Alliance Laundry Systems WF065B Installation & Maintenance
  1. Manuals
  2. Brands
  3. Alliance Laundry Systems Manuals
  4. Washer
  5. WF065B
  6. Installation & maintenance
Alliance Laundry Systems WF065B Installation & Maintenance

Alliance Laundry Systems WF065B Installation & Maintenance

Washer-extractors
Hide thumbs Also See for WF065B:
Table of Contents

Advertisement

Quick Links

Washer-Extractors
Commercial Softmount
Refer to Page 11 for Model Identification
Original Instructions
Keep These Instructions for Future Reference.
CAUTION: Read the instructions before using the machine.
(If this machine changes ownership, this manual must accompany machine.)
Part No. D2418ENR6
www.alliancelaundry.com
October 2023

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WF065B and is the answer not in the manual?

Questions and answers

Marty Lawrence
January 16, 2025

I **** looking for a parts list & an error code list for model # wf180b

0

Subscribe to Our Youtube Channel

Related Manuals for Alliance Laundry Systems WF065B

Summary of Contents for Alliance Laundry Systems WF065B

  • Page 1 Washer-Extractors Commercial Softmount Refer to Page 11 for Model Identification Original Instructions Keep These Instructions for Future Reference. CAUTION: Read the instructions before using the machine. (If this machine changes ownership, this manual must accompany machine.) Part No. D2418ENR6 www.alliancelaundry.com October 2023...

  • Page 3: Table Of Contents

    Electrical Installation Requirements..............50 © Copyright 2023, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher.
  • Page 4 Emergency Unblocking of Door Lock.............77 Care of Stainless Steel................... 77 Disposal of Unit..................78 Disconnecting the Machine................78 Disposal of Unit....................78 China Restriction of hazardous substances (RoHS)....... 79 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 5: Safety Information

    NOTE: The word “NOTE” is used to communicate in- stallation, operation, maintenance or servicing informa- tion that is important but not hazard related. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 6: Important Safety Instructions

    Do not install the machine over an open water stor- age or drain system. Adequate ventilation must be provided to avoid the back flow of gases into the room from appliances burning other fuels. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 7 Old hose sets should not be reused. The machine is not designed for use in IT networks. Applicable measures need to be provided. Electrical - Energy Prevention © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 8 Avoid contact with hot inlet water temperatures high- er than 125° Fahrenheit [51°C] or hot surfaces. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 9 • Always contact your dealer, distributor, service agent or the manufacturer on any problems or conditions you do not understand. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 10 NOTE: If literature or replacement parts are required, contact the source from which the machine was pur- chased or contact Alliance Laundry Systems at +1 (920) 748-3950 for the name and address of the nearest authorized parts distributor.

  • Page 11: Introduction

    Signed for and on behalf of: Alliance Laundry CE s.r.o. Místecká 1116 742 58 Příbor Czech Republic CZW264N Radim Polednik, Quality Manager, 1/1/2023 Figure 1 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 12 SYR065V SYU065V TUM_TOUCH_OPL SY80_QUAN- SYA080V SYR080V SYU080V TUM_TOUCH_OPL SY105_QUAN- SYA105V SYR105V SYU105V TUM_TOUCH_OPL SY135_QUAN- SYA135V SYR135V SYU135V TUM_TOUCH_OPL SY180_QUAN- SYA180V SYR180V SYU180V TUM_TOUCH_OPL Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 13 UYX180V UYX240V UYX280V FORM_TOUCH_OPL UYA065V UYA080V UYA105V UYA135V UYA180V UYA240V UYA280V UYR065V UYR080V UYR105V UYR135V UYR180V UYR240V UYR280V UYU065V UYU080V UYU105V UYU135V UYU180V UYU240V UYU280V © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 14: Regulatory Statements

    Users of this product are cautioned not to make modifications or CANADA - CAN ICES-3(B)/NMB-3(B) changes that are not approved by Alliance Laundry Systems, This device contains license-exempt transmitter(s)/receiver(s) LLC. Doing so may void the compliance of this product with ap-...
  • Page 15 Commission. Article 14 The operation of the low-power radio-frequency devi- ces is subject to the conditions that no harmful interference is MIX4N_SVG Figure 2 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 16: Serial Plate Location

    520I000001DK was manufactured in May 2015. Manufacturing Date - Year Year Serial Number Character 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 Table 1  continues... © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 17: Delivery Inspection

    © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 18: Specifications And Dimensions

    Wash Cylinder Information Cylinder di- 20.87 [530] 20.87 [530] 24.40 [620] 24.40 [620] 29.53 [750] 29.53 [750] 29.53 [750] ameter in. [mm] Table 3  continues... © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 19 24.41 [620] depth in. [mm] Cylinder vol- 2.3 [65] 2.65 [75] 3.71 [105] 4.77 [135] 6.36 [180] 8.48 [240] 9.9 [280] ume ft Table 3  continues... © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 20 PSI [bar] [kPa] Hot water, °F 185 [85] 185 [85] 185 [85] 185 [85] 185 [85] 185 [85] 185 [85] [°C] Table 3  continues... © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 21 240 L 280 L cations Models Models Models Models Models Models Models Noise Emissions Wash se- quence, dB Extract se- quence, dB Table 3  continues... © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 22 Relative Hu- 30%-90% without condensation midity Height above up to 3280 [up to 1000] sea level ft. Storage Tem- 34-131 [1-55] perature, °F [°C] Table 3 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 23: Machine Dimensions

    22. Drain valve or recycle valve - 3 in. [76 mm] 280 L Models only) 23. Hidden USB port (under top cover) - standard Figure 4 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 24 8.58 [218] 8.58 [218] 4.44 [113] 4.44 [113] 4.44 [113] 4.44 [113] 4.44 [113] 4.44 [113] 4.44 [113] 7.99 [203] 10.79 [274] 2.64 [67] Table 4 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 25: Machine Dimensions (Models With Filter For Mops)

    31.30 [795] 31.30 [795] 38.19 [970] 38.19 [970] 38.19 [970] 8.43 [214] 8.43 [214] 8.43 [214] 8.43 [214] 8.98 [228] 8.98 [228] 8.98 [228] Table 5 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 26: Machine Dimensions (Models With Base Frame With Built-In Filter For Mops)

    11.38 [289] 7.09 [180] 10.83 [275] 7.09 [180] 7.09 [180] 9.06 [230] 9.06 [230] 9.06 [230] 9.06 [230] 10.63 [270] 10.63 [270] 10.63 [270] Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 27 13.78 [350] 13.78 [350] 13.78 [350] 13.78 [350] 11.81 [300] 11.81 [300] 11.81 [300] * - Models with "V" in 7th position of model number © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 28: Mounting Bolt Hole Locations

    Specifications and Dimensions Mounting Bolt Hole Locations Figure 7 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 29 5.90 [150] 5.90 [150] 1.96 [50] 1.96 [50] 1.96 [50] 3.94 [100] 3.94 [100] 3.94 [100] 38.18 [970] 38.18 [970] 38.18 [970] Table 7  continues... © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 30 70 lb. / 180 L 240 L 280 L Specification Models Models Models 34.31 [871.5] 39.62 [1006.5] 42.60 [1082] 25.98 [660] 31.30 [795] 34.25 [870] Table 7 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 31: Mounting Bolt Hole Locations (Models With Base Frame With Built-In Filter For Mops)

    27.95 [710] 26.30 [668] 31.61 [803] 34.57 [878] 1.77 [45] 1.77 [45] 1.77 [45] 1.77 [45] 1.77 [45] 1.77 [45] 1.77 [45] Table 8  continues... © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 32 .63 [16] .63 [16] .63 [16] .63 [16] .63 [16] 25.28 [642] 27.24 [692] 27.24 [692] 33.07 [840] 34.21 [869] 39.53 [1004] 42.48 [1079] Table 8 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 33: Floor Mounting Layout

    20 [500] (minimum) Dimensional clear- 35.43 [900] 35.43 [900] 35.43 [900] 35.43 [900] 43.31 [1100] 43.31 [1100] 43.31 [1100] ance above ma- chine (minimum) Table 9 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 34: Installation

    9. Lower the machine until the beams rest on the wooden with either of the rear corners first. The machine's side blocks. panel can be damaged. 10. Repeat this handling at other machine side. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 35: Mounting Bolt Installation

    5. Mount the anchoring bolts in the holes drilled in the floor. 6. Position washers and locknuts on machinery anchor bolts and finger-tighten to machine base. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 36: Shipping Brace Removal

    3, 4 CZW208N 1. Front panel 2. Rear panel 3. Front transport holder 2pcs 4. Rear transport holder 2pcs Figure 12 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 37: Top And Front Panel Reinstallation

    3. Areas that must be pressed until a click is heard to lock the panels in place (* - does not apply to models with central payment systems) Figure 13 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 38: Machine Installation

    14 . Tighten to a torque of 50 Nm. 12. Remove the shipping brace. Refer to Shipping Brace Remov- 13. Re-install the front and rear panels on the machine. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 39: Machine Installation With Base Frame With Built-In Filter For Mops

    3. Spring washer; supplied with the machine 4. Washer; supplied with the machine 5. Base frame 6. Anchor bolt; supplied with the machine 7. Concrete floor Figure 15 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 40 3. Remove washer and bolt from the anchoring bolt and install anchoring bolt into the pre-drilled hole. 4. Install the plinth base. 5. Install washer and nut. Tighten nut. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 41: Drain Connection

    Avoid sharp bends which may prevent proper draining. The drainage pipe should be located over a floor drain, drainage channel. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 42 Model Requirement Drain connection number Drain connection size, in. [mm] 3 [76] Average flow rate of draining gal/min. [l/ 55.48 [210] min.] Table 12  continues... © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 43 Drain Line Sizing / Minimum Drain ID, in. [mm] A - 1 Machine B - 2 Machines C - 3 Machines 3 [75] 4 [100] 5 [125] Table 13 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 44: Drain Pump 6.5 Kg / 14 Lb. / 65 L And 7.5 Kg / 20 Lb. / Models Outside Of North America

    In order to achieve good draining, the hose must not bend at a sharp angle. Refer to Figure 20 . 1. Drain hose bend Figure 20 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 45: Water Connection Requirements

    / 240 L Models, to connect cold water, use a hose with plastic elbow. To connect hot water, use a hose with metal elbow. Do not re-use water hoses; only use new water hoses. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 46 1. Refer to Table 14 . 2. Refer to Table 14 . 3. Refer to Table 14 . 4. Cover Figure 24 Water type Water connection Table 14  continues... © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 47: Connecting Hoses

    For mounting on the back panel, use 3 pieces of 4x11, Alliance Laundry Systems, LLC ranges of front loading commer- TORX T20 screws from the machine package.
  • Page 48 5. Install this end of hose to water supply tab (Black colored coupling for BSPP thread) 6. Filter Screens 7. Dual Check Valves Figure 25 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 49: Water Reuse System

    A pump must transport the recuperated water from the tank to the Connection - outside diam- 0.75 [19] washer. The requirements for the pump depend on the number eter, in. [mm] © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 50: Electrical Installation Requirements

    When you have long distances in the electrical installation, it may be necessary to use big- ger cables to reduce the voltage drop. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 51: Residual Current Device (Rcd) - Models Outside Of North America

    7. Protective conductor 8. Incoming Field Wiring Terminal 9. Neutral conductor Figure 28 IMPORTANT: Alliance Laundry Systems warranty does not cover components that fail as a result of improper input voltage. Residual Current Device (RCD) - Models Outside of North America...

  • Page 52: Supply Cable

    (6) for L1, L2, (L3), (N) conductors. Make sure there is no accidental contact, since the supply cable stays un- der voltage even when the main switch is off. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 53: Machine Protective Earth Connection And Equipotential Bonding

    16 ). However, for the protection purposes, with the supply cable 5. L3 cross section of a min. 4 mm , select a larger conductor section, 6. L2 i.e., 6 mm 7. L1 Figure 30 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 54: Input Power Conditioning

    Three-phase machines require a separate, three-phase in- Connect the electrical service's wires to the machine's electrical verse-time circuit breaker to prevent damage to the motor by dis- connection terminal as shown. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 55 Connect the electrical service's wires to the machine's electrical connection terminal as shown. For voltage supply systems with- out neutral, N is replaced by L2. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 56: Three-Phase Connections

    Machine's Electrical Machine's Electrical Electrical Service Wire Connection Terminal Electrical Service Wire Connection Terminal Supply Ground Neutral Supply Ground Table 20 Table 21 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 57: Phase Adder

    Machines can be converted for lower voltage operation and/or 50 Hz operation. Refer to conversion label by serial plate for details. IMPORTANT: Do not use a phase adder on any ma- chine. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 58: Electrical Specifications - Models Outside Of North America

    9.3* 440-480 50/60 3 (L1, L2, 0.85 11.6 (7) 0.6* 7.3* 13.8 (9) 9.3* *Models with "V" in 7th position of model number Table 22 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 59 9.5* 440-480 50/60 3 (L1, L2, 0.85 11.7 (7) 0.7* 7.5* 13.9 (9) 9.5* *Models with "V" in 7th position of model number Table 23 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 60 18.5 (9) 9.5* 12.8 22.8 (12) 12.5* 380-415 50/60 3 (L1, L2, 10.1 (6) 0.9* 6.5* 15.5 (9) 9.5* 12.8 19.9 (12) 12.5* Table 24  continues... © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 61 3 (L1, L2, 12.8 (7) 0.9* 7.5* 14 (9) 9.5* 12.8 18.2 (12) 12.5* *Models with "V" in 7th position of model number Table 24 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 62 4 (L1, L2, 10.1 13 (6) L3, N) 1.2* 7.0* 10.1 18 (9) 10.0* 13.1 22.6 (12) 13.0* 14.9 27 (13.8) 14.8* Table 25  continues... © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 63 3 (L1, L2, 13.2 (7) 1.2* 8.0* 10.1 14.8 (9) 10.0* 13.1 18.7 (12) 13.0* *Models with "V" in 7th position of model number Table 25 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 64 30.5 (18) 440-480 50/60 3 (L1, L2, 13.5 19.7 (12) 1.7* 19.5 27.2 (18) *Models with "V" in 7th position of model number Table 26 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 65 3 (L1, L2, 31.5 (18) 2.0* 440-480 50/60 3 (L1, L2, 28.2 (18) 2.0* *Models with "V" in 7th position of model number Table 27 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 66 37 (21.9) 2.0* 24.0* 440-480 50/60 3 (L1, L2, 23.9 34 (21.9) 2.0* 24.0* *Models with "V" in 7th position of model number Table 28 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 67: Electrical Specifications - North American Models

    CSA (A) 200-240 50/ 60 2 (L1, L2 or 14.2 12 (4) L1, N) 440-480 50/ 60 3 (L1, L2, L3) 5.2 14 (2.5) Table 32 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 68: Steam Requirements (Steam Heat Option Only)

    Use an inlet steam pressure hose only adapted to the steam valve with appropriate seal suitable for the applied working pressure. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 69: Chemical Injection Supply System

    If one of the connec- soap and brings it into the tub assembly. tions is open, close and secure the opening with an ap- propriate cover. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 70: Electrical Connection Of External Liquid Soap Supply System

    . Refer to Figure 40 . Such connection is possible only with machines which had been or- dered with the "Heating Delay / Waiting for Detergent" option. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 71: Chemical Soap Supply System

    Figure 41 shows a typical chemical injection supply system. Chemical Injection Supply System 1. Injection Point 2. Chemical Dispenser Pump Outlet 3. PVC Pipe Figure 41 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 72: Maintenance

    2. Clean the door glass and between the door gasket and the door with a damp cloth. 3. Clean supply dispenser lid and general area with mild deter- gent. Flush the dispenser with clean water. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 73 Refer to Figure 46 . CFS674N_SVG 1. Filter Figure 43 2. Remove the front cover of the filter base frame. Refer to Fig- ure 44 . © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 74: Quarterly

    Try to turn the door in a clockwise or counterclockwise rotation. If the door can me moved clockwise or counter- clockwise, replace the door hinges. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 75: Every 6 Months

    Torque, Hz Table 38 6.5 kg / 14 lb. / 67 - 70 64 - 67 6. Adjust the safety switch. 65 L Table 37  continues... © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...
  • Page 76 18 kg - 28 kg / 0.04 ± 0.04 [1 ± 1] 40 lb. - 70 lb. / 180 L - 280 L Table 39 © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 77: Emergency Unblocking Of Door Lock

    If the stainless steel appears to be rusting, the source of the rust may be an iron or steel part not made of stainless steel, such as a nail or screw. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 78: Disposal Of Unit

    For more detailed information about recycling of this product, please contact the local city office, household waste disposal service, or the source from which the product was purchased. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

  • Page 79: China Restriction Of Hazardous Substances (Rohs)

    NOTE: The referenced Environmental Protection Use Period Marking was determined according to normal oper- ating use conditions of the product such as temperature and humidity. This product under normal use, durable years of environmental protection is 15 years. © Copyright, Alliance Laundry Systems LLC - Part No. D2418ENR6 DO NOT COPY or TRANSMIT...

This manual is also suitable for:

Wr080bWr280bnWf080bWr105bWr280bWf105b ... Show all

Table of Contents

Save PDF