Download Print this page

Ipv4 Setting; Ipv6 Setting; Enable Tcp/Ip; Enable Netware - Sharp MX-M450NA Administration Manual

Administrator settings guide
Hide thumbs

Advertisement

NOTES
About stopped jobs
Printing of received faxes and Internet-Faxes and
transmission of stored fax jobs will automatically
resume after the machine restarts.
For jobs other than the above (copy jobs, print
jobs, document filing print jobs, etc.), the job
information is not retained and thus the stopped
job must be executed again manually (for
example, the original for a copy job must be
placed again and the copy operation repeated).
Operation after optimization starts
Until optimization finishes (or the [CANCEL] key is
touched to cancel optimization),
• The operation panel cannot be used, with the
exception of the [CANCEL] key.
• Operation from the Web page is not possible.
• Faxes and Internet-Faxes cannot be received.
• Print jobs will not be accepted.
• The power will not turn off even if the power
switch is switched off.
• Auto power shut-off mode will not activate even if
the set time elapses. (Preheat mode will
activate.)
Network settings
These settings are set when this product is used as a
network printer.
After you complete the setting for one setting, you must
exit the administrator settings, turn off the main switch,
wait briefly, and then turn on the main switch again
before any other settings can be set. The setting that
was set will be effective after the power is turned on.
The following items can be configured in the "Network
settings".

IPv4 setting

IPv6 setting

Enable TCP/IP

Enable NetWare

Enable EtherTalk

Enable NetBEUI

Reset the NIC

Tandem setting
PING command
NOTE
For setting and modification of "Network settings",
be sure to consult with the network administrator.
IPv4 setting
When using this product in a network that uses the TCP/IP
protocol (IPv4), use this setting to set the IP address (IP
address, IP subnet mask, and IP gateway) of this product.
The setting is set to ENABLE DHCP by factory default
setting, which obtains the IP address setting automatically.
When using this product on a TCP/IP network, be sure to
turn on the "Enable TCP/IP" setting below.
If DHCP is used, the IP address assigned to the
machine may be changed automatically on occasion.
If this happens, printing will not be possible.
IPv6 setting
When using this product in a network that uses the
TCP/IP protocol (IPv6), use this setting to set the IP
address (enable IPv6, DHCPv6, IP address, prefix
length, and default gateway) of this product. By factory
default, the IPv6 setting is disabled. When using this
product on a TCP/IP network, be sure to turn on the
"Enable TCP/IP" setting below.
In an IPv6 environment, the machine can use LPD or
IPP protocol.
If DHCP is used, the IP address assigned to the
machine may be changed automatically on occasion.
If this happens, printing will not be possible.
Enable TCP/IP
When using this product in a network that uses the
TCP/IP protocol, set this setting. Also set the IP
address using the setting "IP address setting" above.
Default setting: Enable
Enable NetWare
When using this product in a network that uses the
NetWare protocol, set this setting.
Default setting: Enable
Enable EtherTalk
When using this product in a network that uses the
EtherTalk protocol, set this setting.
Default setting: Enable
Enable NetBEUI
When using this product in a network that uses the
EtherTalk protocol, set this setting.
Default setting: Enable
Reset the NIC
This setting is used to reset all setting items of NIC
(Network Interface Card) of this product to the factory
default settings.
NOTE
If any of the [NETWORK SETTINGS] were changed
prior to execution of this setting, you must turn off the
power switch after exiting the administrator setting,
wait briefly, and then turn on the power switch to
make the factory default settings take effect.
GENERAL SETTINGS
13

Advertisement

loading

This manual is also suitable for:

Mx-m450nMx-m350n