2. Check the detergent dispensers. They must be filled properly
for the new cycle.
3. Make sure the door is closed. The dishwasher resumes the
new cycle and/or option after a 5-second pause.
2.
3.
4.
5.
After the first minute of a cycle
1. Press CANCEL. The Cancel light glows. Your dishwasher
starts a 2-minute drain (if needed). Let the dishwasher drain
completely.
Check the detergent dispensers, They must be filled properly
for the new cycle.
Make sure the door is closed.
Select a new cycle and/or options.
Press START.
You can add an item anytime before the main wash starts. Open
the door and check the detergent dispenser. If the cover is still
closed, you can add items.
To add items
1. Carefully open the door slightly to stop the cycle, Wait for the
spraying action to stop before opening the door.
2. Open the door. If the detergent dispenser cover is still closed,
add the item.
3. Close the door firmly until it latches. The dishwasher resumes
the cycle after about a 5-second pause.
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn the option off,
or select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
any time before drying begins.
Press START to use the same cycle and option(s) as the previous
wash cycle.
NOTE: If the last cycle you completed was a rinse cycle, when
you press Start, the dishwasher runs the last full wash cycle and
options.
Hi Temp Wash
Select this option to increase the water temperature during the
wash portions of the cycle. Hi Temp Wash raises the water
temperature to 145°F (63°C), in the main wash. Heating the water
helps improve washing results. Hi Temp Wash is useful when
loads contain baked-on food.
This option adds heat, wash time and may add water to the
cycle.
NOTE: Hi Temp Wash is an option with the Pots Pans and
Normal Wash cycles.
Air Dry
Select this option to dry without heat. Air drying is useful when
loads contain plastic dinnerware that may be sensitive to high
temperatures.
The dishes take longer to dry and some spotting can occur. For
best drying, use a liquid rinse aid. Some items (such as plastics)
may need towel drying.
NOTE: Air Dry is an option with all cycles, except Quick Rinse.
Lock On
Use the Lock On to prevent unintended use of the dishwasher.
You can also use the lock feature to prevent unintended cycle or
option changes during a cycle.
When LOCK ON is lit, all buttons are disabled.
NOTE: The dishwasher door can be opened while the controls
are locked.
To turn on the Lock
Press and hold AIR DRY for 4 seconds. LOCK ON glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times.
To turn off the Lock
Press and hold AIR DRY for 4 seconds. The light turns off.
Delay Hours
Select this option to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay countdown. After adding items, firmly close the door until it
latches. The delay will not continue if the door is not latched.
To delay the start
1. Press DELAY HOURS until the desired number of 2, 4, or
8 hours is lit.
2. Select a wash cycle and options.
3. Press START.
The selected Delay Hours light glows. The dishwasher starts the
cycle in the selected number of hours.
NOTES:
• To cancel the delay and cycle, press CANCEL.
• To cancel the delay and start the cycle, press DELAY HOURS
until no lights glow. Then press DELAY HOURS one more
time. The delay indicator turns off, and the delayed cycle
starts.
Follow the progress of your dishwasher with the Cycle Status
indicators.
O WASHING
@ SENSING
@ DRYING
@ CLEAN
Sensing
Your dishwasher senses the soil level on the dishes. Soil level
determines the length of some cycles, the amount of heat added
to the wash or rinse, and the cycle needed for the load. SENSING
glows during the soil sensing parts of the cycle. Wash action
continues while sensing occurs.
Clean
Clean glows when a cycle is finished, The light turns off when you
press any button or close the door.
12