10 in. compound miter saw double insulated (41 pages)
Summary of Contents for Craftsman 315.212300
Page 1
Safety Rules and Operating • Adjustments Instructions before first use of • Operation this product. • Maintenance Customer Help Line: 1-800-932-3188 • Parts List Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.sears.com/craftsman NRTL/C 972000-507 3-01...
TABLE OF CONTENTS Table of Contents ............................2 Warranty and Introduction ..........................2 Rules For Safe Operation ........................... 3-6 Glossary ..............................6-7 Product Specifications and Unpacking ......................7 Labels ................................8 Loose Parts and Tools Needed ........................9 Features ..............................10-12 Adjustments .............................
RULES FOR SAFE OPERATION The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.
Page 4
RULES FOR SAFE OPERATION (Continued) USE THE PROPER EXTENSION CORD. Make function. Check for alignment of moving parts, sure your extension cord is in good condition. binding of moving parts, breakage of parts, When using an extension cord, be sure to use mounting and any other conditions that may one heavy enough to carry the current your affect its operation.
Page 5
Lock the miter table by securely tightening the WARNING: When servicing use only identical miter lock handle. Lock the saw arm (bevel Craftsman replacement parts. Use of any other function) by securely tightening the bevel lock parts may create a hazard or cause product knob.
RULES FOR SAFE OPERATION (Continued) ALWAYS STAY ALERT! Do not allow familiarity MAKE SURE THE WORK AREA HAS AMPLE (gained from frequent use of your saw) to cause LIGHTING to see the work and that no obstruc- a careless mistake. ALWAYS REMEMBER that tions will interfere with safe operation BEFORE a careless fraction of a second is sufficient to performing any work using your saw.
GLOSSARY OF TERMS FOR WOODWORKING (Continued) No Hands Zone Through Sawing The area between the marked lines on the left and Any cutting operation where the blade extends right side of the miter table base. This zone is completely through the thickness of the workpiece. identified by no hands zone labels placed inside the Workpiece marked lines on the miter table base.
10 inch Compound Miter Saw DOUBLE INSULATED 5,000 RPM 120 VOLTS 60 Hz AC ONLY 15 A WARNING: WHEN SERVICING, USE ONLY IDENTICAL CRAFTSMAN REPLACEMENT PARTS. MODEL 315.212300 SER. NO. MADE IN TAIWAN NRTL/C SEARS, ROEBUCK AND CO.
LOOSE PARTS LIST The following items are included with your Compound Miter Saw: Saw Blade - 10 in. 5 mm Hex Key Miter Lock Handle 6 mm Hex Key Dust Guide 8 mm Hex Key Blade Wrench Owner's Manual BLADE WRENCH SAW BLADE 8 mm HEX KEY...
FEATURES KNOW YOUR COMPOUND MITER CUTTING CAPACITIES ° When the miter angle (miter table) is set at 0 ° See Figure 3. the bevel angle is set at 0 Before attempting to use your saw, familiarize yourself Your saw will cut materials up to a maximum of with all operating features and safety requirements.
Page 11
FEATURES CARRYING HANDLE SPINDLE LOCK BUTTON See Figure 4. See Figure 5. For convenience when carrying or transporting your A spindle lock button has been provided for locking miter saw from one place to another, a carrying the spindle which keeps the blade in your saw from handle has been provided on top of the saw arm as rotating.
Page 12
FEATURES POSITIVE STOPS ON MITER TABLE 7” 10” 3-3/4” Positive stops have been provided at 0°, 22-1/2° and 45°. The 22-1/2° and 45° positive stops have been 4-5/8” provided on both the left and right side of the miter table. BEVEL LOCK KNOB 18”...
ADJUSTMENTS WARNING: To prevent accidental starting that TO INSTALL BLADE could cause possible serious personal injury, See Figures 10, 11, and 12. assemble all parts to your saw before connecting it to power supply. Saw should never be WARNING: A 10 in. blade is the maximum connected to power supply when you are blade capacity of your saw.
Page 14
ADJUSTMENTS LOWER PHILLIPS Wipe a drop of oil onto inner blade washer and BLADE GUARD SCREW outer blade washer where they contact the blade. WARNING: If inner blade washer has been removed, replace it before placing blade on spindle. Failure to do so could cause an accident since blade will not tighten properly.
Page 15
ADJUSTMENTS Note: Many of the illustrations in this manual show FENCE MITER TABLE only portions of your compound miter saw. This is intentional so that we can clearly show points being made in the illustrations. Never operate your saw without all guards securely in place and in good operating condition.
Page 16
ADJUSTMENTS Rotate the mounting bracket left or right until the SQUARING THE SAW BLADE TO THE saw blade is parallel with the square. FENCE Retighten the screws securely and recheck the See Figures 17 - 20. blade-to-fence alignment. Unplug your saw. FENCE WARNING : Failure to unplug your saw could...
Page 17
ADJUSTMENTS SQUARING THE BLADE TO THE If the top or bottom of the saw blade angles away from the square as shown in figures 22 and 23, MITER TABLE adjustments are needed. See Figures 21-24. Unplug your saw. FENCE WARNING : Failure to unplug your saw could result in accidental starting causing possible serious personal injury.
Page 18
ADJUSTMENTS Retighten bevel lock knob. Next, retighten lock nut PIVOT ADJUSTMENTS securing the positive stop adjustment screw. Note: These adjustments were made at the factory Recheck blade-to-table alignment. and normally do not require readjustment. Note: The above procedure can be used to check TRAVEL PIVOT ADJUSTMENT blade squareness of the saw blade to the miter table at both 0°...
ADJUSTMENTS DEPTH STOP WARNING: Before starting any cutting ADJUSTMENT operation, clamp or bolt your compound miter SCREW saw to a workbench. Never operate your miter saw on the floor or in a crouched position. Failure to heed this warning can result in serious personal injury.
OPERATION Slowly lower the blade into and through the workpiece. See Figure 26. Release the switch trigger and allow the saw blade to stop rotating before raising the blade out STRAIGHT of workpiece. Wait until the electric brake stops CROSSCUT blade from turning before removing the workpiece from the miter table.
Page 21
OPERATION WARNING: To avoid serious personal injury, keep your hands outside the no hands zone; at BEVEL CUT least 3 in. from blade. Never perform any cutting operation freehand (without holding workpiece against the fence). The blade could grab the workpiece if it slips or twists.
Page 22
OPERATION TO MAKE A COMPOUND CUT WITH Recheck miter angle setting. Make a test cut in scrap material. YOUR MITER SAW: Place the workpiece flat on the miter table with Pull out the lock pin and lift saw arm to its full one edge securely against the fence.
Page 23
OPERATION Before turning on the saw, perform a dry run of the cutting operation just to make sure that no problems will occur when the cut is made. Grasp the saw handle firmly, press the lock-off tab down, then squeeze the switch trigger. Allow sev- eral seconds for the blade to reach maximum speed.
Page 24
OPERATION CUTTING COMPOUND MITERS To aid in making the correct settings, the compound angle setting chart below has been provided. Since com- pound cuts are the most difficult to accurately obtain, trial cuts should be made in scrap material, and much thought and planning made, prior to making your required cut.
Page 25
OPERATION CUTTING CROWN MOLDING LAYING MOLDING FLAT ON THE MITER TABLE Your compound miter saw does an excellent job of See Figure 32. cutting crown molding. In general, compound miter saws do a better job of cutting crown molding than To use this method for accurately cutting crown any other tool made.
Page 26
OPERATION When cutting crown molding by this method the bevel angle should be set at 33.85°. The miter angle should be set at 31.62° either right or left, depending on the desired cut for the application. See the chart below for correct angle settings and correct positioning of crown molding on miter table.
WARNING: EXTENSION CORDS When servicing, use only identical Craftsman replacement parts. Use of any other The use of any extension cord will cause some loss of part may create a hazard or cause product power. To keep the loss to a minimum and to prevent damage.
MAINTENANCE WARNING: To ensure safety and reliability, all Your saw has externally accessible brush assemblies repairs — with the exception of the externally that should be periodically checked for wear. accessible brushes — should be performed by a Proceed as follows when replacement is required: qualified service technician at a Sears store to Unplug your saw.
CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212300 Figure A...
Page 31
CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212300 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your CRAFTSMAN COMPOUND MITER SAW or when ordering repair parts.
Page 32
CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212300 Figure B...
Page 33
CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212300 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your COMPOUND MITER SAW or when ordering repair parts.
Page 34
CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.235360 CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.235360 CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212300 Figure C...
Page 35
CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212300 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your COMPOUND MITER SAW or when ordering repair parts.
Page 36
CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212300 SEE NOTE “A” Figure D...
Page 37
CRAFTSMAN COMPOUND MITER SAW - MODEL NUMBER 315.212300 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your CRAFTSMAN COMPOUND MITER SAW or when ordering repair parts.
Get it fixed, at your home or ours! For repair of major brand appliances in your own home… no matter who made it, no matter who sold it! 1-800-4-MY-HOME Anytime, day or night (1-800-469-4663) www.sears.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts &...
Need help?
Do you have a question about the 315.212300 and is the answer not in the manual?
Questions and answers