Knob Setting - Boss Audio Systems GT-100 Parameter Manual

Parameter Value
OFF
EXP PEDAL
HOLD
ON
KNOB LOCK OFF, ON
OFF, TUNER,
NUM PEDAL Ch . A/B, OD SOLO,
SW A/B SOLO,
A&B SOLO
BANK EXTENT P01–P50,
MIN U01–U50
BANK EXTENT P01–P50,
MAX
U01–U50
PEDAL
OFF, ON
INDICAT

KNOB SETTING

Here you can assign the desired parameters to knobs [1]–[8] in the Play
Screen .
* The settings you make here are only for the knobs in the Play Screen .
Parameter Value
KNOB 1
OFF, PATCH, COMP SUSTAIN, COMP ATTACK, COMP LEVEL,
OD/DS DRIVE, OD/DS TONE, OD/DS E .LEV, OD/DS SOLO LV,
PRE A TYPE, PRE A GAIN, PRE A LEVEL, PRE A BASS, PRE A MID,
KNOB 2
PRE A TREBLE, PRE A PRES, PRE A SOLO LV, PRE A MIC LEV,
PRE B TYPE, PRE B GAIN, PRE B LEVEL, PRE B BASS, PRE B MID,
KNOB 3
PRE B TREBLE, PRE B PRES, PRE B SOLO LV, PRE B MIC LEV,
EQ LO CUT, EQ LOW, EQ LO-MID, EQ HI-MID, EQ HIGH, EQ HI CUT,
KNOB 4
DELAY TIME, DELAY F .BACK,DELAY HI CUT, DELAY E .LEV,
DELAY D1TIME, DELAY D1F .BK, DELAY D1HICUT, DELAY D1LEV,
KNOB 5
DELAY D2TIME, DELAY D2F .BK, DELAY D2HICUT, DELAY D2LEV,
CHORUS RATE , CHORUS DEPTH, CHORUS PREDLY, CHORUS E .LEV,
KNOB 6
REVERB TIME, REVERB HI CUT, REVERB E .LEV, MASTER LOW,
MASTER MID, MASTER HIGH, PATCH LEVEL, PEDAL WAH LEV,
KNOB 7
PEDAL PB LEV, DIV CH SELECT, SR SEND LEVEL, SR RTN LEVEL,
NS1 THRESH, NS1 RELEASE, NS2 THRESH, NS2 RELEASE,
KNOB 8 GLOBAL EQ LOW, GLOBAL EQ MID, GLOBAL EQ HIGH
Explanation
The operational status of the EXP PEDAL's
FUNC (p . 31) is not carried over when patches
are switched .
If the EXP PEDAL's FUNC (p . 31) are the same
between 2 patches, the operational status is
carried over when patches are switched .
For example, if EXP PEDAL FUNC is set to
FOOT VOLUME in both patches, the one
before and the one after the change, the
volume corresponding to the position the
pedal is in (angle) at the time of the patch
change will be maintained after the patch
change . On the other hand, if the patch being
changed to is set to WAH, the volume will be
in accordance with the value set within the
patch, and you'll obtain a wah effect that is
in accordance with a value that reflects the
current position (angle) of the pedal .
Specifies whether knob operations will be
disabled . If this is ON, knob operations will
be disabled .
Selects the function that will be recalled
when you press the pedal of the same
number as the currently selected patch .
Sets the lower limit for the banks .
Sets the upper limit for the banks .
If this is ON, all currently unlit pedal
indicators will blink dimly .
Display of parameters you can set with KNOB
SETTING
The parameter names displayed in the Play screen are abbreviated .
For details about the parameter names, refer to the chart shown below .
Value Display
OFF OFF
PATCH PATCH
COMP SUSTAIN CmpSUS
COMP ATTACK CmpATK
COMP LEVEL CmpLEV
OD/DS DRIVE OD DRV
OD/DS TONE OD TNE
OD/DS E .LEV OD ELV
OD/DS SOLO LV OD SLV
PRE A TYPE A:TYPE
PRE A GAIN A:GAIN
PRE A LEVEL A:LEV
PRE A BASS A:BASS
PRE A MID A:MID
PRE A TREBLE
A:TRB
PRE A PRES
A:PRES
PRE A SOLO LV
A:SLV
PRE A MIC LEV A:MLV
PRE B TYPE B:TYPE
PRE B GAIN B:GAIN
PRE B LEVEL B:LEV
PRE B BASS B:BASS
PRE B MID B:MID
PRE B TREBLE B:TRB
PRE B PRES B:PRES
PRE B SOLO LV B:SLV
PRE B MIC LEV B:MLV
EQ LO CUT EQ LC
EQ LOW EQ LOW
EQ LO-MID EQ LMD
EQ HI-MID EQ HMD
EQ HIGH EQ HI
EQ HI CUT EQ HC
DELAY TIME DlyTIM
SYSTEM
Value Display
DELAY F .BACK DlyFBK
DELAY HI CUT DlyHC
DELAY E .LEV DlyELV
DELAY D1TIME D1 TIM
DELAY D1F .BK D1 FBK
DELAY D1HICUT D1 HC
DELAY D1LEV D1 LEV
DELAY D2TIME D2 TIM
DELAY D2F .BK D2 FBK
DELAY D2HICUT D2 HC
DELAY D2LEV D2 LEV
CHORUS RATE ChoRAT
CHORUS DEPTH ChoDPT
CHORUS PREDLY ChoDLY
CHORUS E .LEV
ChoLEV
REVERB TIME
RevTIM
REVERB HI CUT
RevHC
REVERB E .LEV RevELV
MASTER LOW MT LOW
MASTER MID MT MID
MASTER HIGH MT HI
PATCH LEVEL PAT LV
PEDAL WAH LEV WahLEV
PEDAL PB LEV PB LEV
DIV CH SELECT CH A/B
SR SEND LEVEL SR SND
SR RTN LEVEL SR RTN
NS1 THRESH NS1THR
NS1 RELEASE NS1REL
NS2 THRESH NS2THR
NS2 RELEASE NS2REL
GLOBAL EQ LOW GB LOW
GLOBAL EQ MID GB MID
GLOBAL EQ HIGH GB HI
27