Table of Contents
Advertisement
COPYING
A VIDEO
TAPE
You can make copies of video tapes made by friends or relatives
for your enjoyment.
Warning:Unauthorized
recordings of copyrighted
video tapes
may be an infringement of copyright laws.
Connect the editing (recording) VCR(this unit), source (playing)
VCR(another VCR) and your TV using the following diagram.
NOTES:
• You can use the audio and video input jacks on the front panel
of the editing (recording) VCR instead of using the jacks on
the hack.
• When you connect a monaural VCR(another
source) to this
VCR, connect the Aedio output jack of the monaural VCR(an-
other source) tO the AUDIO IN Ljack of this VCR. The audio
I
signal will be recorded in both L and R channel equally,
i
FiO.10:
I
m_v_
_€_
vc_J
fTVN_
lf._t
VGN
I) Insert a pro-recorded
video cassette into the source (play-
ing) VCR.
2) Insert a blank video cassette, or one you want to record over,
into the editing (recording) VCR cassette compartment.
3) Press the TAPE SPEED button on the editing (recording)
VCR to select the desired recording speed (SP/SLP).
4) Select the "Lineln Rear (L l)" or "Lineln Front (L2)" posi-
tion on the editing (recording)
VCR. See page 13, under
"Connecting
to input jacks".
5) Press the RECORD button on the editing (recording) VCR.
6) Begin playback of the tape in the source (playing) VCR.
• For best results during dubbing, use the VCR's front panel
controls whenever
possible. The remote control might af-
fect the playback VCR's
operation.
• Always use video-quality
shielded cables with RCA-type
connectors.
Standard audio cables are not recommended.
• You can use a video disc player, satellite receiver, or other
audio/video
component
with A/V outputs in place of the
playback VCR.
• If video or color fades in and out, you may be copying
a
copy guarded video tape.
TO MONITOR
THE RECOR1)ING
1) TumontheTVandsettheTVtochannel3or4.
Now [_
set the CH3/CH4 switch on the back of the VCR
IBa_
of
to match the channel selected on the "IV.
meVCR I
2) Press the VCR/I'V button on the editing (lecording)
VCR so that the VCR/TV indicator on the VCR comes on.
ON SCREEN
DISPLAY
* To check the Count,
Clock and Channel
number,
press
the DISPLAY
button on the remote control.
Each time you press the DISPLAY
button, TV screen will
change as shown.
• It is normal for the status display (STOP, PLAY eto,) and
the tape speed display (SP, LP (playback only), or SLP) to
disappear after 5 seconds.
NOTE:VCR power and the VCR/FV indicator must be turned on.
<OFFmode>
_COUNTmode>
<CLOCKmode>
Pres_
Press
once
on¢_
t
!
SPECIAL
FEATURES
minutes, and seconds. (The displayed time will not change
dufing blank portions on the tape.)
• The "-" indication
will appear when the tape is rewound
further than "0:00:00" on the tape counter.
• Thisshowstheelapsedrecordingorplaybacktimeinhours,
Whentheendofatapeisreachedduringrecording,
playback,
or fast-forward,
the tape will automatically
rewind to the be-
ginning. After rewinding
finishes, the VCR will eject the tape
and turn itself to off.
• The tape will not auto-rewind
during timer recording
or
One Touch Recording.
• When the Counter Memory is activated, the tape will rewind
to the M0:00:00 and the VCR will go into the Stop mode.
- 3O -
EN
gJ27
H59M5
Advertisement
Table of Contents
