Craftsman 315.101540 Operator's Manual

3/8 in. 19.2 volt cordless right angle drill-driver variable speed/reversible

Advertisement

Quick Links

3/8 in. 19.2 VOLT CORDLESS
RIGHT ANGLE DRILL-DRIVER
SPEED/REVERSmBLE
VARIABLE
Model No.
315.101540
WARNING:
To reduce the risk of injury,
the user must read and understand the
operator's manual before using this
product.
_q
/
¢
Customer
HeUp Line: 1-800-932-3188
Sears, Roebuck
and Co., 3333 Bevedy Rd., Hoffman
Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com!craftsman
983000-511
7-04
Save this manual
for future
reference

Advertisement

Table of Contents
loading

Summary of Contents for Craftsman 315.101540

  • Page 1 Customer HeUp Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Bevedy Rd., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.sears.com!craftsman Save this manual for future reference 983000-511 7-04...
  • Page 2: One Year Full Warranty

    NEAREST SEARS STORE OR SEARS PARTS & REPAIR CENTER IN THE UNITED STATES, and Sears wil! repair it, free of charge. Hfthis Craftsman too! is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.
  • Page 3: Personal Safety

    [] Do not overreach. Keep proper footing and balance WARNING!READ ANDUNDERSTAND ALL INSTRUCTIONS. Failure to followallinstructions at all times. Proper footing and balance enable better listedbelow, m ayresult i nelectricshock, f ireand/or control of the too! in unexpected situations. serious personal injury. [] Use safety equipment.
  • Page 4 SERVmCE [] When servicing a tool, use only identical replace- ment parts. Follow instructions in the Maintenance [] Tool service must be performed only by qualified section of this manual. Use of unauthorized parts or repair personnel. Service or maintenance performed failure to follow Maintenance hstructions may create a by unqualified personne! may result in a risk of injury.
  • Page 5 could result in a risk of fire and electric shock. If WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions extension cord must be used, make sure: listed below, may result in electric shock, fire a. That pins on plug of extension cord are the and/or serious personal injury.
  • Page 6 Someof the followingsymbolsmaybe usedon this too!. Please studythemand learntheirmeaning. P roper interpretation o f thesesymbolswillallowyouto operate the too!betterandsafer. SYMBOL NAME DESIGNATION/EXPLANATmON Volts Voltage Amperes Current Hertz Frequency ( cyclespersecond) Watt Power Minutes Time Alternating Current Type of current Direct Current Type or a characteristic of current No Load Speed...
  • Page 7 Thefollowing signal w ordsandmeanings a reintended to explain the levels of riskassociated withthisproduct. SYMBOL SIGNAL MEANING DANGER: hdicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: hdicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
  • Page 8: Product Specifications

    PRODUCT SPECiFiCATiONS Chuck ................................3/8 in. Keyless Motor ................................... 19.2 Volt DC Switch ................................Variable Speed No Load Speed ..............................0-1050/min. Charger hput ............................120 V, 60 Hz, A© onJy Charge Rate .................................. 1 hour Torque ..................................150 in.ib. DJRECTJ0N OF SELECTOR (FORWARDiREVERSE CENTER LOCi()
  • Page 9 KNOW YOUR R(GHT ANGLE DRILL-DRIVER FORWARD/REVERSE SELECTOR See Figure 1. (D(RECT(ON OF ROTAT(ON SELECTOR} Before attempting to use this product, familiarize yourself Your dri)Fdriver has a forward/reverse se(ector located w(th al( operating features and safety ru(es. above the switch trigger. KEYLESS CHUCK WR(ST STRAP...
  • Page 10 UNPACKmNG WARNING: Hfany parts are missing do not operate this tool until the missing parts are replaced. Failure This product has been shipped completely assembled. to do so could result in possible serious personal [] Carefully remove the tool and any accessories from the injury.
  • Page 11 CHARGING THE BATTERY PACK WAF{NING: D onotallowfamiliarity withtoolsto makeyoucareless. Remember thata careless Battery packs for this tool are shipped in a low charge fractionofa second issufficient t o inflictserious condition to prevent possible problems. Therefore, you injury. should charge it until the green LED on the front of the charger comes on.
  • Page 12 [] RedLEDshou(d remain onfor approximately 1 hour TO iNSTALL BATTERY PACK thenthegreenLEDwillcomeon.Green LEDon See Figure 3. indicates battery packis fullycharged andcharger i s [] Lock the switch trigger on the drill by p(acing the direc- inma(ntenance charge mode. tion of rotation selector in the center position. NOTE: ThegreenLEDwillremain onunti!the battery [] P(ace the battery pack in the dr(((.
  • Page 13 WARNING:Battery toolsarealways inoperating condition. Therefore, switchshouldalways belocked See Figure 4. whennotinuseor carrying atyourside. The direction of rotation is reversible and is controlled by a selector located above the switch trigger. With the drill SWmTCH held in normal operating position, the direction of rota- See Figure 4.
  • Page 14 INSTALLING B(TS See Figures 6 ° 7. [] Lock the switch tr(gger by p(acing the direction of rota- tion se(ector in center pos(t(on. [] Open or close the chuck jaws to a point where the opening is s(ightly (arger than the bit size you intend to use.
  • Page 15 WARNING:Always wearsafety goggles or safety WARMNG: Be prepared for binding at bit break- glasses withsidesNelds whenoperating tools.Fai!- through. When these situations occur, drill has a ureto do socouldresult i n objects beingthrowninto tendency to grab and kick opposite to the direction youreyes,resulting in possible serious injury.
  • Page 16: Chuck Removal

    CHUCK REMOVAL WARNING:Whenservicing, useonlyidentical Craftsman r eplacement parts.Useofanyotherpart See Figures 10 - 12. maycreatea hazard or cause productdamage. To remove the chuck: [] Lock the switch trigger by placing the direction of rota- tion selector in center position. WARNING:Always wearsafetygoggles or safety glasses withsideshields whenusing compressed a ir [] Insert a 5/! 6 in.
  • Page 17: For Recycling

    [] hsertthehexkeyin chuckandtighten the chuck jawssecurely. Tapsharply witha mallet i n a counter- The battery pack for this tool is equipped with nickel- clockwise direction. Thiswil!loosen thechuckonthe cadmium rechargeable batteries. Length of service from spindle. H t c annowbeunscrewed b yhand. each charging will depend on the type of work you are doing.
  • Page 18 CRAFTSMAN RmGNT ANGLE DRmLL°DR_VER _" MODEL NUMBER 315.101540 ordering repair parts..SEE BACK PAGE FOR PARTS ORDERING _NSTRUCT_ONS Number Description Qty. 6612003 Chuck Screw ....................6903302 Chuck ......................940237057 Data Plate ....................9420316 Logo Plate ....................9002720 Wrist Strap ....................

Table of Contents