Page 1 Washer-Extractors Cabinet Hardmount Refer to Page 5 for Model Identification NOTA: El manual en español aparece después del manual en inglés. CHM166C Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. F232135R6 www.comlaundry.com June 2005...
Page 3: Table Of Contents
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information... Explanation of Safety Messages...
Page 5: Safety Information
F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information Important Safety Instructions To reduce the risk of fire, electric shock, serious injury or death to persons when...
Page 6 If this occurs, have washer checked by a qualified service person. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 19. Replace worn power cords and/or loose plugs. 20. Be sure water connections have a shut-off valve and that fill hose connections are tight.
Page 7: Introduction
HC50NX2 HC25MN2 HC35MX2 HC50SN2 HC25MX2 HC35NC2 HC50VC2 HC25MY2 HC35NR2 HC50VX2 HC25NC2 HC35NX2 HC60AC2 F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction HC60ACV HC80NRV SC25MD2 HC60AL2 HC80NXV SC25ML2 HC60ALF HC80VCV SC25MN2 HC60ALV HC80VNV SC25MX2 HC60AX2...
Page 8: Delivery Inspection
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Nameplate Location The nameplate is located at the rear of the machine and inside door.
Page 9 Option Identification (varies from machine to machine) 0001 * Denotes Brand *C40AC2OU60001 00000000000 208 – 240 F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Model Number Familiarization Guide Sample Model Number: *C40AC2OU60001 500000 EXAMPLE OF NAMEPLATE Figure 2 Introduction...
Page 10: Replacement Parts
Customer Service For technical assistance, call (920) 748-3121, Ripon, Wisconsin U.S.A. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Remove After Shipment (OPL Models Only) A yellow retainer has been inserted in the door locks...
Page 11: Specifications And Dimensions
(349) Cylinder volume, ft 2.76 (78.1) Perforation size, in. (mm) 0.188 (4.76) Perforation open area, % F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 2 Speed Models 27, 30 30-1/8 (660) (737) (765) 45-7/8 47-1/4...
Page 12 Wash/reverse speed, RPM High extract speed, RPM Centrifugal Force Data Wash/reverse centrifugal force, Gs High extract centrifugal force, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 2 Speed Models (Continued) 27, 30 14-11/32 (305) (364) 14-3/8...
Page 13 (kg) Electrical Heating (Optional) Total electrical heating capacity, Electrical heating elements Electrical heat element size, kW F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 2 Speed Models (Continued) 18/20 27, 30 (13) (13) (13) 1.4 (1.01) 1.59 (1.15) 1.91 (1.37) 2.69 (1.94) 2.84 (2.04) 3.59 (2.59) 3.59 (2.59)
Page 14: Gap Setting For Vibration Switch (Variable-Speed And Fixed-Speed Models)
NOTE: The standard position of the switch is open, or non-tripped. 3. Tighten nuts on switch extension after adjusting the gap. Measure the gap distance to verify accurate setting. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 27, 30 0.030-0.040 0.020-0.030 (0.76-1.02) (0.51-0.64)
Page 15 For 18, 20, 25, 27, 30 and 35 Pound Capacity Machines Sump Gap Distance F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Figure 4 Specifications and Dimensions CHM1995N Vibration Switch Switch Extension CHM1995N...
Page 16 Specifications and Dimensions For 40 and 50 Pound Capacity Variable-Speed and Fixed-Speed Machines Sump Gap Distance © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Vibration Switch Switch Extension Figure 5 CHM2000N F232135...
Page 17 For 60 Pound Capacity Variable-Speed and Fixed-Speed Machines Lower Bracket Upper Bracket Vibration Switch F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions Balance Bolt Lock Nut Gap Distance Figure 6 CHM1999N CHM1999N...
Page 18 Specifications and Dimensions For 80 Pound Capacity Machines Switch Extension Gap Distance © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Vibration Switch Figure 7 CAB1998N CHM1998N F232135...
Page 19 For 125 Pound Capacity Machines Vibration Switch Gap Distance F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions Switch Extension Figure 8 CHM1993N...
Page 20 Door opening size, in. (mm) Height of door bottom above floor, in. (mm) Power Consumption Average power used per cycle, kW-hr Average HVAC load, Btu/hr © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Variable-Speed and Fixed-Speed Models 30-1/8 30-5/8 (660)
Page 21 Electrical heating elements Electrical heat element size, kW * Refer to Gap Setting for Vibration Switch (Variable-Speed and Fixed-Speed Models) section for specifications. F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT (1.5) (1.5) (1.5) (1.5) 0.25...
Page 22 Input Power Block External Chemical Supply Signal Terminal Strip (OPL only) Cold Water Inlet © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Hot Water Inlet Extra Inlet Valve External Chemical Supply Inlet (OPL only) Vacuum Breaker...
Page 23 (30 mm) (30 mm) 3 in. 3 in. (76 mm) (76 mm) F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Machine Capacity Dimensions 27, 30 24 in. 26 in. 25-3/4 in. (610 mm) (660 mm) (654 mm) 17 in.
Page 24 56-3/4 in. (1422 mm) 1 in. (25 mm) 70-1/2 in. (1791 mm) 44-1/2 in. (1130 mm) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 125 POUND CAPACITY MACHINES Hot Water Inlet Liquid Chemical Inlet Steam Inlet (Optional)
Page 25: Installation
(305 mm) (305 mm) *For 80 pound models intended for standard mounting, clearance should be 6 in. (150 mm). F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation FRONT Machine Capacity Dimensional Clearances 27, 30 2 in.
Page 26: Machine Foundation
125 Models 12 in. (304 mm) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT The machine must be anchored to a smooth, level surface so that the entire base of the machine is supported and rests on the mounting surface. (Do not support the machine on only four points.)
Page 27 IMPORTANT: Do not install any variable-speed machine on an elevated base frame. Machine Base Mounting Bolt Threads Grouting Bolt-Locator Fixture or Rebar Frame Figure 10 F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT P035I P035I Installation...
Page 28 Dynamic pressure, l bs-ft (kN-m Dynamic load frequency, Hz Maximum moment about machine base, lbs-ft (kN-m) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Floor Load Data, 2 Speed Models 27, 30 (2.44) (2.90) (3.58) 106.3 (4.94)
Page 29: Machine Anchoring
– one after the other – until all are tightened evenly and the machine is fastened securely to the floor. Refer to Figure 12. F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 2-9/16 in. (65 mm) Figure 11...
Page 30 4. Drill and chisel out a conical hole large enough to accept the J-bolt. Refer to Figure 14. Figure 14 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 5. Use compressed air or a squeeze bulb to remove debris from each hole. Anchor J-bolt in place, using an industry-accepted anchoring compound.
Page 31 Refer to Table 1. NOTE: Be sure to recheck the J-bolts 1 week after installation. F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Figure 16 Figure 17 shows the completed J-bolt installation with grout.
Page 32: Mounting Bolt Template Part Numbers (Without Elevated Base Frame)
Laundry Systems at (920) 748-3121. Refer to Table 5 for specific Part Numbers when ordering. Machine 18/20 27/30 50/60 Table 5 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Part No. F608707 F608708 F631796 F608709 F0637047-00...
Page 33: Mounting Bolt Hole Locations (Without Elevated Base Frames)
27 AND 30 POUND (65 mm) *For close mounting, use mounting bolt pattern labeled “A”; for standard mounting, use “B.” F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 20.66 in. 2.68 in. (525 mm) (68 mm) 34.88 in.
Page 34: Mounting Bolt Hole Locations (Without Elevated Base Frames)
41.5 in. (1054 mm) 80 POUND* *For close mounting, use mounting bolt pattern labeled “A”; for standard mounting, use “B.” © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 3.28 in. (83 mm) 2.03 in. (52 mm)
Page 35: Mounting Bolt Hole Locations (With Elevated Base Frames)
(70 mm) 27 AND 30 POUND *For close mounting, use mounting bolt pattern labeled “A”; for standard mounting, use “B.” F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 2.87 in. (73 mm) 20.66 in. 2.87 in.
Page 36: Mounting Bolt Hole Locations (With Elevated Base Frames)
2.22 in. (56 mm) 60 POUND *For close mounting, use mounting bolt pattern labeled “A”; for standard mounting, use “B.” © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 3.62 in. (92 mm) 3.47 in. (88 mm) 36 in.
Page 37: Elevated Base Frame Installation
F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 3. Adjust the drill depth gauge to match the length of the J-bolt, minus 1-1/2 inches (38 mm). 4. Drill and chisel out a conical hole large enough to accept the J-bolt.
Page 38 Refer to Figure 16. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 12. Position the machine over the base frame, aligning the mounting holes on the machine with the corresponding holes on the frame.
Page 39: Concrete Foundation Installation
1 in. (25 mm) Minimum 4 in. (102 mm) Minimum F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 2. Excavate the floor to a depth of approximately 9 inches (230 mm) below the floor surface, making certain that the sides of the hole slope outwards from top to bottom.
Page 40 COMPACTED FILL DIRT 24 in. (609 mm) DEPTH 12 in. (305 mm) 6 in. (152 mm) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT LENGTH FOR ONE MACHINE COMPACTED FILL DIRT 18 in. (457 mm) DEPTH 80 POUND CAPACITY MODELS 47-1/2 in.
Page 41 If grouting is not required, proceed to step 13. F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9. Raise and level the machine 1/2 inch (13 mm) off the foundation on three points, using spacers such as nut fasteners.
Page 42: Drain Connection
Drain Tee * 1 foot (0.3 m) minimum between water inlet valve and vent pipe. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Use the supplied black rubber adapter and clamps to transition from the machine drain outlet to the two...
Page 43 3 in. (76 mm) 3 in. (76 mm) 80, 125 F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Refer to Table 6 for capacity-specific drain information. NOTE: Installation of additional machines will require larger drain connections. Refer to Table 7.
Page 44: Water Connection Requirements
2 in. (50 mm) 2 in. (50 mm) 2-1/2 in. (70 mm) Table 8 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Suitable air cushions should be installed in supply lines to prevent “hammering.” Refer to Figure 30. Hot/Cold 1/2 in.
Page 45: Electrical Installation Requirements
If a delta supply system is used on a four-wire model, connect high leg to L3. F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT IMPORTANT: Alliance Laundry Systems warranty does not cover components that fail as a result of improper input voltage.
Page 46: Connection Specifications
Do not connect ground to neutral (N-white wire) leg at terminal strip. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Phase Adder If three-phase service is unavailable for a 2 speed...
Page 47 200 – 240 50/60 NOTE: Wire sizes shown are for copper, THHN, 90° conductor per NEC article 310. F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Specifications 18 and 20 Pound Capacity Models Standard...
Page 48 50/60 1 or 3 2 or 3 NOTE: Wire sizes shown are for copper, THHN, 90° conductor per NEC article 310. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Specifications 35 Pound Capacity Models Standard...
Page 49 1 or 3 2 or 3 6.3/6.3 NOTE: Wire sizes shown are for copper, THHN, 90° conductor per NEC article 310. *Coin models only. F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Specifications 50 Pound Capacity Models Standard...
Page 50 200-240 50/60 200-240 50/60 NOTE: Wire sizes shown are for copper, THHN, 90° conductor per NEC article 310. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Specifications 60 Pound Capacity Models Standard 2 Speed Models...
Page 51 200 – 240 50/60 NOTE: Wire sizes shown are for copper, THHN, 90° conductor per NEC article 310. F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Specifications 80 Pound Capacity Models Standard Variable-Speed Models 12.4...
Page 52: Troubleshooting
4. If control circuit fuse has blown, replace with fuse of appropriate rating as identified by decal. IMPORTANT: Call a qualified electrician if replacement fuse blows. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Steam Requirements (Steam Heat Option Only) WARNING Hot Surfaces.
Page 53: Supply Dispensing (Opl Machines Only)
IMPORTANT: Failure to follow these instructions could damage the machine and void the warranty. F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Connection of External Liquid Supplies 18 – 80 Pound OPL Models 1. Facing the rear of the machine, locate the 1-1/2 inch (38 mm) opening found at the upper right-hand side of the valve panel.
Page 54 Do not use L1 or L2 with the common line to deliver 120VAC to chemical injection supply pumps if the machine is equipped with a control transformer. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dangerous Voltages. Will cause damage to the machine and microprocessor. Do not attempt to obtain 110VAC by using L1 or L2 with the common.
Page 55 Supply Dispenser Lid Dry Supply Cups Dry Supply Insert Four Way Water Valve Supply Dispenser Figure 33 F232135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT P048I P048I Installation DESIGN 6 CHM2001N Strain Relief for Liquid Chemical Supply...
Page 56: Control Function Test
Attempt to start the machine with the door open. The machine should not start with the door open. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT c. Close the door without locking it and attempt to start the machine. The machine should not start with the door unlocked.
Page 57 Lavadoras extractoras Montaje fijo en gabinete Consulte la página 61 para la identificación de modelos CHM166C Guarde estas instrucciones para referencia en el futuro. (Si esta máquina cambia de dueño, asegúrese de que este manual vaya con la misma). Pieza No. F232135R6 www.comlaundry.com Junio 2005...
Page 59 F232135 (SP) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Información de seguridad ... 59 Explicación de los Mensajes de seguridad ... 59 Instrucciones importantes de seguridad...
Page 61: Información De Seguridad
F232135 (SP) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Instrucciones importantes de seguridad ADVERTENCIA Para reducir el riesgo de incendios, electrocución y lesiones graves o mortales...
Page 62 Si ocurre esto, pida a una persona de servicio cualificada que inspeccione la lavadora. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 19. Sustituya los cordones de alimentación desgastados y los enchufes aflojados.
Page 63: Introducción
HC50NX2 HC25MN2 HC35MX2 HC50SN2 HC25MX2 HC35NC2 HC50VC2 HC25MY2 HC35NR2 HC50VX2 HC25NC2 HC35NX2 HC60AC2 F232135 (SP) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introducción HC60ACV HC80NRV SC25MD2 HC60AL2 HC80NXV SC25ML2 HC60ALF HC80VCV SC25MN2 HC60ALV HC80VNV SC25MX2...
Page 64: Inspección De Entrega
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Posición de la placa de identificación La placa de identificación está situada en la parte trasera de la máquina y en el interior de la puerta.
Page 65 0001 * Indica marca *C40AC2OU60001 00000000000 208 – 240 500000 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) Muestra de un número de modelo: *C40AC2OU60001 EJEMPLO DE PLACA DE IDENTIFICACIÓN Figura 2 Introducción CHM2008N...
Page 66: Piezas De Recambio
Servicio al cliente Para obtener asistencia técnica, llame a (920) 748- 3121, Ripon, Wisconsin U.S.A. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Retirar después del envío (modelos OPL solamente) Se ha insertado un retenedor amarillo en los pestillos...
Page 67: Especificaciones Y Dimensiones
(2,76) Tamaño de perforación 4,76 mm (plg) (0,188) Área abierta de la perforación % F232135 (SP) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Modelos de 2 velocidades 27, 30 (26) (29) (30-1/8) 1143 1165 1200...
Page 68 Datos de fuerza centrífuga Fuerza centrífuga de lavado/ inversión de giro, Gs Fuerza centrífuga alta de extracción, Gs © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Modelos de 2 velocidades (continuación) 27, 30 (12) (12) (14-11/32)
Page 69 Calentamiento eléctrico (optativo) Capacidad total de calentamiento eléctrico, Elementos de calentamiento eléctrico Tamaño del elemento de calentamiento eléctrico, © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) 27, 30 DATOS DATOS DATOS 13 mm 13 mm...
Page 70: Ajuste De Separación Para El Interruptor De Vibración (Modelos De Velocidad Variable Y Modelos De Velocidad Fija)
3. Apriete las tuercas de la extensión del interruptor después de haber ajustado la separación. Mida la distancia de separación para verificar la exactitud del ajuste. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 27, 30 0,635- 0,762-...
Page 71 Para máquinas de capacidad de 18, 20, 25, 27, 30 y 35 libras Sumidero Distancia de la separación © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) Figura 4 Especificaciones y dimensiones CHM1995N Interruptor de vibración Extensión del interruptor...
Page 72 Para máquinas de velocidad variable y máquinas de velocidad fija de capacidad de 40 y 50 libras Sumidero Distancia de la separación © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Interruptor de vibración Extensión del interruptor Figura 5 CHM2000N...
Page 73 60 libras Soporte inferior Soporte superior Interruptor de vibración © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) Especificaciones y dimensiones Perno de equilibrio Tuerca de seguridad Distancia de separación...
Page 74 Especificaciones y dimensiones Para máquinas de capacidad de 80 libras Extensión del interruptor Distancia de la separación © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Interruptor de vibración Figura 7 CAB1998N CHM1998N F232135 (SP)
Page 75 Para máquinas de capacidad de 125 libras Interruptor de vibración Distancia de la separación © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) Especificaciones y dimensiones Extensión del interruptor Figura 8 CHM1993N...
Page 76 (plg) Consumo de potencia Potencia promedio usada por ciclo, kW-hora Carga media de CA de alto voltaje, BTU/hora © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT (26) (29) (30-1/8) 1089 1165 1200...
Page 77 * Consulte las especificaciones de la sección de Ajuste de separación para interruptor de vibración (modelos de velocidad variable y velocidad fija). © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) 0,25 0,25...
Page 78 Tira de terminal de señal de suministro químico externo (OPL solamente) Entrada de agua fría Entrada de agua caliente © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Válvula de entrada adicional Entrada de suministro químico externo (OPL solamente) Válvula reguladora de vacío...
Page 79 (1-3/16 plg) (1-3/16 plg) 76 mm 76 mm (3 plg) (3 plg) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) Dimensiones de capacidad de la máquina 27, 30 610 mm 660 mm 654 mm...
Page 80 1422 mm (56-3/4 plg) 25 mm (1 plg) 1791 mm (70-1/2 plg) 1130 mm (44-1/2 plg) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT MÁQUINAS DE CAPACIDAD DE 125 LIBRAS B023I Entrada de agua caliente Entrada de productos químicos líquidos...
Page 81: Instalación
(12 plg) (12 plg) * Para modelos de 80 libras diseñados para montaje estándar, la separación deberá ser de 150 mm (6 plg). F232135 (SP) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Instalación FRONTAL 27, 30...
Page 82: Cimientos De La Máquina
Modelos 125 304 mm (12 plg) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT La máquina debe estar anclada a una superficie horizontal lisa de modo que toda la base de la máquina esté apoyada y descanse en la superficie de montaje.
Page 83 Consulte la Figura 10. IMPORTANTE: No instale una máquina de velocidad variable sobre un bastidor de base elevada. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) Base para la máquina Roscas del perno de montaje Lechada Dispositivo para localizar pernos o armazón...
Page 84 Frecuencia de carga 11,5 dinámica, Hz Máximo momento de la 1,33 base de la máquina, kN- (979) m (lbs-ft) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 27, 30 2,44 2,90 3,,58 (549) (653) (804) 4,94...
Page 85: Anclaje De La Máquina
Consulte la Figura 12. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) (2-9/16 plg)
Page 86 J. Consulte la Figura 14. Figura 14 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 5. Use aire comprimido o una pera de compresión eliminar los residuos de cada agujero. Fije los pernos en J en su lugar usando un compuesto para anclaje industrial aceptado.
Page 87 Consulte la Tabla 1. NOTA: Asegúrese de volver a verificar los pernos en J una semana después de la instalación. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) Figura 16 La Figura 17 muestra la instalación completa con pernos en J y con lechada de cemento.
Page 88: Números De Pieza De La Plantilla De Pernos De Montaje (Sin Bastidor De Base Elevada)
Alliance Laundry Systems. Consulte la Tabla 5 para obtener información para solicitar piezas. Máquina 18/20 27/30 50/60 Tabla 5 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Pieza No. F608707 F608708 F631796 F608709 F0637047-00...
Page 89: Ubicaciones De Los Orificios De Los Pernos De Montaje (Sin Bastidores De Base Elevada)
27 Y 30 LIBRAS *Para montaje cercano, use el patrón de montaje de pernos “A”; para montaje estándar use el patrón de montaje de pernos “B”. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP)
Page 90: Ubicaciones De Los Orificios De Los Pernos De Montaje (Sin Bastidores De Base Elevada)
80 LIBRAS* *Para montaje cercano, use el patrón de montaje de pernos “A”; para montaje estándar use el patrón de montaje de pernos “B”. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 83 mm (3,28 plg)
Page 91: Ubicaciones De Los Orificios De Los Pernos De Montaje (Con Bastidores De Base Elevada)
27 AND 30 LIBRAS *Para montaje cercano, use el patrón de montaje de pernos “A”; para montaje estándar use el patrón de montaje de pernos “B”. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP)
Page 92: Ubicaciones De Los Orificios De Los Pernos De Montaje (Con Bastidores De Base Elevada)
60 LIBRAS *Para montaje cercano, use el patrón de montaje de pernos “A”; para montaje estándar use el patrón de montaje de pernos “B”. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 92 mm (3,62 plg)
Page 93: Instalación De Bastidor En Base Elevada
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) 3. Ajuste el medidor de profundidad de perforación para que coincida con la longitud de los pernos en J, menos 38 mm (1-1/2 pulgada).
Page 94 Consulte la Figura 17. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 12. Coloque la máquina sobre el bastidor de base, alineando los agujeros de montaje en la máquina con los agujeros correspondientes en el bastidor.
Page 95: Instalación En Cimiento De Concreto
203 mm (8 plg) 25 mm (1 plg) mínimo 102 mm (4 plg) mínimo © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) 2. Excave el suelo a una profundidad de aproximadamente 230 mm (9 pulgadas) debajo de la superficie, asegurándose de que los lados...
Page 96 609 mm (24 plg) DE PROFUNDIDAD 305 mm (12 plg) 152 mm (6 plg) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT TIERRA DE RELLENO COMPACTADA DE MODELOS DE 80 LIBRAS DE CAPACIDAD 1207 mm (47-1/2 plg)
Page 97 Si no se requiere lechada de cemento, continúe con el paso 13. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) 9. Levante y nivele la máquina 13 mm (1/2 pulgada) sobre el cimiento en tres puntos, usando espaciadores tales como sujetadores de tuerca.
Page 98: Conexión De Drenaje
T de drenaje * 0,3 m (1 pie) mínima entre la válvula de entrada de agua y la tubería de ventilación. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Utilice el adaptador de caucho negro suministrado y abrazaderas para hacer la transición del desagüe de la...
Page 99 76 mm (3 plg) 76 mm (3 plg) 76 mm (3 plg) 80, 125 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) Consulte la Tabla 6 para obtener información de desagüe según capacidad. NOTA: La instalación de máquinas adicionales requerirá...
Page 100: Requisitos De La Conexión De Agua
(2 plg) 70 mm (2-1/2 plg) Tabla 8 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Se deben instalar amortiguadores de aire adecuados en las tuberías de suministro para prevenir golpes. Consulte la Figura 30. Caliente/Fría...
Page 101: Requisitos De La Instalación Eléctrica
Si se usa un sistema de suministro delta en un modelo de cuatro cables, conecte el cable de alta tensión al terminal L3. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) IMPORTANTE: La garantía de Alliance Laundry Systems no cubre componentes que fallen como resultado de un voltaje de entrada inadecuado.
Page 102: Especificaciones De Conexión
No conecte la conexión a tierra a un cable neutro (cable blanco N) en la tira de terminales. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Dispositivo de adición de fases Si no hay un servicio trifásico disponible para un modelo de 2 velocidades y se utiliza un Roto-Phase u otro dispositivo de adición de fases, conecte el cable...
Page 103 200 – 240 50/60 NOTA: Los tamaños de los cables mostrados son para cobre, THHN, conductor de 90° según el artículo 310 de NEC. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) Especificaciones eléctricas Modelos de capacidad de 18 y 20 libras Estándar...
Page 104 1 ó 3 NOTA: Los tamaños de los cables mostrados son para cobre, THHN, conductor de 90° según el artículo 310 de NEC. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Especificaciones eléctricas Modelos de 35 libras de capacidad Estándar...
Page 105 NOTA: Los tamaños de los cables mostrados son para cobre, THHN, conductor de 90° según el artículo 310 de NEC. *Modelos con monedas solamente. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) Especificaciones eléctricas Modelos de 50 libras de capacidad Estándar...
Page 106 50/60 NOTA: Los tamaños de los cables mostrados son para cobre, THHN, conductor de 90° según el artículo 310 de NEC. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Especificaciones eléctricas Modelos de 60 libras de capacidad Estándar...
Page 107 200 – 240 50/60 NOTA: Los tamaños de los cables mostrados son para cobre, THHN, conductor de 90° según el artículo 310 de NEC. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) Especificaciones eléctricas Modelos de 80 libras de capacidad Estándar...
Page 108: Localización Y Resolución De Problemas
IMPORTANTE: Llame a un electricista cualificado si se funden los fusibles de repuesto. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Requisitos de vapor (opción de calentamiento de vapor solamente) ADVERTENCIA Superficies calientes causará...
Page 109: Distribución De Suministro (Máquinas Opl Solamente)
IMPORTANTE: De no seguir estas instrucciones se podría dañar la máquina y anular la garantía. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) Conexión de suministro de líquido externo Modelos OPL de 18 –...
Page 110 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT No use L1 ni L2 con la línea común para suministrar 120 VCA a bombas de suministro por inyección de productos químicos, si la máquina está...
Page 111 Tapa de dispensador de suministros Tazas de suministro seco Inserto de suministros secos Válvula de agua de cuatro vías Distribuidor de suministro Figura 33 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232135 (SP) P048I P048I Instalación DISEÑO 6 CHM2001N Protección contra tirones para las líneas de...
Page 112: Prueba De Función De Control
La máquina no debe ponerse en marcha con la puerta abierta. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT c. Cierre la puerta sin bloquearla e intente poner en marcha la máquina. La máquina no debe ponerse en marcha con la puerta sin bloquear.

This manual is also suitable for:

Hc18md2 Hc18mn2 Hc18mx2 Hc18nc2 Hc18nr2 Hc18nx2 ... Show all

Alliance Laundry Systems Washer-Extractor Installation Manual

English

Safety Information

Introduction

Specifications and Dimensions

Installation

Español

Información de Seguridad

Introducción

Especificaciones y Dimensiones

Instalación

Available languages

Quick Links

Chapters

Need help?

Questions and answers

Related Manuals for Alliance Laundry Systems Washer-Extractor

Summary of Contents for Alliance Laundry Systems Washer-Extractor

This manual is also suitable for:

Table of Contents