HP D7171A - NetServer - LPr Reference Card page 2

HP NetServer LH 3000/3000r
Cabling: Data
D
Front Panel
Display
Cable P/O Display
Power Management / Interconnection Board
To Rear Panel
To Rear Panel OLx Board (Cable P/O Panel)
Management Port
I/O Board
Cabling: Power
To Non-Hot-Swap
Mass Storage
4W
IDE CD-ROM
Flexible Disk Drive
4W 2W
To Secondary (Optional)
Hot-Swap Mass Storage Cage
14W
Power Supply
Redundant Power Supply
Power Supply Control Cable
4
3
2
1
Power Management / Interconnection Board
To Primary Hot-Swap
Mass Storage Cage
14W
Flexible
Non-
Disk Drive
Hot-Swap
Mass
IDE
Storage
CD-ROM
To Optional Mass Storage Device
Primary Hot-Swap Mass
Storage Cage
SCSI A
Secondary (Optional)
Hot-Swap Mass Storage Cage
SCSI B
=
On backside of Power Management /
Interconnection Board
PCI Attention LEDs
(Hot-Swap)
To OLx Connector
(I/O Board)
To Management Port
Connector (I/O Board)
PS1 PS2 PS3 PS4
Rear of Unit
I/O Board
E
PCI Slots 1-6
+5V, 33 MHz,
32 or 64 Bit
PCI
Hold-Down
Remote Management
Latches (1 of 8)
1
2
3
4
Location of
OLx Board
5
6
7
PCI Slot
8
Separator
PCI Slots 7, 8
+3.3V or Universal
Attention LED
33 MHz, 32 or 64 Bit
(Amber)
Power LED (Green)
Hot-Swap Mass
F
Storage Configurations
• Ensure Hot-Swap drives are installed in lowest
or left-most slot first.
• Use SCSI A only for Primary Cage, SCSI B only
for Secondary Cage.
• For duplex configurations, install duplex board
and reconfigure as shown in the 3 diagrams at
right.
• Pedestal configurations are shown here. For
Rack configurations, rotate diagrams 90º clockwise.
• All 1.6" Drives require the use of a .5" Drive Spacebar
Simplex SCSI Addressing
A B A
SCSI A SCSI B
9 15 9
8 14
8 14 8
3 13 3
2 12
2 12
2
1 11
0 10 0
0 10
6 LP 3 HH 1 HH, 4 LP
Key
1.6" Half-Height (HH)
Drive
D8228-80201, Rev A
BARCODE AREA
OLx Connector
Non-Hot-Plug Slots
SE SCSI Connector
(1 - 4)
I/O Memory
(for NetRAID Cache)
Hot-Plug Slots (5 - 8) PCI Slot Separator
(1 of 4)
Duplex SCSI Addressing
A B A B
2 2
1
0
0
2 2
1
0
0
6 LP
HH, LP, HH, LP
B A B A B
15 9 15 9 15
14 8 14
3 13
13
2 12
2 12
12
1 11
10 0 10
0 10
2 LP, HH, 2 LP HH, LP
Alternating
1" Low-Profile (LP)
Drive
For additional information, see other side.
I/O Fan
(Removed)
Blind Mate
Fan
Connector
SCSI A
Connector
SCSI B
Connector
I/O Fan
A B
2
1
0
2
0
1 HH, 4 LP
A B
9 15
8 14
2 12
0 10
2 HH, 2 LP
.5" Drive Spacer