Sylvania SSV6003 Service Manual
  1. Manuals
  2. Brands
  3. Sylvania Manuals
  4. VCR
  5. SSV6003
  6. Service manual

Sylvania SSV6003 Service Manual

Hide thumbs Also See for SSV6003:
Table of Contents

Advertisement

Quick Links

Download this manual
SERVICE MANUAL
This service manual supplement (SSV6003) contains only
the difference from the original model.
For all other data, see the original service manual for
6260VD.
VIDEO CASSETTE PLAYER
A1X
A2
A3
A8
A10#
A14
S1
X1
X4
X20#
SSV6003
Different parts from original model (6260VD)
Ref. No.
FRONT ASSEMBLY HD412UD
CASE, TOP HD450CD
CHASSIS HD412UD
DOOR, CASSETTE HD412UD
LABEL, RATING HD412UD
LABEL, BAR CODE HD412UD
GIFT BOX CARTON HD412UD
REMOTE CONTROL UNIT 364/CRC007
ACCESSORY BAG
OWNER'S MANUAL HD412UD
Description
Part No.
0VM204159
0VM306022
0VM204176
0VM415164
----------
----------
0VM305977
NA312UD
0VM404632
0VMN03679

Advertisement

Table of Contents
loading

Related Manuals for Sylvania SSV6003

Summary of Contents for Sylvania SSV6003

  • Page 1 SERVICE MANUAL This service manual supplement (SSV6003) contains only the difference from the original model. For all other data, see the original service manual for 6260VD. VIDEO CASSETTE PLAYER SSV6003 Different parts from original model (6260VD) Ref. No. Description Part No.
  • Page 2 Printed in Japan 2003-07-04 HO...
  • Page 3 SERVICE MANUAL Sec. 2: Deck Mechanism Section Sec. 3: Exploded views Sec. 1: Main Section I Standard Maintenance and Parts List Section I Specifications I Alignment for Mechanism I Preparation for Servicing I Exploded views I Disassembly/Assembly of Mechanism I Parts List I Adjustment Procedures I Schematic Diagrams I Alignment Procedures of Mechanism...
  • Page 4 IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.

  • Page 5: Table Of Contents

    MAIN SECTION VIDEO CASSETTE RECORDER 6240VD/EWV403/6260VD/EWV603 Sec. 1: Main Section I Specifications I Preparation for Servicing I Adjustment Procedures I Schematic Diagrams I CBA’s TABLE OF CONTENTS Specifications ................1-1-1 Important Safety Precautions.

  • Page 6: Specifications

    SPECIFICATIONS Description Unit Minimum Nominal Maximum Remark 1. Video 1-1. Video Output (PB) Vp-p SP Mode 1-2. Video Output (R/P) Vp-p SP Mode, 1-3. Video S/N Y (R/P) W/O Burst 1-4. Video Color S/N AM (R/P) SP Mode 1-5. Video Color S/N PM (R/P) SP Mode 1-6.

  • Page 7: Important Safety Precautions

    IMPORTANT SAFETY PRECAUTIONS Product Safety Notice I. Also check areas surrounding repaired locations. J. Be careful that foreign objects (screws, solder Some electrical and mechanical parts have special droplets, etc.) do not remain inside the set. safety-related characteristics which are often not evi- K.
  • Page 8 Safety Check after Servicing Examine the area surrounding the repaired location for Chassis or Secondary Conductor damage or deterioration. Observe that screws, parts, and wires have been returned to their original posi- tions. Afterwards, do the following tests and confirm Primary Circuit Terminals the specified values to verify compliance with safety standards.

  • Page 9: Standard Notes For Servicing

    STANDARD NOTES FOR SERVICING Circuit Board Indications How to Remove / Install Flat Pack-IC a. The output pin of the 3 pin Regulator ICs is indi- 1. Removal cated as shown. With Hot-Air Flat Pack-IC Desoldering Machine: (1) Prepare the hot-air flat pack-IC desoldering Top View Bottom View machine, then apply hot air to the Flat Pack-IC...
  • Page 10 With Soldering Iron: (4) Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply (1) Using desoldering braid, remove the solder from all soldering iron to center of the flat pack-IC and heat pins of the flat pack-IC.
  • Page 11 2. Installation Instructions for Handling Semi-conductors (1) Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA Electrostatic breakdown of the semi-conductors may so you can install a replacement flat pack-IC more occur due to a potential difference caused by electro- easily.

  • Page 12: Preparation For Servicing

    PREPARATION FOR SERVICING How to Enter the Service Mode About REC-Safety Switch Caution: The REC-Safety Switch is directly mounted on the About Optical Sensors Main CBA. When the Deck Mechanism Assembly is Caution: removed from the Main CBA for servicing, this switch does not work automatically.

  • Page 13: Operating Controls And Functions

    OPERATING CONTROLS AND FUNCTIONS [ 6240VD ] Front Panel Remote Control 1. EJECT button 2. NUMBER buttons 3. MENU button POWER EJECT VCR / TV 4. RECORD button 5. SPEED button POWER CHANNEL MENU REC/OTR STOP/EJECT PLAY F.FWD VIDEO AUDIO TAPE IN 6.
  • Page 14 [ EWV403 ] Front Panel Remote Control 1. EJECT button 2. NUMBER buttons 3. MENU button POWER EJECT VCR / TV 4. RECORD button POWER VCR/TV TAPE IN TIMER 5. SPEED button VIDEO AUDIO REC/OTR STOP/EJECT F.FWD PLAY POWER MENU CHANNEL 6.
  • Page 15 [ 6260VD ] Front Panel Remote Control 1. EJECT button 2. NUMBER buttons 3. MENU button POWER EJECT VCR / TV 4. RECORD button 5. SPEED button POWER CHANNEL MENU REC/OTR STOP/EJECT PLAY F.FWD VIDEO L - AUDIO - R TAPE IN 6.
  • Page 16 [ EWV603 ] Front Panel Remote Control 1. EJECT button 2. NUMBER buttons 3. MENU button POWER EJECT VCR / TV 4. RECORD button POWER 5. SPEED button CHANNEL MENU REC/OTR VIDEO L-AUDIO-R POWER VCR/TV TAPE IN TIMER 6. REW button CHANNEL 7.

  • Page 17: Cabinet Disassembly Instructions

    CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart (1): Identification (location) No. of parts in the figures (2): Name of the part This flowchart indicates the disassembly steps to gain (3): Figure Number for reference access to item(s) to be serviced. When reassembling, (4): Identification of parts to be removed, unhooked, follow the steps in reverse order.
  • Page 18 Cylinder FE Head Assembly (L-2) (L-2) AC Head Assembly [4] Deck Assembly [2] Front Assembly (S-3) (L-1) Fig. D2 (S-2) (S-2) [5] Main CBA (S-3) (S-3) From Capstan From From From Motor Cylinder AC Head FE Head Assembly Assembly Assembly [3]VCR Chassis Unit Lead with...
  • Page 19 SW507 LD-SW [5] Main CBA [4] Deck Assembly Cam Gear Hole Shaft Hole LD-SW [5] Main CBA Fig. D5 1-6-3 HD300DC...

  • Page 20: Electrical Adjustment Instructions

    ELECTRICAL ADJUSTMENT INSTRUCTIONS General Note: "CBA" is an abbreviation for "Circuit Board Assembly." NOTE: Figure 1 1.Electrical adjustments are required after replacing circuit components and certain mechanical parts. It is important to do these adjustments only after EXT. Syncronize Trigger Point all repairs and replacements have been com- V-Sync pleted.

  • Page 21: Block Diagrams

    BLOCK DIAGRAMS Servo/System Control Block Diagram MAIN CBA IC501 TP502 AL+5V (SERVO/SYSTEM CONTROL) S-INH RS501 REMOTE KEY- 1 REMOCON-IN SWITCH (DECK ASSEMBLY) SENSOR D555 KEY- 2 S-LED D561 POWER TP513 P-ON+9V AC HEAD ASSEMBLY SWITCH P-ON+5V D565 REC CN504 CTL(+) REC-IND CL504 CONTROL...
  • Page 22 Video Block Diagram REC VIDEO SIGNAL PB VIDEO SIGNAL MODE: SP/REC MAIN CBA TP751 IC501 (OSD) V-OUT Q391 CHARACTER BUFFER JK751 V-OUT IC301 TU701 (VIDEO SIGNAL PROCESS/ HEAD AMP) (TUNER UNIT) VIDEO-IN Q301 CCD 1H BUFFER DELAY VIDEO-OUT CHARA LUMINANCE DOC YNR Y/C COMB SIGNAL PROCESS TUNER...
  • Page 23 Audio Block Diagram PB-AUDIO SIGNAL REC-AUDIO SIGNAL Mode : SP/REC MAIN CBA 6260VD, EWV603 TU701 6260VD, EWV603 SIF OUT 15 6240VD, EWV403 N-A-OUT AUDIO-OUT 14 MOD-A AUDIO-IN 6240VD, EWV403 JK751 A-OUT (R) FROM/TO A-OUT (L) A-OUT (R) Hi-Fi AUDIO A-IN (L) BLOCK A-IN (R) TP753...
  • Page 24 Hi-Fi Audio Block Diagram ( 6260VD, EWV603 PB-AUDIO SIGNAL REC-AUDIO SIGNAL Mode : SP/REC MAIN CBA IC451 (MTS/ SAP/ Hi-Fi AUDIO PROCESS/ Hi-Fi HEAD AMP) CONT SERIAL IIC-BUS SDA FROM/TO DATA IIC-BUS SCL SERVO/ SYSTEM DECODER ST/SAP CONTROL BLOCK DEMOD FILTER DEMOD MATRIX...
  • Page 25 Power Supply Block Diagram CAUTION NOTE : CAUTION ! FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, The voltage for parts in hot circuit is measured using Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. REPLACE ONLY WITH THE SAME TYPE FUSE.

  • Page 26: Function Indicator Symbols

    FUNCTION INDICATOR SYMBOLS Note: The following symbols will appear on the indicator panel to indicate the current mode or operation of the VCR. On-screen modes will also be momentarily displayed on the tv screen when you press the operation buttons. Display panel [ 6240VD/6260VD ] [ EWV403 ]...

  • Page 27: Power Supply Trouble Shooting Guide

    Power Supply Trouble Shooting Guide It is highly recommended that a variable isolation If the tester does not indicate any low resistance value transformer which can monitor current be used. (around 0 ohm), no load is short-circuited and there is (Alternatively a variable AC source which moni- no problem.

  • Page 28: Schematic Diagrams / Cba's And Test Points

    SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replace- ment components rated for higher voltage, wattage, etc.
  • Page 29 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER QUE DES FUSIBLE DE MEMO TYPE.
  • Page 30 Main 1/5 Schematic Diagram REC Video Signal PB Video Signal MAIN 1/5 Schematic Diagram Parts Location Guide REC Audio Signal PB Audio Signal Ref No. Position IC501 COILS L501 L502 L503 L504 TRANSISTORS Q501 Q506 TEST POINTS TP505 TP513 1-9-3 1-9-4 HD310SCM1...
  • Page 31 Main 2/5 Schematic Diagram REC Video Signal PB Video Signal MAIN 2/5 Schematic Diagram Parts Location Guide REC Audio Signal PB Audio Signal Ref No. Position COILS L701 TRANSISTORS Q503 Q504 Q562 Q563 TEST POINTS TP502 TP506 TP751 TP753 TP754 1-9-5 1-9-6 HD310SCM2...
  • Page 32 Main 3/5 Schematic Diagram MAIN 3/5 Schematic Diagram REC Video Signal PB Video Signal Parts Location Guide REC Audio Signal PB Audio Signal Ref No. Position IC301 COILS L251 L303 L304 L421 L422 TRANSISTORS Q301 Q302 Q303 Q391 Q421 Q422 Q425 Q426 TEST POINTS...
  • Page 33 Main 4/5 Schematic Diagram MAIN 4/5 Schematic Diagram Parts Location Guide CAUTION ! Ref No. Position CAUTION Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, If Main Fuse (F1001) is blown, check to see that all components in the power supply REPLACE ONLY WITH THE SAME TYPE FUSE.
  • Page 34 Main 5/5 Schematic Diagram ( 6260VD, EWV603 ) REC Video Signal PB Video Signal MAIN 5/5 Schematic Diagram REC Audio Signal PB Audio Signal Parts Location Guide Ref No. Position IC451 COILS L452 AA-4 TEST POINTS TP452 AA-3 1-9-11 1-9-12 HD410SCM5...
  • Page 35 Main CBA Top View CAUTION ! CAUTION BECAUSE A HOT CHASSIS GROUND IS PRESENT IN THE POWER Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, SUPPLY CIRCUIT , AN ISOLATION TRANSFORMER MUST BE USED. If Main Fuse (F1001) is blown, check to see that all components in the power supply REPLACE ONLY WITH THE SAME TYPE FUSE.
  • Page 36 Main CBA Bottom View MAIN CBA Parts Location Guide Ref No. Position CAUTION CAUTION ! IC001 FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. REPLACE ONLY WITH THE SAME TYPE FUSE. IC002 If Main Fuse (F1001) is blown, check to see that all components in the power supply ATTENTION : POUR UNE PROTECTION CONTINUE LES RISQES...

  • Page 37: Waveforms

    WAVEFORMS (TP751 of Main CBA) (Pin 6 of TU701) (Pin 18 of TU701) WF 1 V-OUT E-E 10usec 50mV x 10 MOD-V 20mV x 10 2msec TU VIDEO 20mV x 10 10usec (TP751 of Main CBA) UPPER (TP302 of Main CBA) (Pin 11 of TU701) LOWER V-OUT...

  • Page 38: Wiring Diagrams

    WIRING DIAGRAM AC CORD FRONT REAR (DECK ASSEMBLY) VIDEO AUDIO AUDIO VIDEO AUDIO AUDIO VIDEO AUDIO AUDIO IN (R) IN (L) IN (R) IN (L) OUT (R) OUT (L) ANT-IN ANT-OUT 6260VD,EWV603 6260VD,EWV603 6260VD,EWV603 AC HEAD ASSEMBLY CL504 AUDIO AE-H ERASE HEAD AE-H/FE-H A-COM...

  • Page 39: System Control Timing Charts

    SYSTEM CONTROL TIMING CHARTS Mode SW : LD-SW LD-SW Position detection A/D Input voltage Limit Symbol (Calculated voltage) 3.76V~4.50V (4.12V) 4.51V~5.00V (5.00V) 0.00V~0.25V (0.00V) 1.06V~1.50V (1.21V) 0.66V~1.05V (0.91V) 1.99V~2.60V (2.17V) 1.51V~1.98V (1.80V) 3.20V~3.75V (3.40V) 0.26V~0.65V (0.44V) 4.51V~5.00V (5.00V) 2.61V~3.19V (2.97V) Note: Note: RS: Loading FWD (LM-FWD/REV “H”)
  • Page 40 Still/Slow Control Frame Advance Timing Chart 1) SP Mode 18 RF-SW The first rise of RF-SW after a rise in F-AD signal F-AD (Internal Signal) "H" "H" "Z" C-DRIVE "L" "L" Stop detection (T2) Acceleration Detection (T1) Slow Tracking Value PB CTL Reversal Limit Value 20ms...
  • Page 41 2) LP/SLP Mode 18 RF-SW The first rise of RF-SW after a rise in F-AD signal F-AD (Internal Signal) "H" "H" "Z" C-DRIVE "L" "L" Stop detection (T2) Acceleration Detection (T1) Slow Tracking Value PB CTL Reversal Limit Value 20ms 27 C-F/R 79 H-A-SW 78 ROTA...
  • Page 42 EJECT ST-S/ END-S "OFF" CASS.LOAD LD-FWD 0.2S LD-REV 0.7S LD-FWD 0.4S LD-FWD 0.2S LD-REV 0.2S LD-FWD 0.5S LD-REV STOP(A) PLAY LD-FWD PLAY LD-FWD LD-REV 0.2S LD-FWD PLAY PLAY PAUSE (SLOW) LD-FWD STILL(SLOW) PLAY LD-REV 0.2S LD-FWD PLAY STOP /EJECT LD-REV STOP(A) Fig.
  • Page 43 STOP(A) STOP LD-REV 0.2S LD-FWD STOP /EJECT 1.0S LD-FWD 0.5S LD-REV STOP(A) LD-REV 0.2S LD-FWD STOP /EJECT LD-REV 1.0S LD-FWD 0.5S LD-REV STOP(A) LD-FWD PAUSE LD-FWD 2.5S Short REV LD-REV 0.2S LD-FWD REC PAUSE REC or PAUSE STOP /EJECT LD-FWD 1.5S LD-REV 0.2S...

  • Page 44: Ic Pin Function Descriptions

    IC PIN FUNCTION DESCRIPTIONS Comparison Chart of Models and Marks Signal Active Mark Function Name Level Model Mark Input Selector 6240VD Control Signal H/Hi-z OUT INSEL/ (EE/Rec)/Still/ EWV403 ST-SL Slow 6260VD (Playback) EWV603 N.U. Not Used Video Head OUT RF-SW Switching IC501( SERVO / SYSTEM CONTROL IC ) Pulse...
  • Page 45 Signal Active Signal Active Mark Function Mark Function Name Level Name Level Playback/ Main Clock OSCI Input CTL (+) Record Control Signal (+) 14.31818MHz Playback/ CTL (-) Record Control Sub Clock Signal (-) Input 32.768 Amp. Output OUT CTL Control Signal Sub Clock for Test Point OUT XO...
  • Page 46 Signal Active Mark Function Name Level “CASSETTE” OUT CAS-IND LED Signal Output TIMER- “TIMER” LED Signal Output RF Conv. Out- put Channel CONV- Switching Sig- Hi-z/L nal 3ch=”Hi-z”, 4ch=”L” RF Conv. ON/ OFF Signal OUT VCR/TV (TV="L"/ VCR="H") Color Phase Rotary OUT C-ROTA Changeover...

  • Page 47: Lead Identifications

    LEAD IDENTIFICATIONS BN1L3Z(P) KTC3202(Y) BA1L3Z-T 2SC1815-BL(TPE2) 2SK3374 BN1F4M-T 2SC1815-Y(TPE2) 2SK3472 BA1F4M-T 2SC1815-GR(TPE2) KTA1266(GR) 2SC3331(T,U) KTC3193(Y) 2SC2120-Y(TPE2) KTC3199(Y,GR,BL) KTC3203(Y) 2SC2785(J,H,F,K) KTC3205 (Y) KRC103M 2SA1015-GR(TPE2) KRA103M KTC3198(Y,GR) KTA1273(Y) 2SA966(Y) KRA110M 2SC2236-Y-TPE6, C KRC110M-AT E C B E C B S D G LA71091M LTV-817(B,C)-F RN1511(TE85R)
  • Page 48 DECK MECHANISM SECTION VIDEO CASSETTE RECORDER 6240VD/EWV403/6260VD/EWV603 Sec. 2: Deck Mechanism Section I Standard Maintenance I Alignment for Mechanism I Disassembly/Assembly of Mechanism I Alignment Procedures of Mechanism TABLE OF CONTENTS Standard Maintenance ..............2-1-1 Service Fixtures and Tools.

  • Page 49: Standard Maintenance

    STANDARD MAINTENANCE Service Schedule of Components H: Hours : Check I: Change Deck Periodic Service Schedule Ref.No. Part Name 1,000 H 2,000 H 3,000 H 4,000 H Cylinder Assembly Loading Motor Assembly Pulley Assembly B587 Tension Lever Assembly AC Head Assembly B573,B574 Reel (SP)(D2), Reel (TU)(D2) Capstan Motor...
  • Page 50 Cleaning Cleaning of Audio Control Head Clean the head with a cotton swab. Cleaning of Video Head Procedure Clean the head with a head cleaning stick or chamois 1.Remove the top cabinet. cloth. 2.Dip the cotton swab in 90% isopropyl alcohol and Procedure clean the audio control head.

  • Page 51: Service Fixtures And Tools

    SERVICE FIXTURE AND TOOLS J-1-1, J-1-2 Ref. No. Name Part No. Adjustment J-1-1 Alignment Tape FL8A Head Adjustment of Audio Control Head J-1-2 Alignment Tape FL8N Azimuth and X Value Adjustment of Audio Control (2Head only) Head / Adjustment of Envelope Waveform FL8NW (4Head only) Guide Roller Adj.Screwdriver...

  • Page 52: Mechanical Alignment Procedures

    MECHANICAL ALIGNMENT PROCEDURES Explanation of alignment for the tape to correctly run B. Method to place the Cassette Holder in the tape- starts on the next page. Refer to the information below loaded position without a cassette tape on this page if a tape gets stuck, for example, in the 1.
  • Page 53 1.Tape Interchangeability Alignment Note: To do these alignment procedures, make sure that the Tracking Control Circuit is set to the center position every time a tape is loaded or unloaded. (Refer to page 2-3-4, procedure 1-C, step 2.) Equipment required: Dual Trace Oscilloscope VHS Alignment Tape (FL8NW) Guide Roller Adj.
  • Page 54 1-A. Preliminary/Final Checking and 3. Check to see that the tape runs without creasing at Alignment of Tape Path Take-up Guide Post [4] or without snaking between Guide Roller [3] and AC Head. (Fig. M3 and M5) Purpose: 4. If creasing or snaking is apparent, adjust the Tilt To make sure that the tape path is well stabilized.
  • Page 55 6. Press CH DOWN button on the unit until the CTL 1-D. Azimuth Alignment of Audio/Control/ waveform has shifted from its original position (not Erase Head the position achieved in step 5, but the position of Purpose: CTL waveform in step 4) by approximately -2msec. To correct the Azimuth alignment so that the Audio/ Make sure that the envelope is simply attenuated Control/Erase Head meets tape tracks properly.

  • Page 56: Disassembly/Assembly Procedures Of Deck Mechanism

    DISASSEMBLY/ASSEMBLY PROCEDURES OF DECK MECHANISM Before following the procedures described below, be sure to remove the deck assembly from the cabinet. (Refer to CABINET DISASSEMBLY INSTRUCTIONS on page 1-6-1.) All the following procedures, including those for adjustment and replacement of parts, should be done in Eject mode;...
  • Page 57 REMOVAL INSTALLATION STEP START- REMOVE/*UNHOOK/ /LOC. PART ADJUSTMENT Fig. No. UNLOCK/RELEASE/ CONDITION UNPLUG/DESOLDER Loading Arm (TU) (+)Refer to Alignment [32] [33] DM2,DM14 Assembly Sec.Pg.2-4-9 [34] [2],[25] M Brake (TU) Assembly DM1,DM15 *(P-7), Brake Belt [35] [2],[25] M Brake (SP) Assembly DM1,DM15 *(P-8) [36] [35]...
  • Page 58 Top View [41] [42] [46] [43] [14] [13] [11] [15] [36] [10] [12] [35] [34] [40] [29] [30] [16] [39] [38] Fig. DM1 Bottom View [20] [33] [32] [24] [26] [27] [25] [23] [28] [22] [21] [31] Fig. DM2 2-4-3 U27NDA...
  • Page 59 (S-1) (S-1) (L-1) (L-3) (L-2) (P-1) Fig. DM5 [46] Fig. DM3 [47] Pin D (L-14) Pin C Pull up Slide Pin A Pin B Slot A (S-2) Slots B Slot A First, while pushing the locking tab as shown in the right, slide and pull up the right side on [2] to release Pin A and Pin B from the slots A.
  • Page 60 (S-4) (S-5) [14] (S-6) [16] [15] Desolder from bottom (S-3) Lead with White Stripe Belt View for A Fig. DM7 Fig. DM9 Adj. Screw [11] [18] (L-4) (L-5) (P-3) [17] [13] [19] [12] (P-4) [10] (P-2) (S-7) Pin of [12] Pin of [10] Fig.
  • Page 61 [22] (C-4) (S-8) (C-1) [23] (L-6) [21] (P-5) [20] Cap Belt (P-5) [28] Fig. DM11 When installing [23], install the spring (P-5) to [28] as shown in the left figure, and then install [23] while Pin on pressing the spring (P-5) to bottom the direction of the arrow in of [23]...
  • Page 62 (P-6) [25] [31] Refer to the Alignment (C-3) Section, Page 2-4-9. (S-9) [29] [33] [30] (L-11) [32] (L-10) (L-8) (C-2) [27] [28] [24] [26] (L-9) Fig. DM14 [36] Position of Mode Lever when installed Break belt Pin of [35] (P-7) Pin of [31] Pin of [34] [34]...
  • Page 63 [42] [41] [43] (L-13) Fig. DM16 [44] [45] Slide Fig. DM17 2-4-8 U27NDA...

  • Page 64: Alignment Procedures Of Mechanism

    ALIGNMENT PROCEDURES OF MECHANISM Alignment 1 The following procedures describe how to align the individual gears and levers that make up the tape Loading Arm (SP) and (TU) Assembly loading/unloading mechanism. Since information about the state of the mechanism is provided to the Install Loading Arm (SP) and (TU) Assembly so System Control Circuit only through the Mode Switch, that their triangle marks point to each other as...
  • Page 65 EXPLODED VIEWS AND PARTS LIST SECTION VIDEO CASSETTE RECORDER 6240VD/EWV403/6260VD/EWV603 Sec. 3: Exploded views and Parts List Section I Exploded views I Parts List TABLE OF CONTENTS Exploded Views ............... . 3-1-1 Mechanical Parts List .

  • Page 66: Exploded Views

    EXPLODED VIEWS Front Panel [ 6240VD/6260VD ] [ EWV403 ] [ EWV603 ] 3-1-1 HD310FEX...
  • Page 67 Cabinet 2L011 2L011 See Electrical Parts List for parts with this mark. 2L011 Some Ref. Numbers are not in sequence. 2L011 2L021 2L021 2L021 2L021 2L021 SENSOR CBA 2B34 2L051 SENSOR CBA MAIN CBA RS501 2L099 2L031 AC001 3-1-2 HD300CEX...
  • Page 68 Packing Some Ref. Numbers are not in sequence. TAPE 2B36 [ EWV403, EWV603 ] 3-1-3 HD310PEX...
  • Page 69 DECK EXPLODED VIEWS Deck Mechanism View 1 Mark Description Floil G-684G or Multemp MH-D (Blue grease) SLIDUS OIL #150 B494 L1467 L1191 B553 B411 B567 L1053 B410 L1051 Chassis Assembly Top View (Lubricating Point) B501 B560 L1450 L1450 B426 L1466 B121 B126 B492...
  • Page 70 Deck Mechanism View 2 Mark Description B589 Floil G-684G or Multemp MH-D (Blue grease) B587 B521 B487 SLIDUS OIL #150 B416 B591 SANKOUL FG84M (Yellow grease) B520 B590 B522 B499 L1406 B148 B508 B573 B592 B574 B558 B564 B557 B594 B414 B565 B525...
  • Page 71 Deck Mechanism View 3 Mark Description Floil G-684G or Multemp MH-D (Blue grease) SLIDUS OIL #150 L1321 B347 L1321 B355 B354 B483 B425 B482 B562 B300 B563 B313 B529 B360 B359 B361 B555 B303 Some Ref. Numbers are not in sequence. B514 3-1-6 U27N4HDEX...

  • Page 72: Mechanical Parts List

    LABEL, BAR CODE HD310UD ---------- LABEL, BAR CODE HD330UD ---------- LABEL, BAR CODE HD410UD ---------- LABEL, BAR CODE HD440UD ---------- LABEL, TELEPHONE NUMBER ---------- H5730UD(SYLVANIA) LABEL, TELEPHONE NUMBER ---------- H7931UD(EMERSON) DECK ASSEMBLY CZD012/VM164U N164UFL DECK ASSEMBLY CZD012/VM166U N166UFL 2B36 LABEL, EAS L0951UB...

  • Page 73: Electrical Parts List

    ELECTRICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Ref. No. Mark Description Part No. # have special characteristics important to safety. ELECTROLYTIC CAP. 2.2µF/250V CE2EMASTH2R2 Before replacing any of these components, read care- M(105?C) C030 CERAMIC CAP.(AX) X K 5600pF/16V CCA1CKT0X562 fully the product safety notice in this service manual.
  • Page 74 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. C328 CHIP CERAMIC CAP.(MELF) F Z 0.01µF/ CZM1CZB0F103 CHIP CERAMIC CAP. F Z 0.1µF/50V or CHD1JZ30F104 16V or CHIP CERAMIC CAP. F Z 0.1µF/25V or CHD1EZ30F104 CHIP CERAMIC CAP.(MELF) F Z 0.01µF/ CZM1CZ30F103 CHIP CERAMIC CAP.
  • Page 75 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. C459 ELECTROLYTIC CAP. 22µF/6.3V M H7 CE0KMAVSL220 C499 ELECTROLYTIC CAP. 4.7µF/25V M H7 CE1EMAVSL4R7 C460 CHIP CERAMIC CAP.(MELF) Y K 4700pF/ CZM1CKB0Y472 C502 ELECTROLYTIC CAP. 220µF/6.3V M H7 CE0KMAVSL221 16V or C505...
  • Page 76 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. CHIP CERAMIC CAP.(MELF) F Z 0.01µF/ CZM1CZ30F103 D563 LED(GREEN) 204-10GD/S957 NPQZ10GDS957 D564 LED(RED) 204HD/E NPQZ00204HDE C540 CHIP CERAMIC CAP.(MELF) F Z 0.01µF/ CZM1CZB0F103 D565 LED(RED) 204HD/E NPQZ00204HDE 16V or D701 ZENER DIODE DZ-33BSDT265 or NDTD00DZ33BS...
  • Page 77 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. CARBON RES. 1/4W J 270 Ω Q426 CHIP TRANSISTOR RN1511(TE85R) or QQ2Z00RN1511 R043 RCX4JATZ0271 CHIP RES.(1608) 1/10W J 1k Ω or CHIP TRANSISTOR FMG4A T148 QQ2Z000FMG4A R056 RRXAJB5Z0102 CHIP RES.(1608) 1/10W J 1k Ω...
  • Page 78 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. CHIP RES.(1608) 1/10W J 1.8k Ω CARBON RES. 1/4W J 100 Ω RRXAJR5Z0182 RCX4JATZ0101 CARBON RES. 1/6W J 820 Ω or R357 PCB JUMPER D0.6-P11.5 JW11.5T R426 RCX6JATZ0821 CARBON RES.
  • Page 79 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. CHIP RES.(1608) 1/10W J 220k Ω or CHIP RES.(1608) 1/10W J 3.9k Ω or R518 RRXAJB5Z0224 R567 RRXAJB5Z0392 CHIP RES.(1608) 1/10W J 220k Ω CHIP RES.(1608) 1/10W J 3.9k Ω RRXAJR5Z0224 RRXAJR5Z0392 CHIP RES.(1608) 1/10W J 1k Ω...
  • Page 80 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. TACT SWITCH TC-1104(H=9.5) SST0101DNG01 TP754 PCB JUMPER D0.6-P9.5 JW9.5T SW502 TACT SWITCH KSM0614B or SST0101HH013 TU701 TUNER UNIT VH025AP or UTUNNTUSP024 TACT SWITCH SKQSAF001A or SST0101AL041 TUNER UNIT TMZH2-001A or UTUNNTUAL030 TACT SWITCH TC-1104(H=9.5) SST0101DNG01...

  • Page 81: Deck Parts List

    DECK PARTS LIST Ref. No Mark Description Part No. Comparison Chart of Models and Marks B492 MODE GEAR MK12 0VM203769 Model Mark B494 C DOOR OPENER MK12 0VM305719 6240VD B499 T LEVER HOLDER MK12 0VM305729 EWV403 B501 WORM HOLDER MK12 0VM203767 6260VD B502...
  • Page 82 Printed in Japan 2003-1-24 HO...

Table of Contents