EFFECT
2X2 CHORUS
Frequency band division is employed to produce two different choruses,
one for low frequencies and one for higher frequencies, for both the left
and right channels (for a total of four) . This allows you to achieve a more
natural chorus sound .
Parameter
Value
0–100,
LOW RATE
BPM
–
LOW DEPTH
0–100
0–100,
HIGH RATE
BPM
–
HIGH DEPTH
0–100
LOW PRE
0 .0 ms–40 .0 ms
DELAY
LOW LEVEL
0–100
HIGH PRE
0 .0 ms–40 .0 ms
DELAY
HIGH LEVEL
0–100
XOVER FREQ
100 Hz–4 .00 kHz
18
Explanation
Adjust the speed of the chorus effect for the
low frequency range .
* When set to BPM, the value of each
parameter will be set according to the
value of the "MASTER BPM" specified for
each patch . This makes it easier to achieve
effect sound settings that match the tempo
of the song .
* If, due to the tempo, the time is longer than
the range of allowable settings, it is then
synchronized to a period either 1/2 or 1/4
of that time .
Adjust the depth of the chorus effect for the
low frequency range . If you wish to use this
as a doubling effect, use a setting of 0 .
Adjust the speed of the chorus effect for the
high frequency range .
* When set to BPM, the value of each
parameter will be set according to the
value of the "MASTER BPM" specified for
each patch . This makes it easier to achieve
effect sound settings that match the tempo
of the song .
* If, due to the tempo, the time is longer than
the range of allowable settings, it is then
synchronized to a period either 1/2 or 1/4
of that time .
Adjust the depth of the chorus effect for the
high frequency range . If you wish to use this
as a doubling effect, use a setting of 0 .
Adjusts the delay of the effect sound in
the low-frequency range . Extending the
pre-delay will produce the sensation of
multiple sounds (doubling effect) .
Adjusts the volume of the effect sound in the
low-frequency range .
Adjusts the delay of the effect sound in
the high-frequency range . Extending the
pre-delay will produce the sensation of
multiple sounds (doubling effect) .
Adjusts the volume of the effect sound in the
high-frequency range .
This sets the frequency dividing the low- and
high-frequency ranges .
SUB DELAY
This is a delay with the maximum delay time of 1,000 ms . This effect is
useful for making the sound fatter .
Parameter
Value
Use this to choose the type of delay .
MONO
TYPE
PAN
1 ms–1000 ms,
DELAY TIME
BPM
–
F .BACK
0–100
EFFECT LEVEL 0–120
630 Hz–12 .5 kHz,
HIGH CUT
FLAT
TAP TIME *1
0–100%
DIRECT MIX
0–100
*1 Setting available when TYPE is set to PAN .
Explanation
A simple monaural delay .
Provides a tap delay effect that divides
the delay time between the left and right
channels .
Adjusts the delay time .
* When set to BPM, the value of each
parameter will be set according to the
value of the "MASTER BPM" specified for
each patch . This makes it easier to achieve
effect sound settings that match the tempo
of the song .
* If, due to the tempo, the time is longer than
the range of allowable settings, it is then
synchronized to a period either 1/2 or 1/4
of that time .
Adjusts the volume that is returned to the
input . Higher settings will result in more
delay repeats .
Adjusts the volume of the delay sound .
This sets the frequency at which the high
cut filter begins to take effect . When "FLAT"
is selected, the high cut filter will have no
effect .
Adjusts the delay time of the left channel
delay . This setting adjusts the L channel delay
time relative to the R channel delay time
(considered as 100%) .
Adjusts the volume of the direct sound .