Table of Contents
Advertisement
SYSTEM
OUTPUT SELECT
Specify the device (amp) that's connected to the OUTPUT jacks .
Parameter
Value
JC-120
SMALL AMP
COMBO AMP
STACK AMP
SELECT
JC-120 RETURN
COMBO RETURN
STACK RETURN
LINE/PHONES
INPUT
Adjust the input level according to the output level of the guitar that
you've connected .
Parameter
Value
INPUT LEVEL
-20–+20 dB
GLOBAL EQ
This adjusts the tone of the OUTPUT regardless of the equalizer on/off
settings of individual patches .
Parameter
Value
LOW GAIN
-20–+20 dB
MID GAIN
-20–+20 dB
MID FREQ
20 .0 Hz–10 .0 kHz
MID Q
0 .5–16
HIGH GAIN
-20–+20 dB
26
Explanation
Choose this setting if the GT-100 is connected
to the guitar input of a Roland JC-120 guitar
amp .
Choose this setting if the GT-100 is connected
to a small guitar amp .
Choose this setting if the GT-100 is connected
to the guitar input of a combo-type guitar
amp (i .e ., a single unit that contains the amp
and speaker) other than the JC-120 .
For some types of guitar amps, the "JC-120"
setting might produce better results .
Choose this setting if the GT-100 is connected
to the guitar input of a stack-type guitar amp
(i .e ., one in which the amp and speaker are
separate units) .
Choose this setting if the GT-100 is connected
to the RETURN jack of the JC-120 .
Choose this setting if the GT-100 is connected
to the RETURN jack of a combo-type guitar
amp .
Choose this setting if the GT-100 is connected
to the RETURN jack of a stack-type guitar
amp . You should also choose the "STACK
RETURN" setting if you're using a guitar
power amp together with a speaker cabinet .
Choose this setting if you're using
headphones, or if the GT-100 is connected to
a keyboard amp, mixer, or digital recorder .
Explanation
Adjusts the guitar input level .
Explanation
Adjusts the low frequency range tone .
Adjusts the middle frequency range tone .
Specifies the center of the frequency range
that will be adjusted by the MID GAIN .
Adjusts the width of the area affected by the
EQ centered at the MID FREQ . Higher values
will narrow the area .
Adjusts the high frequency range tone .
TOTAL
These parameters control the threshold level of the noise suppressor used
by each patch, the overall reverb level, and the overall output . They do not
affect the settings of each patch .
Parameter
Value
NS THRESH
-20–+20 dB
REVERB
0–200%
MAIN
OUTPUT
-10 dB, +4 dB
LEVEL
PHRASE LOOP
Here are various settings for the Phrase Loop function .
Parameter
Value
PERFORM
MODE
PATCH EDIT
MONO
REC MODE
STEREO
PLAY LEVEL
0–120
OFF
PEDAL FUNC
PHRASE LOOP
PLAY OPTION
Here you can specify how the pedals will work during performance .
Parameter
Value
WAIT
BANK
CHANGE
MODE
IMMED
Explanation
Control the threshold level of the noise
suppressor used by each patch . This does not
affect the settings of each patch .
* If you want to use the settings specified for
each patch, set this to 0 dB .
Adjusts the reverb level specified for each
patch .
It is useful to adjust the reverb level
appropriately for the space in which you're
performing . This does not affect the settings
of each patch .
* If you want to use the settings specified for
each patch, set this to 100 % .
Specifies the output reference level as
appropriate for the input level of the device
connected to the OUTPUT jacks .
Explanation
The sound processed by the effects will be
recorded .
This lets you create a variety of performances
by layering different sounds .
The sound before being processed by the
effects will be recorded, and the effects will
be applied when the loop is played back .
This is a convenient way to adjust the effects,
or to compare the sound of different patches .
The phrase will be recorded in monaural
(maximum 38 seconds) .
The phrase will be recorded in stereo
(maximum 19 seconds) .
Specifies the phrase playback volume .
Phrase Loop will not operate even if you
press the [PHRASE LOOP] pedal .
You can use the [PHRASE LOOP] pedal to
switch Phrase Loop on/off or to record .
Explanation
Although the indication in the display is
updated to reflect the change in the bank
when a BANK pedal is pressed, the patch will
not change until a number pedal has been
pressed .
The patch switches instantly when a BANK
pedal or any of the number pedals is pressed .
Advertisement
Table of Contents
