3/8 in. cordless drill-driver variable speed / reversible (18 pages)
Summary of Contents for Craftsman 315.101531
Page 1
To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Customer Help Line: 1-800-932-3188 °® Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 Visit the Craftsman web page: www.sears.com/craftsman 983000-398 9-03...
Parts Ordering / Service ............................... FULL ONE YEAR WARRANTY ON CRAFTSMAN 3/8-in. CORDLESS RIGHT ANGLE DRILL-DRIVER If this £RAFTSMn# tool fails to give complete satisfaction within one year from the date of purchase, RETURN IT TO THE NEAREST SEARS STORE OR SEARS SERVICE CENTER IN THE UNITED STATES, and Sears wilt repair it, free of charge.
Page 3
• Do not overreach. Keep proper footing and balance WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions at all times. Proper footing and balance enable better control of the tool in unexpected situations. listed below, may result in electric shock, fire and/or serious personal injury.
SERVICE • When servicing a tool, use only identical replace- ment parts. Follow instructions in the Maintenance • Tool service must be performed only by qualified section of this manual. Use of unauthorized parts or repair personnel. Service or maintenance performed failure to follow Maintenance Instructions may create a by unqualified personnel could result in a risk of injury.
Page 5
chemicals that can damage, weaken, or destroy WARNING: Read and understand all instruc- plastic. tions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious • An extension cord should not be used unless absolutely personal injury.
Page 6
Important:Someofthefollowing symbols maybeusedonthistool.Please studythemandlearn theirmeaning. Proper interpretation ofthesesymbols willallowyoutooperate thetootbetter andsafer. SYMBOL NAME DESIGNATION/EXPLANATION Volts Voltage Amperes Current Hertz Frequency (cycles per second) Watt Power Minutes Time "X., Alternating Current Type of current "-"= Direct Current Type or a characteristic of current No Load Speed Rotational speed, at no load Class II Construction...
SPECIFICATIONS Chuck ................................3/8 in., Keyless Motor .................................. 14.4 Volt DC Switch ................................Variable Speed No Load Speed ..............................0-800/rain. Charger Input ............................120 V, 60 Hz, AC only Charge Rate ................................. 1 Hour Torque ..................................140 in.lb. _Craftsman EX101531- 14.4V testcriter!a "_ in.lb, torque...
Page 8
BATTERYPACK KEYLESS SHOWNIN CHUCK CHARGER HARGER REDLED ON INDICATES DIRECTION OF FASTCHARGING MODE ROTATION SELECTOR GREENLED ONAFTER (FORWARD/ FASTCHARGING REVERSE/LOCK /_--_"_ -_'_-"_---_" CYCLE,INDICATES OFF) ,N R,OKLE CHARGE =ODE YELLOW GREEN SWITCH DISCHARGED OR DEFECTIVEBATTERY STORAGE PACK WRIST SCREWDRIVER STRAP_ 4-1/2in, _v"...
Page 9
LED FUNCTIONS OF CHARGER WARNING: Do not allow familiarity with the tool to LED WILL BE ON TO INDICATE STATUS make you careless. Remember that a careless fraction of a second is sufficient to inflict severe CHARGER AND BATTERY PACK: injury.
Page 10
SWITCH REVERSIBLE See Figure 2. See Figure 2. To turn the drill ON, depress the switch trigger. To turn it This direction of rotation is reversible and is controlled by OFF, release the switch trigger. a selector located above the switch trigger. With the drill held in normal operating position, the direction of rotation selector should be positioned to the left of the switch for WARNING:...
Page 11
INSTALLING BITS See Figure 4. • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 2. • Open or close the chuck jaws to a point where the opening is slightly larger than the bit size you intend to use.
Page 12
TO INSTALL BATTERY PACK • Make sure the latches on each side of the battery pack snap into place and the battery pack is secured in the • Lock the switch trigger on the drill by placing the drill before beginning operation. direction of rotation selector in the center position.
Page 13
DRILLING WARNING: Be prepared for binding or bit See Figure 8. breakthrough. When these situations occur, drill has a tendency to grab and kick opposite to the direction of rotation and could cause loss of control when WARNING: Always wear safety goggles or safety breaking through material.
Page 14
CHUCK REMOVAL • Insert the hex key in chuck and tighten the chuck jaws securely. Tap sharply with a mallet in a counterclock- See Figures 9, 10, and 11. wise direction. This will loosen the chuck on the spindle. The chuck must be removed in order to use some It can now be unscrewed by hand.
Page 15
WARNING: When servicing, use only identical to be repaired or replaced by the customer. All other parts Craftsman replacement parts. Use of any other part should be replaced at a Sears Service Center. may create a hazard or cause product damage.
CRAFTSMAN 14.4 VOLT CORDLESS DRILL-DRIVER MODEL NO. 315.101531 SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS PARTS LIST Number Description Qty. 6612003 Chuck Screw ..............6903302 Chuck ................. 1325101 * Battery Pack (Item No. 9 11044) ........1425301 * Charger (Item No. 9 11041) ..........
Page 18
Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters.