Craftsman 315.218291 Operator's Manual page 52

_. CRAFTSMAN 10 in. TABLE SAW - MODEL NO. 315.218291 ._
I The model number will be found on a label attached to the side panel of the cabinet. Always mention the model number in all correspondence /
regarding your TABLE SAW or when ordering repair parts.
J
KEY PART
NO. NUMBER
1 089110122707
2 089110122016
3 089110122015
4 089110122014
5 089110122013
6 089110122705
7 089110122703
8 0182011804
9 0182010214
10 0182010213
11 089110122001
12 089110122906
13 089110122005
14 0182010216-127
15 410011708
16 0182010207
17 412011065
18 410171705
19 0181010814
20 0182010302-129
21 0182010303-129
22 0181010815
23 089110122003
24 0181010804
25 0181010401
26 422010044
27 0181010503
28 0181010504
29 089110122006
30 410141702
31 A182012002
32 0181010823
33 0131010222-130
34 0181010314
35 089110122002
PARTS LIST (FIGURE A)
KEY PART
DESCRiPTiON QTY
Miter Table Assembly .................................................. 1
Hex Nut (M6 x 4.8 mm) ................................................ 2
Washer (6.5 x 13 x lt) .................................................. 1
Lock Lever ................................................................... 5
Clamp Plate ................................................................. 2
Bracket Assembly ........................................................ 1
Blade Guard Assembly ................................................ 1
Rear Rail ....................................................................... 1
End Cap R2 (Left Rear) ............................................... 1
End Cap R1 (Right Rear) ............................................. 1
Saw Table ..................................................................... 1
Support Warning Label ................................................ 1
Throat Plate .................................................................. 1
Align-A-Cut Insert ........................................................ 1
Screw (5/16-18 x 3/4 in., Hex Hd.) ............................... 4
Rail Locking Clamp ...................................................... 4
Washer (8 x 16 x 0.8t) .................................................. 4
Screw (10-24 x 5/16 in., Pan Hd.) ................................ 2
Screw (10-24 x 1/2 in.) ................................................. 4
Rear Cabinet Panel ...................................................... 1
Left Cabinet Panel ....................................................... 1
Screw (8-32 x 3/8 in., Special) ................................... 12
Dust Cover ................................................................... 1
Hex Nut (5/8-18) ........................................................... 1
Blade Washer ............................................................... 2
Blade (10 in. x 36t) ....................................................... 1
1/4 in. Spacer .............................................................. 1
1/2 in. Spacer ............................................................... 1
Guide Holder ................................................................ 1
Screw (8-32 x 3/4 in., Pan Hd.) .................................... 2
Accessory Table Assembly
(Inc. Key Nos. 52 & 57-64) ........................................... 1
Screw w/Washer (10-24, Pan Hd. Special) .................. 4
Power Cord Holder ...................................................... 2
Shim (0.5 mm) .............................................................. 2
Locker Bracket ............................................................. 1
NO. NUMBER
36 0181010323
37 0181010317
38 424010003
39 0181010310
40 0181010214
41 411011707
42 412011743
43 410011714
44 A182010101
45 0182010304-129
46 411011008
47 0181010816
48 0182010701
49 410451703
50 0301030202
51 0181010230
52 0182010102-126
53 451050005
54 0181010231
55 A182010901
56 0181010831
57 410151704
58 0182010208
59 0181010601
60 412011063
61 413051004
62 0181010309
63 0181010211
64 411072702
65 0181010606
66 0181010105
67 414011014
68 410191005
69 410171707
70 0181010905
71 0181010312
DESCRI PTION QTY
Clamp Plate ................................................................. 2
Rail Holder Nut ............................................................. 4
V Belt (106H9 Bando) ................................................... 2
Shim ............................................................................. 2
Spacer .......................................................................... 1
Hex Nut (1/4-20) ........................................................... 2
Washer (6.5 x 25 x 1.6t) ............................................... 1
Screw (1/4-20 x 1 in., Hex Hd.) .................................... 1
Motor Assembly ........................................................... 1
Right Cabinet Panel ..................................................... 1
Hex Nut (8-32) .............................................................. 3
Grounding Screw (8-32 x 3/4 in.) ................................. 1
Power Cord (14 AWG x 3.3 M) ..................................... 1
Screw (8-16 x 3/4 in.) ................................................... 5
Clamp (5/16 in.) ............................................................ 1
Right Plug Socket Box ................................................. 1
Accessory Table ........................................................... 1
Outlet ........................................................................... 1
Left Plug Socket Box ................................................... 1
Rip Fence Assembly (See Figure C)............................. 1
Screw (8-32 x 1/2 in., Pan Hd) ..................................... 2
Screw (1/4-20 x 3/4 in., Hex Soc. Hd.) ........................ 1
Accessory Table Lever ................................................. 1
Lever Shaft ................................................................... 1
Washer (12 x 22 x lt) ................................................... 1
"E" Ring ........................................................................ 1
Spring Plate ................................................................. 1
Back-Up Plate .............................................................. 1
Lock Nut (1/4-20) ......................................................... 1
Shaft ............................................................................. 1
Bevel Gear ................................................................... 2
Roll Pin (M4 x 30 mm) .................................................. 2
Screw (M4 x 20 mm, Truss Hd.) ................................... 4
Screw (10-24 x 5/8 in., Pan Hd.) .................................. 4
Needle Roller ................................................................ 2
Pivot Plate .................................................................... 2
52