Before using this product, read ,, Assembly this manual and follow all Safety ,, Operation Rules and Operating Instructions. ,, Maintenance ,, Parts Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A. www.craftsman.com PRINTED IN U.S.A. FORM NO. 41949 rev. (11/11/11)
A defective product will be replaced free of charge. For warranty coverage details to obtain free replacement, visit the web site: www.craftsman.com This warranty is void if this product is ever used while providing commercial services or if rented to another person.
Remember, any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when using power equipment. • Read the vehicle and sweeper owners manuals and know how to operate your vehicle and sweeper before using this sweeper attachment.
TOOLS REQUIRED FOR ASSEMBLY STEP 3: (SEE FIGURE 3) Secure each bag arm channel to the side of the sweeper housing with a wing nut (31) and a washer 7/16" Wrenches (43) installed on the bolt assembled in step 1. 1/2"...
STEP 5: STEP 7: (SEE FIGURE 5) (SEE FIGURE 7) Slide the bag frame tube (1) through the front flap in Lock the drawbar into position by inserting a 3/8" x 3" pin (20) into the center hole and securing it with a the bottom of the bag.
STEP 9: STEP 11" (SEE FIGURE 9) (SEE FIGURE 11) Slide the front flaps of the hopper bag up onto the Slide the assembled tubes down through the flaps in front of the lower hopper tubes. Secure the bag frame the sides of the hopper bag (3) as shown.
STEP 13: STEP 15: (SEE FIGURE 13) (SEE FIGURE 15) Secure the top and bottom hopper tubes together Insert the hopper support rods (7) into the hole using two 5/16" x 3/4" hex bolts (17) on inside the beneath the curved head bolt (26) in each upper hopper bag and two 5/16"...
ATTACHING SWEEPER HITCH TO TRACTOR STEP 17: (SEE FIGURE 17) Slide the handle grip (29) onto the end of the handle Place the tractor and sweeper on a flat level surface. tube (9). Set the sweeper height adjustment handle to about Assemble the handle tube (9) to the dump tube (5) the middle of its adjustment range.
(SWEEPER SHOWN iN DUMP POSITION) DUMP HANDLE PIVOT ROD DRAWBAR OFFSET DRAWBAR TUBE BAG ARM CHANNELS KNOB HEIGHT ADJUSTMENT HANDLE Dump Lever Permits dumping of the hopper bag from the driver's seat. Bag Arm Channels Connects the hopper bag to the sweeper housing. Pivot Rod Allows the hopper bag to tilt forward to dump material.
CUSTOMER RESPONSiBiLiTiES Read and follow the maintenance schedule and the procedures listed in the maintenance section. MAINTENANCE SCHEDULE _/'_ _Z_'_,/(i'/'L_i z/" H,,,n dates s complete regular service. /___T,,__ Service Dates Check for loose fasteners Check for worn or damaged parts Lubricate brush shaft bearings Lubricate wheel bearings Clean Sweeper...
BRUSH REPLACEMENT GEAR AND DRIVE PiN SERVICE iMPORTANT: Do Not remove both wheels at the same NOTE: Replace brushes one brush at a time. Remove the hopper bag from the sweeper. time to avoid mixing of parts. (The pinion gears are not Loosen hex bolts and lock nuts on two single brush interchangeable.
486.24029 44" HIGH SPEED SWEEPER To order replacement parts, call Sears Parts Direct 1-800-252-1698 or go to www.searspartsdirect.com f_:_Z_- b.'_6"34 %_29 24/" ! // \//42 °'_/2 ot 23 26" ,-63 5 69 36 i !5 54...
486.24029 44" HiGH SPEED SWEEPER To order replacement parts, call Sears Parts Direct 1-800-252-1698 or go to www.searspartsdirect.com REF QTY PART NO DESCRIPTION PART NO DESCRIPTION 42020 Bag Frame Tube 67193 Sweeper Housing 41041 Pivot Rod 67333 Height Adjustment Tube 40890 Hopper Bag 40891...
To order replacement parts, call Sears Parts Direct 1-800-252-1698 or go to www.searspartsdirect.com...