Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Alliance Laundry Systems W446I
Summary of Contents for Alliance Laundry Systems W446I
- Page 1 Automatic Washers Metered and Nonmetered W446I Para bajar una copia de estas instrucciones en español, visite www.comlaundry.com. Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. 38857R9 June 2007 www.comlaundry.com...
- Page 3 IMPORTANT: Read the complete INSTALLATION/OPERATION INSTRUCTIONS before using the washer. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 38857 WARNING W022...
-
Page 4: Table Of Contents
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Replacement Parts ... - Page 5 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 38857 Operation Instructions for MDC Washers... 26 Step 1: Add Detergent... 26 Step 2: Load Laundry... 26 Step 3: Close Lid... 26 Step 4: Set Fabric Selector and Wash Temperature... 27 Step 5: Insert Money or Card...
-
Page 6: Replacement Parts
Replacement Parts If replacement parts are required, contact the source from which you purchased your washer, or contact: © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Alliance Laundry Systems Shepard Street P.O. Box 990 Ripon, WI 54971-0990 U.S.A. -
Page 7: Safety Information
38857 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information Important Safety Instructions Save These Instructions To reduce the risk of fire, electric shock,... - Page 8 CLOSE the shut-off valves at the end of each wash day. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 21. Loading door MUST BE CLOSED any time the washer is to agitate or spin. DO NOT bypass the loading door switch by permitting the washer to agitate or spin with the loading door open.
-
Page 9: Installation
DO NOT use the special bracket if a 1/4 turn lock is used. 38857 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation Coin Drawer Security – For additional security, drill out the two pilot holes on each side of the front of the meter case to 1/4 or 5/16 inch (6.4 or 7.9 mm) holes... -
Page 10: Dimensions And Specifications
Installation Dimensions and Specifications 25.63 in. (65.09 cm) Pilot Hole 25.63 in. (65.09 cm) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 0.44 in. 26 in. (66.04 cm) (11.11 cm) 28 in. (71.12 cm) METERED MODELS 0.44 in. -
Page 11: Before You Start
For more detailed information refer to section on Water Supply Requirements. 38857 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installing the Washer NOTE: If the washer is delivered on a cold day... -
Page 12: Step 2: Wipe Out Inside Of Washtub
IMPORTANT: Thread hose couplings onto valve connections finger tight, then turn 1/4 turn with pliers. DO NOT cross thread or overtighten couplings. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT COLD Filter Screen (Screen must be facing outward) -
Page 13: Step 4: Connect Drain Hose To Drain Receptacle
Drain Hose Standpipe Figure 6 38857 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT High Standpipe Installation NOTE: No. 562P3 Siphon Break Kit and No. 25863 Hose Coupling are not required for this type of installation. -
Page 14: Step 5: Position And Level The Washer
Cut Hose in This Area and Install No. 25863 Hose Coupling 25863 Hose Coupling Figure 8 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 5: Position and Level the Washer Position washer so it has sufficient clearance for installation and servicing. -
Page 15: Step 6: Plug In The Washer
The washtub is designed to be self- cleaning. Figure 11 38857 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 8: Check Lid Switch Washer should stop filling, agitating and spinning when lid is opened. -
Page 16: Electrical Requirements
CIRCUITS DO NOT USE ADAPTER DO NOT USE AN EXTENSION CORD Figure 13 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 120 ± 12 V.A.C. W227 STANDARD 120 VOLT, 60 HERTZ, 3-WIRE EFFECTIVELY GROUNDED CIRCUIT Ground... -
Page 17: Grounding Instructions
38857 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT DO NOT modify the plug provided with the ● washer – if it will not fit the outlet, have a proper outlet installed by a qualified electrician. -
Page 18: Water Supply Requirements
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT NOTE: Longer fill hoses are available (as optional equipment at extra cost) if the hoses (supplied with the washer) are not long enough for the installation. -
Page 19: Risers
Refer to Figure 16. Risers (Air cushions) Water Supply Faucets Figure 16 38857 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT W005I W005I Installation... -
Page 20: Drain Facilities
A sealed drain system may also allow water to be pumped back into the washer during agitation. Both of these conditions may result in flooding of the washer. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT RECOMMENDED STANDPIPE HEIGHT... -
Page 21: Additional Washer Security
38857 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Enclosed in the shipping bag are four tamper-resistant screws. When used, these screws will provide additional security for your washer. -
Page 22: Operation
If desired, fabric softener may be added to rinse water when RINSE light comes on. Figure 19 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation Step 2: Load Laundry Load dry clothes loosely into washtub – DO NOT... -
Page 23: Step 4: Set Wash Temperature
TWO SPEED WASHERS W385I Figure 23 38857 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 6: Start Washer Metered Models Insert money. Place coin(s) in slide and carefully push in as far as possible and then pull slide out as far as possible. -
Page 24: Indicator Lights
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Should washer stop, but IN USE, RINSE or SPIN light remain on, the motor overload protector may have cycled. -
Page 25: Operation Instructions For Electronic Display Control Washers
If desired, fabric softener may be added to rinse water when RINSE light comes on. Figure 26 38857 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 2: Load Laundry Load dry clothes loosely into washtub – DO NOT overload! -
Page 26: Step 4: Set Fabric Selector
Push touchpad for HOT, WARM or COLD. Light indicates selection. Figure 30 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 6: Insert Money or Card To Insert Money Check pricing as seen on digital display. LID MUST BE CLOSED TO START WASHER. -
Page 27: Copyright, Alliance Laundry Systems Llc – Do Not Copy Or Transmit
It will light at the start of the cycle and remain lit until the cycle is completed. 38857 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT INSERT COINS INSERT COINS is lit to prompt the user for coins to satisfy the vend price. -
Page 28: Operation Instructions For Mdc Washers
If desired, fabric softener may be added to rinse water when RINSE light comes on. Figure 33 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 2: Load Laundry Load dry clothes loosely into washtub – DO NOT... -
Page 29: Step 4: Set Fabric Selector And Wash Temperature
WARM, PERM PRESS/WARM or DELICATES/ COLD. Light indicates selection. Figure 36 38857 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 5: Insert Money or Card To Insert Money Check pricing as seen on digital display. -
Page 30: Step 6: Start Washer
After vend price has been satisfied, push the START pad. LID MUST BE CLOSED TO START WASHER. Figure 39 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Indicator Lights WASH WASH is lit at the beginning of a Wash cycle and will remain lit until the Wash cycle is complete. -
Page 31: Operation Instructions For Netmaster Washers
If desired, fabric softener may be added to rinse water when RINSE light comes on. Figure 40 38857 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 2: Load Laundry Load dry clothes loosely into washtub – DO NOT overload! -
Page 32: Step 4: Set Fabric Selector
Push touchpad for HOT, WARM or COLD. Light indicates selection. Figure 44 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 6: Insert Money or Card To Insert Money Check pricing as seen on digital display. -
Page 33: Step 7: Start Washer
After vend price has been satisfied, push the START pad. LID MUST BE CLOSED TO START WASHER. Figure 47 38857 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Indicator Lights WASH WASH is lit at the beginning of a Wash cycle and will remain lit until the Wash cycle is complete. -
Page 34: Maintenance
10 inches. Middle setting raises water level to 11 inches. The setting on the right raises water level to 13 inches. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Maintenance 4. Carefully reinstall the control panel. -
Page 35: User-Maintenance Instructions
Order filter screen Part No. F270300 from the nearest authorized parts distributor. 38857 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Reinstallation of Shipping Materials Shipping Brace The shipping brace in the lid opening should be saved and reinstalled whenever the washer is moved. -
Page 36: Before You Call For Service
• • • • • • • • © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Won’t Won’t Possible Reason – Do This to Correct Agitate Spin • • Place coin(s) in slide or drop (metered models only). -
Page 37: If Service Is Required
Phone: (920) 748-3121 Nameplate Figure 50 38857 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT When calling or writing about your unit, PLEASE GIVE THE MODEL AND SERIAL NUMBERS. The model and serial numbers are located on the nameplate. -
Page 38: Information For Handy Reference
Service Agency Address NOTE: Record the above information and keep your sales slip. Model and serial numbers are located on the nameplate. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Serial Number Phone Number Phone Number... -
Page 40: Installer Checklist
Fast Track for Installing the Washer (Refer to the manual for more detailed information) ➊ • Remove the Shipping Brace and Shipping Plug. CHECK ➋ • Wipe Out Inside of Washtub. CHECK ➌ • Connect Fill Hoses. CHECK ➍ • Connect Drain Hose to Drain Receptacle.
Need help?
Do you have a question about the W446I and is the answer not in the manual?
Questions and answers