Advertisement

INTRODUCTION
mOUNTINg ReCOmmeNDaTIONs
faN INsTaLLaTION
OpTIONaL exCLUsIve LIghT fIxTURe INsTaLLaTION
CONTROL feaTURes:
Versa•Touch 2
TROUbLeshOOTINg
safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product
and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this
owner's manual completely and carefully. Retain this manual for future reference.
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the
circuit breaker or fuse box before attempting any installation procedure.
• cauTIoN: rIsK oF eLecTrIcaL shocK! all wiring must be performed in accordance with national and local elec-
trical codes. If you are unfamiliar with the wiring codes, you should use a qualified electrician. To avoid overheating and
possible damage to other equipment, do not install control to a receptacle, fluorescent light fixture, motor operated
appliance, or transformer-supplied appliance.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be uL Listed for ceiling fan
installations, if it is not, a new box must be installed. casablanca extension poles are available for sloped or high ceiling
installations.
• This ceiling fan requires a grounded electrical supply of 120 Vac, 60 hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light
current is 2.8 amps or 340 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
use only genuine Casablanca blades, light fixtures, and accessories.
• The blades in each pack are matched for equal
weight to assure smooth fan operation. If
more than one fan is being installed, be careful
not to mix blades from different cartons.
• Inspect the contents of your carton for
possible shipping or handling damage and
report any such damage directly to your
authorized casablanca dealer.
• It is always a good idea to have an assistant
to help with the installation.
• When cleaning, painting, or working near
your fan, be very careful of the fan and blades.
always turn the power Off to the ceiling fan
before servicing it, working on it, or replacing
light bulbs.
• Never insert anything into the path of the fan
blades while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged in
any way. Contact Casablanca fan Company by
calling 1-888-335-5247, or contact your local
authorized casablanca dealer for assistance
in obtaining service.
CONTENTS
READ AND SAVE THESE INSTRUCTIONS

SAFETY FIRST

BEFORE YOU START
For best performance and for your warranty to be valid,
NOTES
(Remove fuse foR the
ciRcuit you will be
CIRCUIT BREAKER
(tRip bReakeR foR the
ciRcuit you will be
woRking on)
PN 8643520 AT1008
FUSE BOX
woRking on)
11
13
18"
70"
84"
1
1
2
3
9

Advertisement

Table of Contents
loading

Summary of Contents for Casablanca Wilderness

  • Page 1: Safety First

    Off to the ceiling fan (tRip bReakeR foR the before servicing it, working on it, or replacing ciRcuit you will be light bulbs. woRking on) • Never insert anything into the path of the fan blades while the fan is in operation. • Never install a fan over a pool or spa. • Never operate a fan that has been damaged in any way. Contact Casablanca fan Company by calling 1-888-335-5247, or contact your local authorized casablanca dealer for assistance in obtaining service. PN 8643520 AT1008...
  • Page 2: Mounting Recommendations

    MOUNTING RECOMMENDATIONS before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location ceiling fans have practical uses in almost every room in your home. W e suggest you follow these mounting recommendations as you decide where to install your Casablanca fan. • For safety reasons, the fan blades must be a minimum of 7’ above the floor. • Do not locate the fan in a doorway or above a swinging door. • In any installation, the tips of the blades must be at least 18” from the wall in order to provide sufficient clearance for the blades.
  • Page 3: Installation Instructions

    ™ ilderness INSTALLATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. PERMA•LOCK™ HARDWARE ALLEN SET SCREw ALLEN wRENCH ⁄...
  • Page 4: Crossbar Mounting Bracket Installation

    GETTING STARTED Installing a New Ceiling Fixture Outlet Box Using Existing Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish After turning the power OFF at its source (either circuit to place your Casablanca fan, an approved ceiling fixture breaker or fuse box), lower the old fixture and disconnect outlet box must be installed and wired.
  • Page 5: Lag Screw Installation

    ™ ilderness LAG SCREW INSTALLATION Step 3. Pass the lag screw through the center hole of the crosbar mounting bracket and screw into guide hole. Tighten until outlet box is firmly mounted to beam. This box must be firmly secured to the ceiling. We recommend that the ceiling fixture outlet box be of sufficient capacity enabling it to support the weight of fan and light fixture under any conditions.
  • Page 6: Hanging The Fan

    HANGING THE FAN Step 5. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Check that no wires were pinched. Rotate the fan body until the slot in the ball fits into the BALL pin opposite the canopy opening.
  • Page 7: Blade Badge Installation

    ™ ilderness REMOVE DUMMY SWITCH HOUSING & SHIPPING BLOCK Step 10. To reach the blade holder mounting holes in the fan motor the switch housing cap must be removed. Take out the two 8-32 X ” screws securing the switch housing cap and remove.
  • Page 8: Blade/Blade Holder Installation

    BLADE/BLADE HOLDER INSTALLATION Step 12. Using the blade holder screws(pack of 11) attach each blade/bladeholder assembly to the motor. Using the screwdriver, tighten securely by hand only. BLADE HOLDER SCREwS(2 per blade) SWITCH HOUSING BRACKET/ CAP HARDWARE SwITCH HOUSINg mOUNT SCREw SwITCH HOUSINg BRACKET (REmOVED IN STEP 10) 8-32 X...
  • Page 9 ™ ilderness INSTALLING OPTIONAL LIGHT FIXTURE LIgHT FIXTURE mICA SHADE BULB Step 16. Unpack light fixture and make sure everything is accounted for. Refer to the instruction sheet included with each fixture. Step 17. While holding the light fixture up to the fan connect the wires from the fixture to the wires from the fan.
  • Page 10 INSTALLING OPTIONAL LIGHT FIXTURE Step 18. Line up the two clearance holes in the light fixtures with the two threaded holes on the raised rim of the switch housing. Step 19. Using the two 8/32 x 3/8” screws removed in step 10, install the light fixture onto the switch housing.
  • Page 11 •T ® ersa ouch SAFETY FIRST warning: To reduce the risk of electrical shock, this fan must be installed with an isolating wall control/switch. VERSA•TOUCH2 INSTALLATION w-73 CONTROL HOLDER DRYwALL wOOD SCREw SCREw w-73 ANCHOR SCREw 6-32 X ” 6-32 X 1” CONTROL 12V BATTERY 6-32 (2)
  • Page 12: Versa•Touch2 Operation

    •T ® ersa ouch VERSA•TOUCH2 OPERATION LIgHT SEND SIgNAL Fan Control To start the fan. Press the selected speed button to run the fan at the desired speed. 1=Low speed 2=medium speed 3=High speed DOwN To turn off the fan. Press the FAN OFF button. LIgHT LIgHT Airflow Direction...
  • Page 13: Troubleshooting

    Increase the separation between the equipment and receiver, Connect the equipment into an outlet on a circuit different from that to which the receiver is connected, Consult the dealer or an experienced radio/TV technician for help. Note: Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s...
  • Page 14 PRODUCT SPECIFICATIONS Model Name: Wilderness ™ Motor: 188 x 20mm Direct Drive™ Model Number: 86UxxM Blade Span: 54” Blade Iron Pitch: 14° No. of Blades: Dimensions: A =16" Technology: Versa•Touch2® W-73 B = 17" C = 3" NOTE: Dimension B Airflow: 6,772 cfm includes light fixture D = 11.8"...

Table of Contents